Hanna Instruments HI 9813-5 User manual

1
Instruction Manual
HI9813-5 & HI9813-6
Portable
pH/EC/TDS/°C Meters
www.hannainst.com

2
Dear Customer,
Thank you for choosing a Hanna Instruments product.
Please read this instruction manual carefully before using the meter.
This manual will provide you with the necessary information for correct
use of the instrument, as well as a precise idea of its versatility. If you
need additional technical information, do not hesitate to e-mail us at
[email protected].
WARRANTY ..................................................................................2
PRELIMINARY EXAMINATION .........................................................3
GENERAL DESCRIPTION.................................................................3
FUNCTIONAL DESCRIPTION OF HI9813-5 .....................................4
FUNCTIONAL DESCRIPTION OF HI9813-6 .....................................5
SPECIFICATIONS ..........................................................................6
OPERATIONAL GUIDE....................................................................7
pH CALIBRATION..........................................................................9
pH VALUES AT VARIOUS TEMPERATURES.....................................10
EC/TDS CALIBRATION..................................................................11
BATTERY REPLACEMENT..............................................................12
PROBE MAINTENANCE ................................................................12
ACCESSORIES.............................................................................14
WARRANTY
TABLE OF CONTENTS
HI9813-5 and HI9813-6 are guaranteed for two years against defects
in workmanship and materials when used for their intended purpose
and maintained according to instructions. Electrodes and probes
are guaranteed for six months. This warranty is limited to repair or
replacement free of charge.
Damage due to accidents, misuse, tampering or lack of prescribed
maintenance is not covered.
If service is required, contact your local Hanna Instruments Office.
If under warranty, report the model number, date of purchase, serial
number and the nature of the problem. If the repair is not covered by the
warranty, you will be notified of the charges incurred. If the instrument
is to be returned to Hanna Instruments, first obtain a Returned Goods
Authorization number from the Technical Service department and then
send it with shipping costs prepaid. When shipping any instrument,
make sure it is properly packed for complete protection.

3
HI9813-5 and HI9813-6 are complete, versatile and splash-proof
portable combination meters designed with the utmost precision and
simplicity. Both models provide measurements of pH, EC and TDS
ranges, which can be easily selected using a membrane keypad on
the front panel.
Conductivity measurements are automatically compensated for
temperature changes with a built-in temperature sensor. The
temperature coefficient is fixed at 2%/°C.
• HI9813-5 is a pH/EC/TDS meter designed for simplicity of use in
taking pH, mS/cm, ppm and temperature in the °C scale measure-
ments. Suited for hydroponics, greenhouses, farming and ground
water applications.
• HI9813-6 is the most advanced model, including the CAL CheckTM
feature, which allows the user to easily check the probe calibration
status at any time.
Remove the instrument from the packing material and examine
it carefully to make sure that no damage has occurred during
shipment. If noticeable damage is found, please contact your local
Hanna Instruments Office.
Each meter is supplied with:
• Combination probe with 8-pin DIN connector & 1 m (3.3’) cable:
• HI1285-5, pH/EC/TDS/°C probe, for HI9813-5
• HI1285-6, pH/EC/TDS/°C probe with CAL CheckTM for HI9813-6
•HI70007 pH7.01 sachet, 1 pc.
•HI70031 1413 µS/cm (1.413 mS/cm) sachet, 1 pc.
•HI70442 1500 ppm sachet, 1 pc.
•HI700661 cleaning solution sachet, 2 pcs.
•HI50021 check solution sachet, 2 pcs. (for HI9813-6 only)
•Instruction manual
• 1 x 9V alkaline battery.
Note:Save all packing material until you are sure that the instrument
functions correctly. Any defective items must be returned in the
original packing together with the supplied accessories.
PRELIMINARY EXAMINATION
GENERAL DESCRIPTION
All rights are reserved. Reproduction in whole or in part is prohibited without
the written consent of the copyright owner.

4
1) 8-pin DIN connector for probe
2) Liquid Crystal Display
3) pH range selection key
4) mS/cm (EC) range selection key
5) ppm (TDS) selection key
6) pH offset calibration knob
7) EC/TDS calibration knob
8) °C (Temperature) selection key
9) On/Off key
FUNCTIONAL DESCRIPTION OF HI9813-5

5
1) 8-pin DIN connector for probe
2) Liquid Crystal Display
3) pH range selection key
4) mS/cm (EC) range selection key
5) ppm (TDS) range selection key
6) pH offset calibration knob
7) EC/TDS calibration knob
8) °C (Temperature) selection key
9) Check key
10) On/Off key
FUNCTIONAL DESCRIPTION OF HI9813-6

6
Range
0.0 to 14.0 pH
0.00 to 4.00 mS/cm
0 to 1999 ppm
0.0 to 70.0 °C
Resolution
0.1 pH
0.01 mS/cm
1 ppm
0.1 °C
Accuracy
(@ 20 °C/68 °F)
±0.1 pH
±2% f.s. mS/cm
±2% f.s. ppm
±0.5 °C
Typical EMC
Deviation
±0.1 pH
±2% f.s. mS/cm
±2% f.s. ppm
±0.5 °C
Conversion Factor variable, 0.56 to 0.78=1µS/cm
(according with TDS442 curve)
pH Calibration Manual, 1-point through offset
trimmer
EC/TDS Calibration Manual, 1-point through slope
trimmer
EC/TDS Tempera-
ture Compensation
Automaticfrom0to70°C(32to158°F)
with b=2%/°C
Probe (included) HI1285-5 for HI9813-5
HI1285-6 for HI9813-6
Battery Type 1 x 9V alkaline
Battery Life
Environment
Dimensions
Weight 230 g (8.1 oz.)
SPECIFICATIONS

