HAMPTON BAY H35-NG2 Quick start guide

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
WARNING:
If the information in these instructions are not followed ex-
actly,afireorexplosionmayresultcausingpropertydamage,
personal injury or loss of life.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
Installation and service must be performed by a qualified
installer, service agency or the gas supplier.
FOR YOUR SAFETY
What to do if you smell gas:
Do not try to light any appliance
Do not touch any electrical switch:
do not use any phone in your
building.
Immediately call your gas supplier
from a neighbour's phone. Follow
the gas supplier's instructions.
If you cannot reach your gas
supplier, call the fire department.
918-838
MODELS: H35-NG2 Natural Gas H35-LP2 Propane
11/09/09
H35 Direct Vent Gas Fireplace
H35 Direct Vent Gas Fireplace
Owners &
Installation Manual
Tested by: Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
www.hampton-fire.com

WARNING
HOT GLASS
DO NOT TOUCH
NEVER
WILL
CAUSE BURNS
GLASS
UNTIL COOLED
ALLOW CHILDREN
TO TOUCH GLASS
CHILDREN AND ADULTS SHOULD BE ALERTED TO
THE HAZARDS OF HIGH SURFACE TEMPERATURES,
ESPECIALLY THE FIREPLACE GLASS, AND SHOULD
STAYAWAYTOAVOIDBURNSORCLOTHINGIGNITION.

2 Hampton®H35-2 Direct Vent Freestanding Gas Stove
HAMPTON®
Direct Vent Freestanding Gas Stove
UNIT DIMENSIONS
* Unit shown with optional side shelves.
To the New Owner:
Congratulations!
You are the owner of a state-of-the-art Hampton®Gas Stove by REGENCY FIREPLACE PRODUCTS .
The H35-2 is a hand crafted appliance and has been designed to provide you with all the warmth and charm of a wood
fireplace at the flick of a switch. The model H35-2 has been approved by Warnock Hersey for both safety and efficiency.
As it also bears our own mark, it promises to provide you with economy, comfort and security for many trouble free years
to follow. Please take a moment now to acquaint yourself with these instructions and the many features of your
Hampton® Stove.
25” (835mm)
15-3/8” (391mm)
16-3/4” (425mm)
26-1/4” (667mm)
28” (711mm)
38-1/4” (972mm)
26-7/8” (683mm)
21” (533mm)

Hampton®H35-2 Direct Vent Freestanding Gas Stove 3
TABLE OF CONTENTS
Wiring Diagrams..........................................................36
Wall Thermostat ..........................................................37
Remote Control ..........................................................37
Final Check..................................................................38
OPERATING INSTRUCTIONS
Operating Instructions .................................................38
Lighting Procedure ......................................................38
Shutdown Procedure...................................................38
First Fire ......................................................................38
Copy of the Lighting Plate Instructions .......................39
Adjusting Flame Height ...............................................39
Automatic Convection Fan Operation..........................39
MAINTENANCE
Normal Operating Sounds of Gas Appliances.............40
Maintenance Instructions.............................................40
General Vent ...............................................................41
Maintenance................................................................41
Log Replacement ........................................................41
Glass Replacement.....................................................41
Fan Maintenance.........................................................41
Removing Valve...........................................................42
Installing Valve Assembly............................................42
PARTS LIST
Main Assembly ............................................................43
Burner & Log Assembly...............................................44
WARRANTY
Warranty......................................................................47
UNIT DIMENSIONS
Unit Dimensions ............................................................2
SAFETY LABEL
Copy of Safety Label.....................................................4
INSTALLATION
Specifications ................................................................6
Information for Mobile / Manufactured Homes .............6
General Safety Information............................................7
Installation Checklist......................................................7
Clearances to Combustibles..........................................7
Locating Your Gas Stove...............................................8
Manufactured Mobile Home Requirements...................8
Combustion and Ventilation Air......................................8
Optional Fan Installation................................................8
Venting Introduction.......................................................9
Installation Precautions .................................................9
Safety Precautions for The Installer ..............................9
Vent Restrictor Position.................................................9
Exterior Vent Terminal Locations.................................10
4” x 6-5/8” Rigid Pipe ..................................................11
Cross Reference Chart only........................................11
Rigid Pipe Venting Systems ........................................13
Rotating 45oElbow for Horizontal Terminations ..........14
Venting Arrangements.................................................14
Venting Arrangements ................................................15
Vertical Termination With Co-linear Flex System.........18
DV Stove Horizontal Vent Kit.......................................19
Dura-Vent Termination Kit............................................21
Dura-Vent Horizontal Installations...............................22
Dura-Vent Vertical Termination....................................23
Converting ..................................................................25
Class-A Metal or Masonry Chimney............................25
Cathedral Ceilings.......................................................26
High Elevation .............................................................26
Gas Connection...........................................................26
Aeration Adjustment ....................................................27
Gas Pipe Pressure Testing..........................................27
Conversion from NG to LP ..........................................28
Conversion to Lower BTU Rating................................32
Optional Brick Panel....................................................33
Log Set Installation......................................................33
Double Door Removal.................................................34
Optional Side Shelves Installation...............................35

