Hanover Orleans ORL4PCTFPSW2-TAN User manual


HanoverOutdoorFurniture




IMPORTANT
Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),
PLEASEDONOTRETURNTOTHERETAILER/STORE
fromwhereyoupurchasedtheproduct.
PleasecallourToll‐FreeCustomerServiceHotlineat:1‐800‐416‐3511
Between9:00AMand5:00PMEasternTime,MondaythroughFriday
Orvisitourwebsiteat:www.hanover‐products.com


Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty
Cardandreceiptforfutureuse.
For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor
furniture,pleasevisitourwebsiteat:www.hanover‐products.com.
6/1/2015(a)

Page 4
ASSEMBLY INSTRUCTIONS
1
2
Attach the seat frame to the back frame by using four 5/16"x40 mm bolts and washer as shown in
Guide these bolts through the holes in the seat frame, into the fixed nuts already in place in the back frame.
Figure 1.
.Do not over tighten
Attach love seat arm by inserting two mm bolts with washers through the holes in front seat portion
of the love seat frame and into the holes in the love seat arm shown in . Attach back of love seat arm
by inserting two mm bolts with washers through holes in the back portion of love seat frame and into
the holes in the rear portion of the love seat arm as shown in . . Repeat for the
opposite side.
Figure 2
Figure 2 Hand tighten only
5/16"x25
5/16"x40
A
B
H
F
G
C
D
G
EH
GFOOT CAP-1
FH
G
EH
G
FH
3Tighten all bolts using the hex bolt driver provided. Tighten each bolt a few revolutions at a time, alternating
between bolt connections until all bolts are tight.
Cover all bolts with bolt covers provided.
Do not over tighten. Over tightening may strip bolts or
damage the welds or frame.

Page 5
*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE
PARTS IDENTIFICATION LIST
BGC08006
8
5/16" X 40 MM BOLT
Ø8.5 X 1.5 MM
WASHER
LEFT ARM
RIGHT ARM
BOLT COVER
HEX BOLT DRIVER
FOOT CAP-1
FACTORY ASSEMBLY
HW0005
HW0022
HW0006
FC0030
1
12
HW0275
12
4
5/16" X 25 MM BOLT HW0186
1
1
1
1
BACK FRAME
SEAT FRAME
PARTS LIST DESCRIPTION ORDER PART # QTY
A
B
C
D
E
F
G
H
I
FOOT CAP-2
FACTORY ASSEMBLY FC0308
SK0939
SK0940
SK0941
SK0942

Page 4
ASSEMBLY INSTRUCTIONS
1
2
3
Assemble furniture on a smooth, non-abrasive surface. by using two
5/16"x40 mm bolts and washers as shown in . Guide the bolts through holes in back frame, into
pre-drilled holes in the . and back frame
by using four 5/16"x25 mm bolts and washers as shown in . A
and seat frame by using two 5/16"x25 mm bolts and two 5/16"x40 mm bolts and four washers as
shown in .
Fig.1
Hand tighten only.
Fig.2 Hand tighten only.
Fig.3 Hand tighten only.
Attach the back frame to right arm
right arm Attach the seat frame to right arm
ttach the left arm
to back
B
D
I
G
H
Fig.1
I
G
H
A
Fig.2
I
F
H
I
F
H
C
Fig.3
I
F
H
I
G
H
Attach the complete base to the complete seat by using four 5/16"x40 mm bolts and washers as shown
in . Guide the bolts through holes in base, into the pre-drilled holes in the seat.Fig.4 Hand tighten only.
Using the hex bolt driver provided, tighten all bolts.
Test the operation of glider. Gliding
motion should be smooth. Adjust tension on the glider brackets, nuts and bolts as needed. Cover nuts
and bolts with covers provided.
Do not over tighten bolts. If nuts and bolts are
too tight or too loose, the glider will not function properly.
I
G
H
Fig.4
E
I
G
H

