Hanna Instruments Foodcare HI9350011 User manual

HI9350011
Portable K-Type Fast Response Thermometer for
Foodcare Products
SPECIFICATIONS
•RANGE* -50.0 to 199.9 ºC ; 200 to 300 ºC
-58.0 to 399.9 ºF ; 400 to 572 ºF
•METER ACCURACY ±0.4 ºC (-50.0 to 300 ºC)
@ 23.0 °C ±5 °C ±0.7 ºF (-58.0 to 572 ºF)
•PROBE ACCURACY ±1.6 ºC (-50.0 to 300 ºC)
FC766C1 ±2.9 ºF (-58.0 to 572 ºF)
*The measurement range may be limited by probe type, and applies to the probe shaft.
OPERATIONAL GUIDE
•To switch ON and OFF: press ON/OFF ( ).
•To take measurements: connect a suitable temperature probe to the meter.
At start-up the thermometer displays all LCD segments for a few seconds,
followed by the percentage indication of the remaining battery life. It then
enters CAL Check mode followed by measurement mode.
If a temperature probe is plugged in, the meter displays the measured
temperature.
If reading is slightly beyond the measurement range, the meter flashes the
closest full-scale value.
To switch the meter OFF, press the ON/OFF key.
•For auto-off feature:
To save battery life, each model is provided with an auto-off feature, which
switches the instrument off after a certain period of non use.
The auto-off feature can be set in 3 modes from SETUP MENU: 8 minutes,
60 minutes or disabled.
• Calibration Check mode:
The meter is provided with an automatic CAL Check feature at start-up, which
allows the user to check the instrument calibration status. If the meter is
calibrated, the display will stabilize and show “0.0 °C” (±0.3 °C) for a
few seconds.
Warning messages:
• “NO PROBE“message: when the probe is not connected or the signal is
interrupted.
• “Err“message: if during Calibration Check the meter displays more than
±0.3 °C. Contact your local Hanna Instruments Office for recalibration.
• DAMAGED PROBE message: when the readings are very far from the
measurement range, the probe may be damaged. The display shows
blinking dashes and “NO PROBE” message is displayed.
Quick Reference Guide

METER SETUP
•To enter Setup MODE: press SET button located inside the battery
compartment.
•To switch between “°C“ or “°F“: press ON/OFF ( ).
Long press ON/OFF button once to save and continue to auto-off settings.
•To cycle through the Auto-Off choices: press ON/OFF ( ).
Long press ON/OFF button once to save and continue to normal operation.
BATTERY REPLACEMENT
If the display shows battery level “0%” it means the battery charge is not enough
to guarantee good measurements and the Battery Error Prevention System (BEPS)
turns the meter off. Immediately replace the batteries with new ones.
Battery replacement must only take place in a non-hazardous area.
The batteries are accessed by opening the battery cover on the back of the
instrument.
Replace the three 1.5V AAA alkaline batteries located in the battery compartment,
observing the polarity on the rear of the instrument.
Replace the battery cover making sure that the gasket is in place.
INTENDED USE
The thermometers are waterproof and are rated IP65.
The meters are specifically designed for measuring the temperature
in all areas of the food sector.
Both air temperature and product internal temperature can be measured with
these thermometers.
The probe shaft is designed for continuous contact with foodstuffs in accordance
with Regulation (EC) 1935/2004.
Refer to the probe section of this manual for more information on the available
probes.
TEMPERATURE PROBES
The temperature probes are pre-calibrated at the factory and ready-to-use. These
interchangeable probes make it possible to switch from one probe to another
within the family without requiring recalibration.
Note: To clean the meter and the probe, do not use aggressive
detergents. It is recommended to use water.
QR9350011 04/18
SET button