4 Hampton®H35-2 Direct Vent Freestanding Gas Stove
This is a copy of the label that accompanies
each Direct Vent Freestanding Gas Stove.
We have printed a copy of the contents here
for your review.
SAFETY LABEL
NOTE:Hampton®unitsareconstantlybeing
improved. Check the label on the unit and if
there is a difference, the label on the unit is
the correct one.
COPY OF SAFETY LABEL
Listed: VENTED GAS FIREPLACE HEATER /
FOYER AU GAZ À ÉVACUATION
Certified for/Certifiée pour: CANADA and U.S.A.
WN# 16478
Tested to: CGA 2-17-M91, ANSIZ21.88a-2007/CSA 2.33a-2007
MAY BE INSTALLED IN MANUFACTURED (MOBILE) HOMES AFTER FIRST SALE
DO NOT REMOVE THIS LABEL / NE
PAS ENLEVER CETTE ÉTIQUETTE
Minimum supply pressure
Manifold pressure High
Manifold pressure Low
Maximum Input
Minimum Input
Orifice size
Altitude
Minimum supply pressure
Manifold pressure High
Manifold pressure Low
Maximum Input
Minimum Input
Orifice size
Altitude
5" WC/C.E. (1.25 kPa)
3.8" WC/C.E. (0.94 kPa)
1.1" WC/C.E. (0.27 kPa)
36,000 Btu/h (10.55 Kw/h)
18,000 Btu/h (5.28 Kw/h)
#33 DMS (2.87mm)
0-4500 ft/pi (0-1372m)
Pression d'allimentation minimum
Pression à la tubulure d'échappement élevée
Pression à la tubulure d'échappement basse
Débit Calorifique maximum
Débit Calorifique minimum
Dimensions de l’orifice
L’altitude
Pression d'allimentation minimum
Pression à la tubulure d'échappement élevée
Pression à la tubulure d'échappement basse
Débit Calorifique maximum
Débit Calorifique minimum
Dimensions de l’orifice
L’altitude
FACTORY EQUIPPED FOR NATURAL GAS Model:H35-NG2
Convertible to 30,000
Orifice Size
Maximum Input
Minimum Input
Altitude
#37 DMS
30,000 Btu/h (8.78 Kw/h)
14,300 Btu/h (4.19 Kw/h)
0-4500 ft/pi (0-1372m)
Dimensions de l'orifice
Débit Calorifique maximum selon
Débit Calorifique minimum selon
L’altitude
Dimensions de l'orifice
Débit Calorifique maximum selon
Débit Calorifique minimum selon
L’altitude
FACTORY EQUIPPED FOR PROPANE GAS Model:H35-LP2
12" WC/C.E. (3.00 kPa)
11" WC/C.E. (2.74 kPa)
2.9" WC/C.E. (0.72 kPa)
34,000 Btu/h (9.97 Kw/h)
17,500 Btu/h (5.13 Kw/h)
#51 DMS (1.70mm)
0-4500 ft/pi (0-1372m)
Convertible to 28,500 Btu
Orifice Size
Maximum Input
Minimum Input
Altitude
This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1, or Natural Gas
and Propane Installation Code, CSA B149.1.
This appliance must be installed in accordance with the Standard CAN/CSA Z240 MH, Mobile Housing, in Canada, or with the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States, or when such a standard is not applicable, ANSI/NCS-
BCS A225.1/NFPA 501A, Manufactured Home Installations Standard or ANSI A119.2 ou NFPA 501C Standard for Recreational Vehicles
This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located,
manufactured (mobile) home where not prohibited by local codes. See owner's manual for details.
Installer l'appareil selon les codes ou règlements locaux, ou, en l'absence de tels règlements, selon les codes d'installation ANSI Z223.1, Na-
tional Fuel Gas Code ou CSA-B149.1 en vigueur.
Installer l'appareil selon la norme CAN/CSA-Z240, Série MM, Maison mobiles ou CAN/CSA-Z240 VC, Véhicules de camping, ou la norme 24
CFR Part 3280, Manufactured Home Construction and Safety Standard. Si ces normes ne sont pas pertinentes, utilisez la norme ANSI/NCS-
BCS A225.1/NFPA 501A, Manufactured Home Installations Standard, ou ANSI A119.2 ou NFPA 501C Standard for Recreational Vehicles.
Cet appareil doit être utilize uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une maison
préfabriquée ou mobile (É.-U. seulement) installée à demeure si les règlements locaux le permettent. Voir la notice de l'utilisateur pour plus de
renseignements. Cet appareil ne peut pas être utilisé avec d'autres gaz sauf si une trousse de conversion certifiée est fournie.
This vented gas fireplace heater is not for use with air filters. Ne pas utiliser de filtre à air avec ce foyer au gaz à é v a c u a t i o n .
For use with glass doors certified with the appliance only Pour utilisation uniquement avec les portes en verre certifiées avec l'appareil
Electrical supply / Électrique 115VAC, 1.13 A, 60Hz.
NOT FOR USE WITH SOLID FUELS. / NE PAS UTILISER AVEC DU COMBUSTIBLE SOLIDE
FPI Fireplace Products International Ltd. Delta, BC, Canada Made in Canada/Fabrique au Canada 918-840
Minimum Clearances to Combustibles/Degagement
Minimum De Materiaux Combustibles
Minimum ceiling height from top of unit:36”/914mm
Minimum plafond hauteur en haut de l’appareil:
A 6-1/2”/165mm
B 6”/152mm
Minimum clearance of Vent Terminal to Outside Corner & Inside Corner:
with AstroCap 6"/150mm with Dura-Vent Cap 12"/300mm
C 2" / 50mm
E 2"/50mm
Serial No./ No de serie
E
E
A
A
Left Side Wall
Right Side Wall
Vertical
Pipe
A
A
BC
Left Side Wall
Right Side Wall
Horizontal
Pipe
Model/Modele: H35-NG2
Model/Modele:
H35-LP2
355
355
#52 DMS
28,500 Btu/h (8.35 Kw/h)
15,000 Btu/h (4.39 Kw/h)
0-4500 ft/pi (0-1372m)
ÉQUIPÉ A L'UISINE POUR GAZ NATURAL
ÉQUIPÉ A L'UISINE POUR GAZ PROPANE
DUPLICATE SERIAL NO.
For the State of Massachusetts, installation and repair must be done by a plumber or gasfitter licensed in the Commonwealth of
Massachusetts.
For the State of Massachusetts, flexible connectors shall not exceed 36 inches in length.
For the State of Massachusetts, the appliances individual manual shut-off must be a t-handle type valve.
The State of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA720 and a CO alarm with
battery back up in the same room where the gas appliance is installed.

Hampton®H35-2 Direct Vent Freestanding Gas Stove 5
REQUIREMENTS
5.08: Modifications to NFPA-54, Chapter 10
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for
residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than
seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall
be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is
installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery
operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure
served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of
qualified licensed professionals for the installation of hard wired carbon monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon
monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of
thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight
(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The
sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL
OBSTRUCTIONS".
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR
5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by
the Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or
structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the
instructions provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
"special venting systems", the following requirements shall be satisfied by the manufacturer:
1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and
2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions,
all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of
the installation.
MA Code - CO Detector
(for the State of Massachusetts only)

