Hanover TRAD5PCCFP-RED User manual


HanoverOutdoorFurniture




IMPORTANT
Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),
PLEASEDONOTRETURNTOTHERETAILER/STORE
fromwhereyoupurchasedtheproduct.
PleasecallourToll‐FreeCustomerServiceHotlineat:1‐800‐416‐3511
Between9:00AMand5:00PMEasternTime,MondaythroughFriday
Orvisitourwebsiteat:www.hanover‐products.com


Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty
Cardandreceiptforfutureuse.
For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor
furniture,pleasevisitourwebsiteat:www.hanover‐products.com.
6/1/2015(a)

Page 4
*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE
PARTS IDENTIFICATION LIST
AAF06000
PARTS LIST ORDER PART #DESCRIPTION
AFOOT CAP
FACTORY ASSEMBLY
FC0030
A

ASSEMBLY INSTRUCTIONS
WARNING
Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
An LP-cylinder not connected for use
shall not be stored in the vicinity of this
or any other appliance.
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. If odor continues, keep away from
the appliance and immediately call
your gas supplier or fire department.
WARNING:
USE FACTORY APPROVED
REPLACEMENT PARTS AND
ACCESSORIES ONLY. USE
OF UNAPPROVED PART OR
ACCESSORIES CAN VOID
THE WARRANTY ON THIS
PRODUCTAND RESULT IN
AHAZARDOUS CONDITION.
PLEASE CONTACT US FOR
INFORMATION REGARDING
REPLACEMNT
HOSES,THERMOCOUPLES,
ELECTRODES,IGNITION
MODULES,LAVAROCKS,LO
GS, FIRE ICE, ETC.
WARNING:
Improper installation, adjustment alteration,
service or maintenance can cause injury or
property damage. Read the installation,
operating and maintenance instructions
thoroughly before installing or servicing this
equipment.
FOR USE WITH 20LB (9KG) PROPANE
CYLINDER WITH TYPE 1 CONNECTION OR FOR
USE WITH NATURAL GAS AFTER CONVERSION
KIT IS INSTALLED (MUST BE PROFESSIONALLY
INSTALLED) ALSO THE LP REGULATOR MUST
BE SUPPLIED BY THE MANUFACTURER.
Dec 2014
Installer: Leave these instructions with consumer.
Consumer: Keep these instructions for future reference.
WARNING: For Outdoor Use Only
Questions, Problems, Missing Parts? Before returning to
your retailer, call our customer service department in the
US and Canada at 1-800-416-3511, Monday-Friday, 9 a.m.–
5 p.m.Eastern Time.
This appliance can produce carbon
monoxide which has no odor.
Using it in an enclosed space can kill
you.
Never use this appliance in an enclosed
space such as a camper, tent, car or
home.
DANGER CARBON MONOXIDE HAZARD
CSA Model 99000 ARL00100

PARTS IDENTIFICATION LIST
PART DESCRIPTION PART# QTY
A CONTROL KNOB FP1245 1
B GAS VALVE FP0307 1
C THERMOCOUPLE FP0004 1
D LP REGULATOR
HOSE 65-FP-0181 1
E ELECTRODE 65-FP-0128 1
F ORIFICE ELBOW FP0310 1
G IGNITION MODULE FP0006 1
H PROPANE
ORIFICE ZCF0021 1
I “AAA”
BATTERY(1.5V) HW0705 1
J LAVA ROCK SET FP0002 1
K FOOTCAP FC0559 4
L 1/4" X 15 MM BOLT HW0034 8
M 1/4" X 20 MM BOLT HW0036 4
N 1/4" X 40 MM BOLT HW0086 4
O BOLT COVER HW0105 18
P Ø6.5 X 1.0 MM
WASHER HW0004 14
Q Ø18XØ6.5 X1.5MM
WASHER HW0103 4
R NUTS HW0717 2
S HEX BOLT DRIVER HW0006 1
T HEX WRENCH HW0008 1