7
INITIAL PREPARATION
Each meter is supplied complete with a 9V battery. Remove the battery
compartment cover on the back of the meter and install the battery
while observing its polarity.
Connect the probe to the DIN socket on the top of the meter by aligning
the pins with the socket and pushing in the plug.
Always remove the probe protective cap before taking any measurements
or calibrating, and stir briefly the electrode in tap water to remove the
storage solution. Make sure the meter has been calibrated.
Turn the meter on by pressing the On/Off key.
TAKING pH MEASUREMENTS
If the probe has been left dry, soak the tip in HI70300 storage solution
for 30 minutes to reactivate it.
• To take a pH measurement simply
submerge the tip (4 cm/ 1½”) of the
probe into the sample to be tested.
• Select the pH mode.
• Stir briefly and wait a couple of
minutes for the reading to adjust
and stabilize. The display shows the
pH value.
• If measurements are taken in different samples successively, it is
recommended to rinse (clean) the probe thoroughly to eliminate
cross-contamination. After cleaning, it is recommended to rinse the
probe with some of the next sample to be measured.
TAKING EC/TDS MEASUREMENTS
• Immerse the tip of the probe (4cm/1½”) into the
sample to be tested. If possible, use plastic beakers
or containers to minimize any EMC interference.
• Tap the probe lightly on the bottom of the beaker
to remove any air bubbles which may be trapped
inside the tip.
OPERATIONAL GUIDE

8
• Select the appropriate measurement range (EC or TDS).
• Wait for a couple of minutes for the
temperature sensor to reach thermal
equilibrium. The display then shows the
measurement automatically compensat-
ed for temperature with the appropriate
following indication: “mS” tag indicates
the meter is in EC mode, while “ppm”
tag indicates the meter is in TDS mode.
TAKING TEMPERATURE MEASUREMENTS
• Submerge the tip (4 cm/ 1½”) of the
probe into the sample to be tested.
• Select the °C mode.
• Stir briefly and wait a couple of minutes
for the reading to adjust and stabilize.
The display shows the temperature
value.
Notes: • If the display shows only a “1”
on the far left hand side, the
reading is out of range.
• It is recommended to clean
often the probe with HI700661
Cleaning Solution.
• After measurements have been completed, the instrument
should be switched off, and the probe cleaned and covered
with the protective cap.

9
For greatest accuracy, frequent calibration of the instrument is recom-
mended. The instrument should be recalibrated for pH:
a) Whenever the electrode is replaced.
b) At least once a month.
c) After testing aggressive chemicals.
d) Where extreme accuracy is required.
e) Whenever the CAL CHECK test fails (HI9813-6 only).
PREPARATION
Pour small quantities of pH7.01 (HI7007) or pH4.01 (HI7004) or
pH10.01 (HI7010) solution into a clean beaker.
To obtain accurate readings, use pH7.01 (HI7007) if you are going
to measure neutral or close to neutral samples, pH4.01 (HI7004) if
you are going to measure acidic samples or pH10.01 (HI7010) for
alkaline measurements.
If you need to calibrate to NIST standards, use pH6.86 (HI7006) instead
of pH7.01 and pH9.18 (HI7009) instead of pH10.01.
PROCEDURE
• Connect the probe and switch the meter on, then press the pH key
to display pH measurement.
•Remove the protective cap from the probe, rinse and immerse it in
the buffer and stir gently. Wait a couple of minutes for the reading
to stabilize.
• Take the temperature of the buffer solution, e.g.
10.0 °C, as follow: select the °C mode and read
the displayed value.
• Adjust the pH calibration knob until
the LCD shows the pH value at the
above temperature (see the pH versus
temperature chart).
• The pH calibration is now complete.
Notes: • The probe should be submerged approximately 4 cm (1½”)
into the solution. The thermometer has to be located close
to the probe.
• If turning the knob the needed value can not be reached,
clean the probe (see the “Probe Maintenance” section). If
also after the probe cleaning the value can not be reached,
replace the probe.
pH CALIBRATION

10
For temperature compensation during calibration, please refer to the
following chart.
pH VALUES AT VARIOUS TEMPERATURES
For instance, if the buffer temperature is 25 °C, the display should
show pH4.0 or 7.0 or 10.0.
If the buffer temperature is 10 °C, the display should show pH4.0 or
7.0 or 10.1.
TEMP pH VALUES
°C °F 4.01 6.86 7.01 9.18 10.01
0 32 4.01 6.98 7.13 9.46 10.32
5 41 4.00 6.95 7.10 9.39 10.24
10 50 4.00 6.92 7.07 9.33 10.18
15 59 4.00 6.90 7.05 9.27 10.12
20 68 4.00 6.88 7.03 9.22 10.06
25 77 4.01 6.86 7.01 9.18 10.01
30 86 4.02 6.85 7.00 9.14 9.96
35 95 4.03 6.84 6.99 9.11 9.92
40 104 4.04 6.84 6.98 9.07 9.88
45 113 4.05 6.83 6.98 9.04 9.85
50 122 4.06 6.83 6.98 9.01 9.82
55 131 4.08 6.84 6.98 8.99 9.79
60 140 4.09 6.84 6.98 8.97 9.77
65 149 4.11 6.84 6.99 8.95 9.76
70 158 4.12 6.85 6.99 8.93 9.75