6 Hampton®H35-2 Direct Vent Freestanding Gas Stove
IMPORTANT MESSAGE
SAVE THESE
INSTRUCTIONS
The DirectVentFreestandingGasStovemustbe
installed in accordance with these instructions.
Carefullyreadall the instructionsinthismanual
first. Consult the building authority having
jurisdiction to determine the need for a permit
prior to starting the installation.
Note: Failure to follow the instructions
could cause a malfunction of the
heater which could result in death,
seriousbodilyinjury,and/orproperty
damage. Failure to follow these
instructions may also void your fire
insurance and/or warranty.
Note:Theseinstructionstakeprecedenceover
Simpson Dura-Vent instructions.
SPECIFICATIONS
Fuels: H35-NG2 is approved for use with
natural gas.
H35-LP2 is approved for use
with liquefied petroleum gases
(propane).
Electrical: 120V A.C. system.
Circulation Fan: Variable speed, 125/75.
Log Sets: Ceramic fibre, 7 per set.
Vent System: Coaxial (6-5/8" outer / 4" inner
liner) rigid flue and termination cap.
The efficiency rating of the appliance is a
product thermal efficiency rating determined
under continuous operating conditions and
was determined independent of any installed
system.
INFORMATION FOR
MOBILE /
MANUFACTURED
HOMES
AFTER FIRST SALE
This Hampton®product has been tested and
listed by ITS Testing Services as a Direct Vent
Wall Furnace to the following standards:
CGA-2.17-M91, and ANSI Z21.88b-2007/CSA
2.33b-2007.
This Direct Vent System Appliance must be
installedinaccordancewiththe manufacturer's
installation instructions and the Manufactured
INSTALLATION
Home Construction and Safety Standard, Title
24 CFR, Part 3280, or the current Standard
of Fire Safety Criteria for Manufactured
Home Installations, Sites, and Communities
ANSI/NFPA501A,andwithCAN/CSAZ240-MH
Mobile Home Standard in Canada.
This appliance installation must comply with
themanufacturer'sinstallationinstructionsand
localcodes,ifany.Intheabsenceoflocalcodes
followthecurrentNationalFuelGasCode,ANSI
Z223.1andthecurrentNationalElectricalCode
ANSI/NFPA 70 in the U.S.A., and the current
CAN/CSA B149.1 Gas Installation Code and
the current Canadian Electrical Code CSA
C22.1 in Canada.
This Hampton®Mobile/Manufactured
Home Listed appliance comes factory
equipped with a means to secure the
unit.
This Hampton®Mobile/Manufactured
Homelistedappliance comesequipped
with a dedicated #8 ground lug to which
an 18 gauge copper wire from the steel
chassis ground must be attached.
Thisappliancemayonlybeinstalledin
an aftermarket permanently located,
manufactured (USA only )or mobile
home, where not prohibited by local
codes.
This appliance is only for use with
the type of gas indicated on the
rating plate. This appliance is not
convertible for use with other gases,
unless a certified kit is used.
INSTALLATION AND REPAIRS SHOULD
BE DONE BY A QUALIFIED SERVICE
PERSON. THIS APPLIANCE SHOULD BE
INSTALLED, REPAIRED, INSPECTED BE-
FORE USEAND AT LEAST ANNUALLY BY
A QUALIFIED SERVICE PERSON. MORE
FREQUENTCLEANINGMAYBEREQUIRED
DUETOEXCESSIVELINTFROMCARPET-
ING, ETC. IT IS IMPERATIVE THAT THE
CONTROL COMPARTMENT, BURNERS
AND CIRCULATING AIR PASSAGEWAYS
OF THE APPLIANCE BE KEPT CLEAN.
DUE TO HIGH TEMPERATURES, THE AP-
PLIANCE SHOULD BE LOCATED OUT OF
TRAFFIC AND AWAY FROM FURNITURE
AND DRAPERIES.
BEFORE YOU START
Safeinstallationandoperationofthisappliance
requires common sense, however, we are
required by the Canadian Safety Standards
and ANSI Standards to make you aware of
the following:
1) Provide adequate clearances for servicing,
properoperationandaroundtheairopenings
into the combustion chamber.
2) The appliance must be installed on a flat,
solid,continuoussurface(e.g.wood,metal,
concrete).This maybethefloor,oritcanbe
raiseduponaplatformtoenhanceitsvisual
impact. The appliance may be installed on
carpeting, tile, wood flooring or other com-
bustible material, because the appliance's
baseextends the full width and depth of the
appliance. The Direct Vent Freestanding
GasStovecanbeinstalledinawide variety
of ways and will fit nearly any room layout.
It may be installed in a recessed position,
framed out into the room, or across a cor-
ner.
3) The Direct Vent Freestanding Gas Stove
is approved for alcove installations, which
meet the clearances listed in the "Clear-
ance to Combustibles" section. This unit is
approved for manufactured home installa-
tions, see the "Manufactured Mobile Home
Additional Requirements" section and the
"Venting Arrangement" section for the re-
quiredventarrangements.Ifinstalledintoa
manufacturedhome theunitmustbebolted
down to the floor.
4) ThisapplianceisListedfor bedroom instal-
lations when used with a Listed Millivolt
Thermostat. Some areas may have further
requirements, check local codes before
installation.
5) This appliance is Listed for Alcove installa-
tions,maintainminimumAlcoveclearances
asfollows, minimumwidthof40"(1016mm),
a maximum depth of 36" (914mm), and
minimum ceiling height of 64" (1626mm)
from floor to ceiling.
6) We recommend that you plan your instal-
lation on paper using exact measurements
for clearances and floor protection before
actually installing this appliance. Have a
qualifiedbuildinginspectorreviewyourplans
before installation.
WARNING: FAILURE TO INSTALL THIS
APPLIANCE CORRECTLY WILL VOID
YOUR WARRANTY AND MAY CAUSE A
SERIOUS HOUSE FIRE.
CHILDREN AND ADULTS SHOULD BE
ALERTED TO THE HAZARDS OF HIGH
SURFACETEMPERATURES,ESPECIALLY
THE FIREPLACE GLASS, AND SHOULD
STAYAWAYTOAVOIDBURNSORCLOTH-
ING IGNITION.
YOUNG CHILDREN SHOULD BE CARE-
FULLY SUPERVISEDWHENTHEYAREIN
THE SAME ROOM AS THE APPLIANCE.
CLOTHING OR OTHER FLAMMABLE
MATERIALSHOULDNOTBEPLACEDON
OR NEAR THE APPLIANCE.