Page 5
*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE
PARTS IDENTIFICATION LIST
G0080
PARTS LIST
HW0695
HEX BOLT DRIVER HW0006
SEAT FRAME
1
1
1
A
B
C
D
E
F
G
H
I
J
DESCRIPTION ORDER PART # QTY
GLIDER BRACKET
FACTORY ASSEMBLY
ST4 8 X 25 BOLT.
FACTORY ASSEMBLY
FOOT CAP
FACTORY ASSEMBLY FC0013
6
5/16" X 25 MM BOLT HW0186
8
5/16" X 40 MM BOLT HW0275
HW0005Ø8.5 X 1.5 MM WASHER
BOLT COVER HW0105 14
BACK FRAME 1
LEFT ARM 1
RIGHT ARM 1
GLIDER BASE W/
GLIDER BRACKET 1
14
SG0154
SG0155
SG0156
SG0157
SG0158
SG0159
BGS12023

ASSEMBLY INSTRUCTIONS
WARNING
Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
An LP-cylinder not connected for use
shall not be stored in the vicinity of this
or any other appliance.
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. If odor continues, keep away from
the appliance and immediately call
your gas supplier or fire department.
WARNING:
USE FACTORYAPPROVED
REPLACEMENT PARTS AND
ACCESSORIES ONLY. USE
OF UNAPPROVED PART OR
ACCESSORIES CAN VOID
THE WARRANTY ON THIS
PRODUCTAND RESULT IN
AHAZARDOUS CONDITION.
PLEASE CONTACT US FOR
INFORMATION REGARDING
REPLACEMNT
HOSES,THERMOCOUPLES,
ELECTRODES,IGNITION
MODULES,LAVAROCKS,LO
GS, FIRE ICE, ETC.
WARNING:
Improper installation, adjustment alteration,
service or maintenance can cause injury or
property damage. Read the installation,
operating and maintenance instructions
thoroughly before installing or servicing this
equipment.
FOR USE WITH 20LB (9KG) PROPANE
CYLINDER WITH TYPE 1 CONNECTION OR FOR
USE WITH NATURAL GAS AFTER CONVERSION
KIT IS INSTALLED (MUST BE PROFESSIONALLY
INSTALLED) ALSO THE LP REGULATOR MUST
BE SUPPLIED BY THE MANUFACTURER.
Jan-01-2015
Installer: Leave these instructions with consumer.
Consumer: Keep these instructions for future reference.
WARNING: For Outdoor Use Only
Questions, Problems, Missing Parts? Before returning to
your retailer, call our customer service department in the
US and Canada at 1-800-416-3511, Monday-Friday, 9 a.m.–
5 p.m.Eastern Time.
This appliance can produce carbon
monoxide which has no odor.
Using it in an enclosed space can kill
you.
Never use this appliance in an enclosed
space such as a camper, tent, car or
home.
DANGER CARBON MONOXIDE HAZARD
CSA Model99010 ARL00200

PARTS IDENTIFICATION LIST
PART DESCRIPTION PART# QTY
A CONTROL KNOB FP1245 1
B GAS VALVE FP0307 1
C THERMOCOUPLE FP0004 1
D LP REGULATOR
HOSE 65-FP-0181 1
E ELECTRODE 65-FP-0128 1
F ORIFICE ELBOW FP0310 1
G IGNITION
MODULE FP0006 1
H PROPANE
ORIFICE ZCF0021 1
I “AAA”
BATTERY(1.5V) HW0705 1
J LAVA ROCK SET FP0002 1
K FOOTCAP FC0743 4
L 1/4" X 15 MM BOLT HW0034 8
M 1/4" X 20 MM BOLT HW0036 4
O 1/4" X 40 MM BOLT HW0086 4
P HEX BOLT DRIVER HW0006 1
Q BOLT COVER HW0105 18
R WASHERS-1 HW0004 14
S WASHERS-2 HW0712 4
T NUTS HW0717 2
U HEX BOLT
DRIVER HW0008 1

V TABLE RIM 1
W BACK PANEL 1
X LEFT SIDE PANEL 1
Y
RIGHT SIDE
PANEL 1
Z DOOR PANEL 1
AA LP SUPPORT 1
BB TILE-1 4
CC TILE-2 4
DD MIDDLE SUPPORT 1
EE TABLE COVER 1
FF BOTTOM/ TOP
CONNECTOR 1

