Hanil Combi 508 User manual

Quick Guide Combi 508
Cat. No. : CB-508
Combi 508
2 31
5 64
8 97
0
±
VIEW
SETTINGS
xg
Start Stop Lid Open
Setting Time
Up to < 2 hr
Continuous run (00:00)
Max. RPM : 8,000 rpm
Max. RCF : 8,279 xg
Setting ACC / DEC Rate
ACC (0 ~ 9 steps, Max.9)
DEC (0 ~ 9 steps, Natural DEC.0)
Program Save / Call
Saving a program
(up to 100)
Calling up a program
Setting the Rotor ID
manually
When rotor id is not identified
automatically, enter the rotor ID.
manually
Display Screen
Status of RPM / RCF / Time /
Rotor ID / ACC / DEC / Program
Setting Speed
Press once : Setting RPM
Press twice : Setting RCF
View Settings
Verifying the setting parameters during
centrifugation
Display & Control Panel
Saving / Calling Up
a Program
Setting Run Parameters
(RPM / RCF / Time / ACC / DEC)
Press a parameter
to be changed
Enter the desired value
on the keypad
Press the
Enter button
Press the
Enter button
Enter the desired program
number on the keypad
Press the
Save or call button
Serial No. Installation Date

Connect the device to voltage souces, which
correspond to the power requirements on the
label attached to the device.
Check the wall outlet is earth-
grounded, surge- protected and
can supply enough power.
Check the Line Voltage Grounded Outlet Switch Off the Device
Switch off the device after use.
Unplug the power plug before cleaning or unused
for a long period of time.
Quick Guide Combi 508
Cat. No. : CB-508
30 cm
30 cm
30 cm
A0.2-48 48 x 0.2 ml / Max. 8k
A2.0-24 24 x 1.5/2.0 ml / Max. 8k
A2.0-36 36 x 1.5/2.0 ml / Max. 8k
A10-12 12 x 10 ml / Max. 8k
A15-12 12 x 15 ml / Max. 8k
A15c-12 12 x 15 ml conical / Max. 8k
A50-6 6 x 50 ml / Max. 8k
A50c-6 6 x 50 ml conical / Max. 8k
A50-8 8 x 50 ml / Max. 8k
A85-6 6 x 85 ml / Max. 8k
S750-4 4 x 750 ml / Max. 4k
S500-4 4 x 500 ml / Max. 4k
Emergency Lid Open
If the centrifuge lid cannot be opened, insert the provided
T-wrench into the emergency release hole in the front of the
device and turn it clockwise. (Before activating emergency open,
switch off the device and wait for the rotor to stop.)
Swing-out RotorsFixed-angle Rotors
Maintenance of Swing-Out Rotor
Spread the grease lightly on the bucket
where it contacts the rotor and the pivot.
Clean the chamber and rotor by wiping with
a cloth soaked in mild detergent and dry
completely.
Cleaning
After using the rotor, remove the lid and
keep it upside down. At this time, be careful
not to damage the rotor ID disc.
Rotor Stoarage
1.0KVA
220~240V 50/60Hz
Rev.0
Proudly made by Jiyoung Shim, Hyewon Jeong
Order & Inquiry l [phone] l [email protected] l www.ihanil.com
Service l [phone] l [email protected]
Before Operation After Operation
After relocating the device or loading the ro-
tor, balance them by using a leveler.
If necessary, level the device by adjusting the
‘Leveling foot’ on the bottom of the device.
Balancing the Centrifuge and Rotor
Check the rotor, buckets and tubes are free of
scratch and crack before operation.
Check the Accessories for Abnormalities
Check the rotor is firmly tightend
onto the motor shaft.
Check the Rotor Locking
Load tubes symmetrically into the rotor with
identical amount.
Load Tubes Symmetrically
Rotors
Maintenance
Electrical Safety
Cautions for Use
Allow a safety clearance of 30 cm around the
centrifuge during operation.
Allow a Safety Clearance of 30 cm