Hampton®H35-2 Direct Vent Freestanding Gas Stove 7
INSTALLATION
GENERAL SAFETY
INFORMATION
1) Theapplianceinstallationmustconformwith
local Canadian Electrical Code.
2) The appliance when installed, must be
electrically grounded in accordance with
localcodes,orintheabsenceoflocalcodes
with the current National Electrical Code,
ANSI/NFPA 70 or CSA C22.1 Canadian
Electrical Code.
3) The appliance should be inspected for
shipping damage before use and serv-
iced annually by a professional service
person. More frequent cleaning may be
required due to excessive lint from carpet-
ing, bedding material, etc. It is imperative
that control compartments, and circulating
air passageways of the appliance be kept
clean and free from excessive lint from
carpeting.
4) See general construction and assembly
instructions.Theapplianceandventshould
be enclosed when installed in or passing
through a living area, where children may
come in contact with it.
5) This appliance must be connected to the
specified vent and termination cap to the
outside of the building envelope. Never
vent to another room or inside a building.
Make sure that the vent is fitted as per the
instructions starting in the "Exterior Vent
Terminal Locations" section.
6) Inspect the venting system annually for
blockage and any signs of deterioration.
7) Ventingterminalsshallnotberecessedinto
a wall or siding.
8) Any safety glass removed for servicing
must be replaced prior to operating the ap-
pliance.
9) To prevent injury, do not allow anyone who
is unfamiliar with the operation to use the
fireplace.
INSTALLATION
CHECKLIST
1) Locateyourappliance.Refertothefollowing
sections:
a. Clearances to combustibles
b. Locating Your Gas Stove
c. For venting requirements, see "Venting
Introduction" to "Venting Arrangements"
Section.
2) Install Optional Fan. Refer to the "Optional
Fan Installation" section.
3) Set vent restrictors. Refer to the "Vent Re-
strictor Position" section.
4) Installventing.Refertothefollowingsections
where applicable:
a. Check all venting requirements.
See "Venting Introduction" to "Venting
Arrangements" sections.
b. Vertical Termination with Co-linear Flex
System
c. DV Stove Horizontal Vent Kit
d. Dura-Vent Termination Kit.
5) Make gas connections. Refer to the "Gas
Connection" section
Test the pilot.Mustbeasperdiagram in the
"Maintenance Instruction" section.
If converting to Propane, make changes
priorseethe"Conversionfrom Natural Gas
to Propane" section.
6) Test Gas Pressure. Refer to the "Gas Pipe
Pressure Testing" section.
7) Installstandardandoptionalfeatures. Refer
to the following sections where applicable:
a. Brick Panels
b. Log Set Installation
c. Wall Thermostat
d. Remote Control
e. Optional Side Shelves
8) Finalcheck.Refer tothe"FinalCheck" sec-
tion.
Before leaving this unit with the customer,
the installer must ensure that the appli-
ance is firing correctly and operation fully
explained to customer.
This includes:
1) Clockingtheappliancetoensurethecorrect
firingrate(ratenotedonlabel) afterburning
appliance for 15 minutes.
2) Ifrequired,adjustingtheprimaryairtoensure
that the flame does not carbon. First allow
the unit to burn for 15-20 min. to stabilize.
CAUTION:Anyalteration to theproduct that
causes sooting or carboning that results
in damage is not the responsibility of the
manufacturer.
CLEARANCES TO
COMBUSTIBLES
TheclearanceslistedareMINIMUMdistances.
Measure the clearance to both the appliance
and the chimney connector. The farthest
distance is correct if the two clearances do
not coincide.
Forexample,iftheapplianceis setasindicated
in one of the figures but the connector is too
close,movethestoveuntilthecorrectclearance
to the connector is obtained.
This appliance may be installed only with the
clearances as shown in the situations pictured.
Donotcombine clearancesfromonetypeof
installation with another in order to achieve
closer clearances.
Thisunitcanbeinstalledonasolidcombustible
surface like a wood floor. This unit can also be
installed directly on carpeting or vinyl.
Use the minimum clearances shown in the
diagrams below:
H35-NG2 & H35-LP2 Clearances
A Side Wall to Unit 6-1/2" / 165 mm
B Back Wall to Unit 6" / 152 mm
C Vertical Vent Pipe to Back Wall
2" / 50 mm
E Unit Corner to Wall 2" /50 mm
Unit Top to Alcove Ceiling 36" / 914 mm
Minimum ceiling height is 36" /914 mm from
top of unit.
Emissions from burning wood or gas could
contain chemicals known to the State of Cali-
fornia to cause cancer, birth defects or other
reproductive harm.

8 Hampton®H35-2 Direct Vent Freestanding Gas Stove
OPTIONAL FAN INSTALLATION
Diagram 1
Diagram 2
LOCATING YOUR
GAS STOVE
Whenselectingalocationforyourstove,ensure
thattheclearanceslisted abovearemetaswell
asensuringthatthere is adequate accessibility
for servicing and proper operation.
MANUFACTURED
MOBILE HOME
ADDITIONAL
REQUIREMENTS
1) Ensure that structural members are not cut
or weakened during installation.
2) Ensure proper grounding using the #8
ground lug provided.
3) Appliance must be anchored to the floor
with the supplied anchoring methods.
COMBUSTION AND
VENTILATION AIR
Thecombustionairfromthisapplianceisdrawn
fromoutsidethebuildingthroughtheouterflue.
Extraprovisionforcombustionairinsidethe
room is not required.
A) Cross Corner
B) Room Divider
C) Island
D) Flat on Wall
E) Flat on Wall Corner
F) Flush with Wall/Alcove
For Vent Termination requirements, see the
"Exterior Vent Terminal Locations" section.
Fan Kit Contains:
Qty. Description
1 Fan Speed Controller with nut, and
knob.
1 Fan Assembly c/w green wire
attached
1 Power cord
1 Plastic locking grommet
1) Remove the Top Control Panel Assembly
by removing the three screws. Diagram 1.
2) Removethenylonholeplugfromthecontrol
panel.
3) Install the fan speed controller onto the
control panel and secure with nut. Connect
remaining wire harness wires to speed
control. NOTE: Speed control wires must
be in the down position when control panel
is in place.
4) Push black knob onto speed control.
5) Remove the rear access panel on the back
ofthestovebyremovingthe6screws.Install
the fan onto pins as per Diagram 2.
NOTE: Do NOT damage, cut or remove
the 3" aluminum air intake pipes.
Hint for pushing fan down onto pins - rub a
bitofdishsoaponthepinssothegrommets
will slide down more easily. Check to make
sure the fan is seated properly on the pins
- try to move the fan back and forth.
6) Push power cord through hole in the rear
panel 14" - 16" and tie a loose knot in the
cordontheinsidetopreventthepowercord
from being pulled out. Diagram 2.
7) Install locking grommet to power cord and
pushthroughholeintherearpanelandgive
a 1/4 turn to secure.
NOTE: Whenrunningwires,keepthemclear
ofvalveassemblyandtubingtoavoid
tangling of wires and valve.
NOTE: Becarefulnottocutwireswhenpass-
ing through holes in the firebox.
8) Rungreengroundwirefromfanandconnect
to grounding lug.
9) Connect green power cord ground wire to
grounding lug.
10) Run the neutral black wire from power cord
and connect to fan motor.
11) Runthelive blackwirefrompowercordand
connect to speed control wire.
12) Connect the white wire of the wire harness
to the fan terminal.
NOTE: Pull excess wire next to fan to
avoid excessive heat from the firebox.
13) Ensureallwiresarepulledawayfromfirebox
to avoid excessive heat and secure with
stick-on wire clip.
14) Re-attach control panel with 3 screws, re-
versingstep1.Re-attachrearaccesspanel
with 6 screws, reversing step 5.
NOTE:Whenpowercordispluggedin,speed
control is in the ON position and stove is
burning, allow 10 - 15 minutes for the ther-
modisc(temperatureswitch)toactivateand
turn on the Fan automatically.
WARNING:
Electrical Grounding Instructions
This appliance is equipped with
a three pronged (grounding) plug
for your protection against shock
hazard and should be plugged
directly into a properly grounded
three-prong receptacle. Do not cut
or remove the grounding prong
from this plug.
INSTALLATION

