Hanna Instruments HI 149-00 User manual

Instruction Manual
HI 149-00
HI 149-01
Remote Probe
Thermometer
EN 50081-1
EN 50082-1
Stay in Touch with the Manufacturer!
Foodcare
Visit our Internet Home Page:
http://www.hannacan.com
ACCESSORIES:
Probe EPW: penetration/general purpose probe
Probe ELW: liquid/general purpose probe
Probe ECW: air/gas probe
Probe EMW: surface probe
90mm
3.5" 195mm
7.7"
90mm
3.5" 235mm
9.3"
90mm
3.5" 240mm
9.4"
90mm
3.5" 270mm
10.6"
Before using this product, make sure that it is entirely suitable for the environment in which
it is used. Operation of this instrument in residential area could cause unacceptable
interferences to radio and TV equipments, requiring the operator to take all necessary
steps to correct interferences. Any variation introduced by the user to the supplied equipment
may degrade the instrument's EMC performance. To avoid electrical shock, do not use this
instrument when voltages at the measurement surface exceed 24VAC or 60VDC. To avoid
damages or burns, do not perform any measurement in microwave ovens.
SUGGESTIONS FOR USERS:

HI 149 is a portable K-Type thermocouple ther-
mometer for routine use in food industry appli-
cations.
With four probes to choose from, HI 149 can be
used in most applications including air & gases,
liquids, surfaces and semi-solids. Each probe
has a stainless steel shaft that resists the
harmful effects of chemicals.
HI 149 is available in Celsius (HI 149-00) and
Fahrenheit (HI 149-01).
BACK
POCKET
CLIP
TEMPERATURE
PROBE
HOLDERS
TEMPERATURE
PROBE
CABLE
REAR
COVER
FRONT
COVER
FRONT
LIQUID
CRYSTAL
DISPLAY
°c
020
Foodcare
• Connect one of the four
probes (see accessories) by
opening the rear cover and
by inserting the 3-pin probe
connector into place
• To switch the HI 149 on, slide
off the front cover and push
the ON/OFF switch upwards
to the “ON” position.
• The temperature will be dis-
played in either °C or °F de-
pending on the model used.
OPERATION:
REAR
COVER
REAR
COVER
PULL
FROM
TOP
3-PIN
PROBE
CONNECTOR
SLIDE
DOWN
°c
ON
OFF
°c
Foodcare
020
Foodcare
• To exchange the probe, open the rear cover of the
unit and release the probe connector prior to insert-
ing the new probe.
• When not in use, switch the HI 149 off.
• Variations in readings or fading display can indicate
weak batteries.
When the HI 149 cannot
be switched on or the dis-
play fades, pull out the
rear cover, remove the
battery cover and replace
all the three 1.5V batter-
ies, paying attention to their polarity.
Batteries should only be replaced in a safe area
using the battery type specified in this instruc-
tion sheet.
BATTERY REPLACEMENT:
REAR
COVER
PULL
FROM
TOP
BATTERIES
BATTERY
HOUSING
BATTERY
COVER
REAR
COVER
SPECIFICATIONS:
HI 149-00(°C) HI 149-01(°F)
Range -40 to 300°C -40 to 572°F
Resolution 1°C 1°F
Accuracy ±2°C ±4°F
Typical EMC ±2°C ±4°F
Deviation
Probe stainless steel probe (interchangeable)
with 1m cable
Battery Type 3 x 1.5V
Battery Life Approx. 700 hours
of continuous use
Dimensions 106x68x21mm (4.2x2.7x0.8”)
Weight 80g (2.8 oz.)