U FIREPIT TABLE
TOP 1
V BACK PANEL 1
W
LEFT SIDE
PANEL 1
X
RIGHT SIDE
PANEL 1
Y
DOOR PANEL 1
Z MIDDLE SUPPORT 1
AA
LP SUPPORT 1
BB BOTTOM/ TOP
CONNECTOR 1

INSTALLATION
1.Identify parts packed in carton against the parts list. Remove all protective materials and
set parts on a flat, non-abrasive surface.
2. Attach the back panel to the side panels by using four 1/4"x40 mm bolts and washers
as shown in Figure 2.Guide the bolts through the holes in back panel, into the pre-drilled
holes in the side panels. Hand tighten only.
Figure 2
3. Attach the middle support to the side panels by using four 1/4"x15 mm bolts and
washers as shown in Figure 3.Guide the bolts through the holes in the middle support, into
the pre-drilled holes in the side panels. Hand tighten only.
Figure 3
4. Attach the "L" connector to right side panel by using a 1/4"x15 mm bolt and washer as
shown in Figure 4.Guide the bolt through the hole in the "L" connector, into the pre-drilled
hole in the right side panel. Do not over tighten.
Figure 4

5. Put the door onto the bottom connector, guide the pin in the bottom connector into the
hole on the underside of the door. Then guide the pin on the top connector into the hole in
the topside of the door, use a 1/4"x15 mm bolt and washer to attach this top connector to
the right side panel as shown in Figure 5. Do not over tighten.
Figure 5
6. With the help of another person, carefully place the table top onto the table base. After
making any necessary adjustments to the alignment of the table top and the assembled
base, use four 1/4"x20 mm bolts and washers as shown in Figure 6.Guide the bolts
through the holes in the base, into the pre drilled holes in the table top. Do not tighten
completely.
Figure 6

7. Attach the LP support the to door panel by using four 1/4"x15 mm bolts and washers as
shown in Figure 7. Do not over tighten.
Figure 7
8. Place gas tank onto the LP support as shown in Figure 8.
9. Attach the metal ring ( as shown in Figure 9) pre-fitted with gas hose which is
connected to the table top , into the hole of the door panel, then use hex bolt driver to
screw 1/4"x5mm nut , the gas tank has fixed as shown in Figure 9a. Connect the regulator
as shown in Figure.10 Screw the black handle clock-wise to tighten. Turn the handle
counter clock-wise to remove. The hose must point down. Check that the valve is turned
all the way clockwise to the "OFF" position.
Figure 8

Figure9
Figure10
10. After making any necessary adjustments to the parts, use the hex bolt driver to tighten
all bolts.
Note: each bolt must be tightened a few revolutions at a time.
Repeat until all bolts are tight. Do not over tighten. Over tightening may strip bolts. Cover
all bolts with covers.
12. Pour the lava rocks into the burner pan completely covering the burner. See Figure 11.
Ignition Well
Figure 11
Figure 9a

13. Remove the cardboard cover from the ignition well as shown in Figure 12. Remove
any lava rock or fire ice on top of ignition well.
Cardboard Cover
14. Open the tank valve. Apply a solution of soapy water to the tank-regulator connection
and to the valve-hose connection to check for leaks as shown in Figure 13. If soap
bubbles continue to form, the connection has a leak. If a leak is found, close the tank valve
and tighten all connections.
NOTE: NEVER USE A FLAME TO CHECK FOR LEAKS.
BATTERIES
Make sure the control knob is in the "OFF" position.
Unscrew the push button cap on the ignition module located
on the control panel to access the battery compartment. The
ignition module requires one Alkaline AAA size battery
(1.5V). The negative (-) end goes in first. See Figure 14.
Dispose of battery safely. May explode or leak if charged or
disposed of in fire. Make sure of the polarity. Mercury and
cadmium free.
Figure 14
Figure 12
Checking the tank-regulator for leaks
Figure 13