Hampton®H35-2 Direct Vent Freestanding Gas Stove 9
INSTALLATION
INSTALLATION
PRECAUTIONS
Theseventingsystemsareengineeredproducts
that have been designed and tested for use
with the H35-NG2, and H35-LP2. The warranty
will be voided and serious fire, health or other
safety hazards may result from any of the fol-
lowing actions:
1) Installation of any damaged Direct Vent
component
2) UnauthorizedmodificationoftheDirectVent
System
3) Installation of any component part not
approved by FPI - Fireplace Products
International Ltd.
4) Installation other than as instructed by the
approved rigid pipe manufacturers and FPI
Fireplace Products International Ltd.
Warning: Alwaysmaintainrequired
clearances (air spaces) to nearby
combustibles to prevent a fire
hazard. Do not fill air spaces with
insulation.
Besuretochecktheventterminationclearance
requirements from decks, windows, soffits,
gas regulators, air supply inlets and public
walkways as specified in the "Exterior Vent
Terminal Locations" section and in your local
building codes.
The gas appliance and vent system must be
venteddirectlytotheoutsideofthebuilding,
and never be attached to a chimney serving
a separate solid fuel or gas-burning appli-
ance. Each direct vent gas appliance must use
it's own separate vent system. Common vent
systems are prohibited.
SAFETY PRECAUTIONS
FOR THE INSTALLER
1) Wear gloves and safety glasses for protec-
tion.
2) Exercise extreme caution when using lad-
ders or on roof tops.
3) Be aware of electrical wiring locations in
walls and ceilings.
VENTING
INTRODUCTION
The Horizontal Termination Kit and the rigid
pipe venting systems, in combination with the
DirectVentFreestandingGasStoves,H35-NG2
and H35-LP2, have been tested and listed as
directventheatersystemsby WarnockHersey.
Theseunitsusethe"balanced flue" technology
Co-Axialsystem.Theinnerlinerventsproducts
ofcombustiontotheoutsidewhiletheouterpipe
draws outside combustion air into the combus-
tion chamber thereby eliminating the need to
use heated room air for combustion and losing
warm room air up the chimney.
Note: These flue pipes must not be
connected to any other appliance.
The gas appliance and vent system must be
vented directly to the outside of the building,
and never be attached to a chimney serving a
separate solid fuel or gas burning appliance.
Eachdirectventgasappliancemustuseit'sown
separate vent system. Common vent systems
are prohibited.
IMPORTANT
Read all instructions carefully before starting
the installation. Failure to follow these instruc-
tions may create a fire or other safety hazard,
and will void the warranty. Be sure to check the
venting and clearance to combustible require-
ments. Consultyourlocalbuildingcodesbefore
beginning installation.
Thelocationoftheterminationcapmustconform
totherequirementsinthe"ExteriorVentTerminal
Locations" section.
VENT RESTRICTOR
POSITION
Vent restriction is required for certain venting
installations, see the diagrams in "Venting
Arrangement" section to determine if they are
required for your installation.
To set the Vent restriction as indicated in the
diagramsinthe"VentingArrangement"section,
simply loosen the screws and push the vent
restrictor plate to the correct position. Tighten
the screws.
Horizontal Termination:
Vent Restrictor setting at 36,000 Btu/h
Vertical Termination:
Vent Restrictor setting at 36,000 Btu/h

10 Hampton®H35-2 Direct Vent Freestanding Gas Stove
EXTERIOR VENT TERMINAL LOCATIONS
INSTALLATION
Minimum Clearance Requirements Canada1USA2
AClearance above grade, veranda, porch, deck, or balcony 12"(30cm) 12"(30cm)
BClearance to window or door that may be opened 12"(30cm) 9" (23cm)
CClearance to permanently closed window **
DVertical clearance to ventilated soffit located above the terminal within a horizontal distance of 2 feet (61cm)
from the center line of the terminal (check with the local code)
22"(56cm) 22"(56cm)
EClearance to unventilated soffit 12"(30cm) 12"(30cm)
FClearance to outside corner: with AstroCap and Vent Riser Termination Caps 6"(15cm) 6"(15cm)
Clearance to outside corner: with all other approved Termination Caps 12"(30cm) 12"(30cm)
GClearance to inside corner: with AstroCap and Vent Riser Termination Caps 6"(15cm) 6"(15cm)
Clearance to inside corner: with all other approved Termination Caps 12"(30cm) 12"(30cm)
HClearance to each side of center line extended above meter/regulator assembly 36"(90cm)a*
JClearance to service regulator vent outlet 36"(90cm) *
KClearance to non-mechanical air supply inlet to building or the combustion air inlet to any other appliance 12"(30cm) 9" (23cm)
LClearance to a mechanical air supply inlet
#3' (91cm) above if within 10' (3m) horizontally.
72"(1.8m) 36"(90cm)b
MClearance above paved sidewalk or a paved driveway located on public property 84"(2.1m)┼*
NClearance under veranda, porch, deck, or balcony 12"(30cm)‡*
1In accordance with current CSA B149.1, Natural Gas and Propane Installation Code
2In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code
┼A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.
‡ Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor
*Clearance in accordance with local installation codes and the requirements of the gas supplier
a3 feet (91cm) within a height of 15 feet (4.5m) above the meter / regulator assembly
b3 feet (91cm) above - if within 10 feet (3m) horizontally

Hampton®H35-2 Direct Vent Freestanding Gas Stove 11
INSTALLATION
4” X 6-5/8” RIGID PIPE
CROSS REFERENCE CHART ONLY
Components from different Manufacturers may not be mixed. Not All Rigid Pipe components are available directly from FPI.
Description Simpson
Direct Vent Pro®
Selkirk
Direct Temp™
American Metal
Products®
Amerivent Direct
Metal-Fab™
Sure Seal
Security
Secure- Vent®
ICC Excel
Direct
6” Pipe Length-Galvanized 46DVA-06 4DT-6 N/A 4D6 SV4L6 TC-4DL6
6” Pipe Length-Black 46DVA-06B 4DT-6B N/A 4D6B SV4LB6 TC-4DL6B
7” Pipe Length-Galvanized N/A N/A 4D7 N/A N/A N/A
7” Pipe Length-Black N/A N/A 4D7B N/A N/A N/A
9” Pipe Length-Galvanized 46DVA-09 4DT-9 N/A N/A N/A N/A
9” Pipe Length-Black 46DVA-09B 4DT-9B N/A N/A N/A N/A
12” Pipe Length-Galvanized 46DVA-12 4DT-12 4D12 4D12 SV4L12 TC-4DL1
12” Pipe Length-Black 46DVA-12B 4DT-12B 4D12B 4D12B SV4LB12 TC-4DL1B
18” Pipe Length-Galvanized 46DVA-18 4DT-18 4D18 4D18 SV4LA TC-4DL18
18” Pipe Length-Black 46DVA-18B 4DT-18B 4D18B 4D18B SV4LA TC-4DL18B
24” Pipe Length-Galvanized 46DVA-24 4DT-24 4D24 4D24 SV4L24 TC-4DL2
24” Pipe Length-Black 46DVA-24B 4DT-24B 4D24B 4D24B SV4LB24 TC-4DL2B
36” Pipe Length-Galvanized 46DVA-36 4DT-36 4D36 4D36 SV4L36 TC-4DL3
36” Pipe Length-Black 46DVA-36B 4DT-36B 4D36B 4D36B SV4LB36 TC-4DL3B
48” Pipe Length-Galvanized 46DVA-48 4DT-48 4D48 4D48 SV4L48 TC-4DL4
48” Pipe Length-Black 46DVA-48B 4DT-48B 4D48B 4D48B SV4LB48 TC-4DL4B
60” Pipe Length-Galvanized 46DVA-60 4DT-60 N/A N/A N/A N/A
60” Pipe Length-Black 46DVA-60B 4DT-60B N/A N/A N/A N/A
Adjustable Length 3”-10”-Galvanized N/A N/A N/A 4DAL N/A TC-4DLT
Adjustable Length 3”-10”-Black N/A N/A N/A 4DALB N/A TC-4DLTB
Adjustable Length 7”-Galvanized N/A N/A 4D7A N/A N/A N/A
Adjustable Length 7”-Black N/A N/A 4D7AB N/A N/A N/A
Extension Pipe 8-1/2”-Galvanized 46DVA-08A N/A N/A N/A N/A N/A
Extension Pipe 8-1/2”-Black 46DVA-08AB N/A N/A N/A N/A N/A
Adjustable Length 12”-Galvanized N/A N/A 4D12A N/A SV4LA12 N/A
Adjustable Length 12”-Black N/A N/A 4D12A N/A SV4LBA12 N/A
Extension Pipe 16”-Galvanized 46DVA-16A N/A N/A N/A N/A N/A
Extension Pipe 16”-Black 46DVA-16AB N/A N/A N/A N/A N/A
45ºElbow-Galvanized 46DVA-E45 4DT-EL45 4D45L N/A N/A TE-4DE45
45ºElbow-Black 46DVA-E45B 4DT-EL45B 4DT-EL45B N/A N/A TE-4DE45B
45ºElbow Swivel-Galvanized See 46DVA-E45 N/A N/A 4D45L SV4E45 N/A
45ºElbow Swivel-Black See 46DVA-E45B N/A N/A 4D45LB SV4EB45 N/A
90ºElbow-Galvanized 46DVA-E90 4DT-EL90S 4DT-EL90S N/A N/A TE-4DE90
90ºElbow-Black 46DVA-E90B 4DT-EL90SB 4DT-EL90SB N/A SV4EBR90-1 TE-4DE90B
90ºElbow, Swivel-Galvanized See 46DVA-E90 N/A N/A 4D90L SV4E90-1 N/A
90ºElbow, Swivel-Black See 46DVA-E90B N/A N/A 4D90LB SV4EB90-1 N/A
90º Starter Elbow, Swivel-Galvanized N/A N/A N/A 4D90A N/A N/A
Adaptor* N/A N/A N/A 4D90L N/A N/A
Ceiling Support N/A 4DT-CS 4DFSP 4DSP SV4SD TE-4DE45
Cathedral Support Box 46DVA-CS 4DT-CSS 4DRSB 4DRS SV4CSB TE-4DE45B
Wall Support/Band 46DVA-WS 4DT-WS/B 4DWS 4DWS SV4BM N/A
Offset Support 46DVA-ES (N/A - FPI) 4DT-OS N/A N/A SV4SU N/A
Wall Thimble-Black 46DVA-WT 4DT-WT 4DWT 4DWT SV4RSM TE-4DE90
Wall Thimble Support/Ceiling Support 46DVA-DC N/A N/A N/A SV4PF TE-4DE90B
Firestop Spacer 46DVA-FS 4DT-FS 4DFSP 4DFS SV4BF N/A
Trim Plate-Black N/A 4DT-TP 4DFPB 4DCP SV4LA N/A

12 Hampton®H35-2 Direct Vent Freestanding Gas Stove
INSTALLATION
Description Simpson
Direct Vent Pro®
Selkirk
Direct Temp™
American Metal
Products®
Amerivent Direct
Metal-Fab™
Sure Seal
Security
Secure- Vent®
ICC Excel
Direct
Attic Insulation Shield 12” 46DVA-IS N/A@ FPI N/A 4DAIS12 N/A SV4RSA N/A
Attic Insulation Shield - Cold Climates 36” N/A N/A 4DAIS12 N/A N/A TM-4AS
High Wind Vertical Cap 46DVA-VCH N/A N/A N/A N/A TM-4VT
High Wind Horizontal Cap 46DVA-HC N/A N/A N/A N/A TM-4DHT
Horizontal Square Termination Cap See 46DVA-HC 4DT-HHC 4DHC 4DHT SV4CHC-1 TM-4HT
Vertical Termination Cap 46DVA-VC 4DT-HVC 4DVC 4DVT SV4CGV-1 TM-4VT
Storm Collar 46DVA-08A 4DT-SC 4DSC 4DSC SV4FC TM-SC
Restrictor Disk 46DVA-RD N/A N/A N/A N/A TM-4DS
Extended Vertical Termination Cap 46DVA-VCE N/A N/A N/A N/A N/A
Chimney Conversion Kit A (USA only) 46DVA-KCA N/A N/A N/A N/A TM-4CA6
Chimney Conversion Kit B (USA only) 46DVA-KCB N/A N/A N/A N/A TM-4CA7
Chimney Conversion Kit C (USA only) 46DVA-KCC N/A N/A N/A N/A TM-4CA8
Chimney Conversion Kit Masonry
(USA only)
46DVA-KMC N/A N/A N/A N/A N/A
Wall Firestop 46DVA-WFS N/A N/A N/A N/A TM-4TR
Colinear Flex Connectors 46DVA-ADF N/A N/A N/A N/A N/A
Adjustable Flashing 0/12-6/12 N/A 4DT-ST14 4D12S 4DST14 SV4STC14 TF-4FA
Adjustable Flashing 6/12-12/12 N/A 4DT-ST36 4D36S 4DST36 SV4STC36 TF-4FB
Vinyl Siding Standoff 46DVA-VSS 4DT-VS N/A 4DVS SV4VS TM-VSS
Vinyl Siding Shield Plate N/A 4DT-VSP N/A N/A SV4VS N/A
Snorkel Termination 14” 46DVA-VCH N/A N/A N/A N/A TM-4ST14
Snorkel Termination 36” 46DVA-HC N/A N/A N/A N/A TM-4ST36
Basic Horizontal Termination Kit (A) Disc. 4DT-HKA 4DHTK2 4DHTKA SV-SHK N/A
Horizontal Termination Kit (B) 46DVA-KHA
(Changed Components)
4DT-HKB 4DHTK1 4DHTKB SV-HK N/A
Vertical Termination Kit Disc. 4DT-VKC 4DHTK 4DHTK SV-FK N/A
FPI
946-506/P Vent Guard (Optional) for AstroCap 946-205 Vinyl Siding Shield for Riser Vent Terminal
510-994 Rigid Pipe Adaptor (Must use with all rigid piping) 946-208/P Vent Guard (Optional) for Riser Vent Terminal
640-530/P Riser Vent Terminal 946-523/P AstroCap Horizontal Cap
946-206 Vinyl Siding Standoff for AstroCap
Note: When using Metal-Fab Sure Seal Rigid Piping - please note that the Adaptor (4DDA) must be used in conjunction with FPI Rigid Pipe Adaptor (510-994).
Note: Horizontal runs of vent must be level, or have a 1/4” rise for every 1 foot of run towards the termination.
Never allow the vent to run downward - this could cause high temperatures and may present a possible fire hazard.
Offset Pipe Selection: Use this table to determine offset pipe lengths.
Pipe Length
(L)
4” x 6-5/8” Venting For specific instructions on venting components - visit the
manufacturers website listed below.
Run (X) Rise (Y)
0” (0mm) 4-7/8” (124mm) 13-7/8” (340mm) Simpson Direct Vent Pro: www.duravent.com
6” (152mm) 8” (203mm) 16-1/2” (419mm) Selkirk Direct-Temp: www.selkirkcorp.com
9” (229mm) 10-1/8” (257mm) 18-5/8” (473mm) American Metal Products: www.americanmetalproducts.com
12” (305mm) 12-1/4” (311mm) 20-3/4” (527mm) Metal-Fab Sure Seal: www.mtlfab.com
24” (610mm) 20-5/8” (524mm) 29-1/8” (740mm) Security Secure Vent: www.securitychimneys.com
36” (914mm) 29” (737mm) 37-1/2” (953mm) Industrial Chimney Company: www.icc-rsf.com
48” (1219mm) 37-7/16” (951mm) 45-15/16” (1167mm)

Hampton®H35-2 Direct Vent Freestanding Gas Stove 13
RIGID PIPE VENTING SYSTEMS
Horizontal or Vertical Terminations
INSTALLATION
Alternate
Horizontal
Termination
Caps
The FPI AstroCapTM and FPI Riser Vent terminal are certified for installations using FPI venting systems as well as Simpson Dura-Vent®Direct Vent Pro,
American Metal Products Ameri Vent Direct Vent, Security Secure Vent®, Selkirk Direct-Temp. AstroCapTM is a proprietary trademark of FPI Fireplace
Products International Ltd. Dura-Vent® and Direct Vent Pro are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.
This product has been evaluated by Intertek
for use with Duravent Direct-Vent Pro, Selkirk
Direct-Temp, Ameri Vent Direct venting and
Security Secure Vent systems.
WARNING:
Do not combine venting components from
different venting systems.
However use of the the AstroCapTM and FPI
Riser is acceptable with all systems.
When using Rigid Vent other than
Simpson Dura-Vent, 3 screws must be
used to secure rigid pipe to adaptor.

14 Hampton®H35-2 Direct Vent Freestanding Gas Stove
INSTALLATION
Offset to Vertical Terminations
VENTING ARRANGEMENTS
Vertical Terminations Systems for
Residential Manufactured and Mobile Homes
Theshadedarea inthediagram belowshowsall allowablecombinationsof straight vertical
and offset to vertical runs with vertical terminations. Maximum two 45oelbows.
If the vent is ENCLOSED in a chase (min. size 9" x 9") maintain a 1-1/4" clearance to combus-
tibles. May be installed in Manufactured (Mobile) Homes after first sale.
Horizontal Terminations for All
Venting Systems
The shaded areas in the diagram below show
allallowablecombinationsofverticalrunswith
horizontal terminations. Maximum one 90O
elbow (two 45o elbows equal one 90oelbow).
All approved caps listed on page 12 - may
be used.
Propane and Natural Gas:
Residential, Manufactured and
Mobile Homes Installations
The venting arrangements diagrammed below,
haveamin.of75%(flueloss)efficiencywithFan
Off,asrequiredformanufacturedhomes.(Actual
efficiency may be as high as 85%)
May be installed in Manufactured (Mobile)
Homes after first sale.
ROTATING 45OELBOW FOR STRAIGHT HORIZONTAL TERMINATIONS
1)Removeall4screwsthatsecure
the elbow to the unit using a 1/4"
magnetic nut driver.
2) Rotate the elbow 180o
3) Secure the elbow by securing
it with the 4 screws.
Remove all 4 screws
and washers
NOTE: See "Vent Restrictor Position" section for
installation instructions for the Vent Restrictor
Position.

Hampton®H35-2 Direct Vent Freestanding Gas Stove 15
VENTING ARRANGEMENTS
HORIZONTAL TERMINATIONS USING RIGID PIPE
Snorkel Termination Riser Vent Termination
The two diagrams show all allowable com-
binationsofstraight horizontal termination
using Rigid Pipe. Restrictor position "A".
Only a snorkel or FPI Riser vent may be
used as shown. No other termination cap
is permitted.
Venting Arrangements -Straight Horizontal Termination at a De-Rated BTU
The diagrams show all allowable combina-
tionsofstraighthorizontalterminationusing
Rigid Pipe. Restrictor position "A". Refer to
the "Conversion Kit to Lower BTU Rating"
section for de-rating instructions.
Note: If venting this appliance as per the
diagrams shown in the two diagrams, the unit
"must" be derated using part #740-950 for NG
and part #740-952 for LP. Refer to the conver-
sion kit to lower BTU rating section for derating
instructions.
Also, only a snorkel or FPI Riser vent may be
usedasshowninthenoteddiagrams. Noother
termination cap is permitted.
Dangerous operating conditions will occur
if these instructions are not adhered to.
INSTALLATION
*Ifthisis anoutside corner,the minimumdis-
tancebetweentheventandtheoutsidecorner
is 6” (15cm). See “F” on the diagram in the
"Exterior Vent Terminal Locations" section.
Snorkel Termination Riser Vent Termination

16 Hampton®H35-2 Direct Vent Freestanding Gas Stove
Horizontal Venting with Two (2) 90oElbows
Option V H + H1
A) 3' Min. 2' Max.
B) 4' Min. 3' Max.
C) 5' Min. 4' Max.
D) 6' Min. 5' Max.
E) 7' Min. 6' Max.
F) 8' Min. 8' Max.
Horizontal Venting with Two (2) 90oElbows
Option H V H + H1
A) 1' Max. 2' Min. 3' Max.
B) 2' Max. 3' Min. 5' Max.
C) 3' Max. 5' Min. 6' Max.
D) 4' Max. 7' Min. 7' Max.
E) 5' Max. 9' Min. 8' Max.
With these options, max.
total pipe length is 30 feet
with min. of 9 feet total
vertical and max. 8 feet
total horizontal.
Please note min. 1 foot
between 90oelbows is
required.
With these options, maxi-
mum total pipe length is 30
feet with minimum of 8 feet
totalverticalandmaximum
8 feet total horizontal.
Please note minimum 1
foot between 90oelbows
is required.
INSTALLATION
One 90oelbow = Two 45oelbows.
One 90oelbow = Two 45oelbows.
Vent restrictor position A (fully open), refer to the
"Vent Restrictor Position" section.
Vent restrictor position A (fully open), refer to the "Vent
Restrictor Position" section.
H1
H
V
Lengths do not include elbow indicated
Lengths do not include elbow indicated

Hampton®H35-2 Direct Vent Freestanding Gas Stove 17
H1
H
V
Vertical Venting with Two (2) 90oElbows
Option V H V + V1
A) 1' Min. 3' Max. 2' Min.
B) 2' Min. 4' Max. 3' Min.
C) 3' Min. 5' Max. 4' Min.
D) 4' Min. 6' Max. 5' Min.
E) 5' Min. 7' Max. 6' Min.
Vertical Venting with Two (2) 90oElbows
Withtheseoptions, max.total
pipelengthis30feetwithmin.
of6feettotalverticalandmax.
7 feet total horizontal.
Please note min. 1 foot
between 90oelbows is
required.
Option H + H1 V
A) 2' Max. 2' Min.
B) 3' Max. 3' Min.
C) 4' Max. 4' Min.
D) 5' Max. 5' Min.
E) 6' Max. 6' Min.
Withtheseoptions,max.total
pipelengthis30feetwithmin.
of6feettotalverticalandmax.
6 feet total horizontal.
Please note min. 1 foot
between 90oelbows is
required.
INSTALLATION
One 90oelbow = Two 45oelbows.
One 90oelbow = Two 45oelbows.
Vent restrictor position A (fully open), refer to the "Vent Re-
strictor Position" section.
Vent restrictor position A (fully open), refer to the
"Vent Restrictor Position" section.
Lengths do not include elbow indicated
Lengths do not include elbow indicated

18 Hampton®H35-2 Direct Vent Freestanding Gas Stove
Venting Arrangements - Vertical Terminations
with Co-linear Flex System for both
Residential & Manufactured Homes
into Masonry Fireplaces
The shaded area in the diagram shows the allowable vertical
terminations. Note: Must remove 4 screws from stove collar
androtate 180oto havecollar facingstraightback. Secureinto
place with 4 screws.
VERTICAL TERMINATION WITH CO-LINEAR FLEX SYSTEM
THE APPLIANCE MUST NOT BE
CONNECTED TO A CHIMNEY FLUE
SERVING A SEPARATE SOLID FUEL
BURNING APPLIANCE.
This appliance is designed to be attached to
two 3" (76mm) co-linear aluminium flex running
the full length of the chimney. See the Venting
Arrangements chart below for minimum and
maximum flue lengths. See chart below for
minimumdistancesfromroof.Periodicallycheck
that the vent is unrestricted.
Masonrychimneysmaytakevariouscontours whichtheflexible linerwillaccommodate. However,
keep the flexible liner as straight as possible, avoid unnecessary bending.
The Air Intake pipe must be attached to the inlet air collar of the termination cap.
Straight Vertical Terminations
INSTALLATION
Required Parts:
Part # Description
946-529 Co-linear DV Vertical
Termination Cap
948-305 3" Flex - 35 ft.
946-563 Co-Axial to Co-Linear Adaptor Kit
which contains the following:
Co-linear Flex Adaptor (270-585)
Outer Pipe (946-257)
Inner Pipe Adaptor (946-219)
Vent Restrictor
setat1-3/4"open
(fully open),
Position "A"

Hampton®H35-2 Direct Vent Freestanding Gas Stove 19
Review the following sequence of instructions
which are typical of most installations. The se-
quence may vary depending on wall thickness.
See "Exterior Vent Terminal Locations" to
"Venting Arrangements" section for vent
locationandclearancedimensions, and the
"Vent Restrictor Position" section to set the
Vent Restrictor to the correct position.
1) Set the unit in its desired location. Check
to determine if wall studs will be in the way
of the venting system, adjust location until
all clearances are met and there are no
obstructions.
Note: A1-1/2"(38mm)clearancearoundthe
outerpipemustbemaintainedexcept
that only a 1" (25mm) clearance is
needed at the termination end.
IMPORTANT:
Do not locate termination hood
where excessive snow or ice
buildupmayoccur.Besuretocheck
vent termination area after snow
falls,andcleartopreventaccidental
blockage of venting system. When
using snow blowers, make sure
snow is not directed towards vent
termination area.
b) Install wall thimbles on both interior
and exterior wall with 4 wood screws
(#8 x 1") per thimble.
c) Attachthe2pieceadjustablepipesec-
tion to the vent terminal and slide into
position from the exterior. The larger
diameterend oftheadjustablepipe
goes to the vent terminal.
d) Install the 90oelbow onto the adjust-
able pipe to determine the vertical
centerline.
Note:ifthecenterlinecannotbemet,
theadjustablesections will have to
be cut.
e) Cut the 4 ft. section of rigid pipe to
length. Attach the 45oelbow to the
rigid pipe, and ensure that the pipe
length when cut (with the 45oelbow)
willseatontoboththestartercollarand
the 90oelbow. Crimped section of
rigid pipe seats into the 90oelbow.
Onlycuttheuncrimpedsideofpipe.
Dismantle all pipe sections including vent
terminal.
2) Assembleatrialfittodeterminethevertical
center-line for the vent termination.
a) Cut a 9-1/2" x 9-1/2" (241mm x 241
mm) square hole on both the interior
and exterior wall.
INSTALLATION
DV STOVE HORIZONTAL TERMINATION VENT KIT
DV 2 ft. Stove Vent Kit (Part # 946-116) and DV 4 ft. Stove Vent Kit (Part #946-216) includes all the parts
needed to install the H35 Direct Vent unit with minimum horizontal and vertical vent dimensions. For
installations that require longer vertical and/or horizontal vents use the Dura-Vent system as shown
in the "Dura-Vent Termination Kit" and "Dura-Vent Venting Components" sections.
Qty. Description
1) 1 Rigid Pipe Section (Kit # 946-116: 2 ft. (1.2m) length,
Kit # 946-216: 4 ft. (1.2m) length), 6-1/2" (165mm)
inside diameter
2) 1 Flex Liner, compressed aluminium 2 ply liner, 4" (102mm)
inside diameter
3) 4 Spring Spacers
4) 1 90 deg. Elbow
5) 1 Adjustable pipe section 13-1/2" to 24" (343mm x 610mm), 2 pcs.
6) 1 Thimble Cover
7) 1 Wall Thimble (2 pcs.)
8) 1 Adaptor
9) 1 AstroCap Termination Cap
10) 2 Trim Collars
11) 1 Tube of Mill-Pac, high temperature sealant
12) 12 Screws, #8 x 1/2" Self tapping, Stainless Steel
13) 14 Screws, #8 x 1/2" Self tapping, Black
14) 4 Screws #8 x 1-1/2" Drill Point, Black
15) 4 Screws #8 x 1-1/2" Drill Point, Stainless Steel
16) 8 Wood screws #8 x 1"
Required but not included in above Kit:
45oElbow (Part #: 946-214)
Note:
a) Liner sections should be con-
tinuous without any joints or
seams.
b) This is an approved system,
therefore components in this
systemmustnotbesubstituted
for any other manufacturer's
products.
DV STOVE HORIZONTAL VENT KIT (#946-116 & #946-216) INSTALLATION