INSTALLATION
1. Identify parts packed in carton against the parts list. Remove all protective materials and
set parts on a flat, non-abrasive surface.
2. Attach the back panel to side panels by using four 1/4"x40 mm bolts and washers as
shown in Figure 2. Guide bolts through holes in back panel, into pre-drilled holes in the
side panels. Hand tighten only.
Figure 2
3. Attach the middle support to the side panels by using two 1/4"x15 mm bolts and
washers as shown in Figure 3. Guide bolts through the holes in the middle support, into
pre-drilled holes in the side panels. Hand tighten only.
Figure 3
4. Attach the "L" connector to right side panel by using a 1/4"x15 mm bolt and washer as
shown in Figure 4. Guide bolt through hole in "L" connector, into pre-drilled hole in the
right side panel. Do not over tighten.
Figure 4

5. Put the door onto the "L" connector (pre-assembled), guide the pin on the lower "L"
connector into the hole under the door. Then guide the pin on the upper "L" connector
into the hole in the upper portion of the door. Use a 1/4"x15 mm bolt and washer to
secure the "L" connector to the right side panel as shown in Figure 5. Do not over
tighten.
Figure 5
6. With the help of another person, carefully place the table top onto the table base.
After making any necessary adjustments to the alignment of the table top and the
assembled base, use four 1/4"x15 mm bolts and washers as shown in Figure 6. Guide
the bolts through the holes under the table top, into the pre-drilled holes in the side
panels. Do not tighten completely.
Figure 6
7. Attach the LP support to door panel by using four 1/4"x15 mm bolts and washers as
shown in Figure 7. Do not over tighten.
Figure 7

8. Place gas tank onto the LP support as shown in Figure 8.
Figure 8
9. Attach the metal ring (as shown in Figure 9) pre-fitted with gas hose which is
connected to the table top, into the hole of the door panel, then use hex bolt driver to
screw 1/4"x5mm nut, the gas tank has fixed as shown in Figure 10. Connect the
regulator as shown in Figure10. Screw the black handle clock-wise to tighten. Turn the
handle counterclockwise to remove. The hose must point down. Check that the valve is
turned all the way clockwise to the "OFF" position.
Figure 10
Figure 9

10. After making any necessary adjustments to the parts, use the hex bolt driver to tighten
all bolts. Note: each bolt must be tightened a few revolutions at a time. Repeat until all
bolts are tight. Do not over tighten. Over tightening may strip bolts. Cover all bolts with
covers.
11. Note the clear bumpers spaced evenly throughout the inside of the table top. Carefully
place tiles inside table rim, resting on the clear bumpers as shown in Figure 11
Figure 11
12. Pour the lava rocks into the burner completely covering the burner. See Figure 12
Ignition Well
13. Remove the cardboard cover from the ignition well as shown in Figure 13. Remove
any lava rock or fire ice on top of ignition well.
Cardboard Cover
Figure 12
Figure 13

14. Open the tank valve. Apply a solution of soapy water to the tank-regulator connection
and to the valve-hose connection to check for leaks as shown in Figure 14 If soap
bubbles continue to form, the connection has a leak. If a leak is found, close the tank
valve and tighten all connections.
NOTE: NEVER USE A FLAME TO CHECK FOR LEAKS.
BATTERIES
Make sure the control knob is in the "OFF" position.
Unscrew the push button cap on the ignition module
located on the control panel to access the battery
compartment. The ignition module requires one Alkaline
AAA size battery (1.5V). The negative (-) end goes in first.
See Figure 15 Dispose of battery safely. May explode or
leak if charged or disposed of in fire. Make sure of the
polarity. Mercury and cadmium free.
Checking the tank-regulator for leaks
Figure 14
Figure 15

LIGHTING INSTRUCTIONS
Warning: If these instructions are not followed exactly, a fire or explosion may result in
causing property damage, personal injury or loss of life.
1. Make sure the control knob is in the "OFF" position. See Figure 16 Open the tank valve
all the way.
2.Push in the igniter button. You will hear a slight clicking sound. With the igniter button
pushed in, push and turn the control knob to the “ON” position. The fire should light within
a few seconds. Once the flame is lit, release the igniter button and continue to hold the
control knob in for 10 to 15 seconds. Release the control knob. The control knob should
pop back out and then remain lit.
Note: If the fire does not light, turn the knob to the “OFF” position and wait five (5) minutes
before trying again.
3. To turn down the flame, push the control knob in slightly and turn to Medium (medium
or Low (small flame).
4. To shut down the fire pit, turn the control knob to the “OFF” position and turn off the tank
valve.
MAINTENANCE
The flames should look like those in Figure 17 To clean the burner,
use a soft brush after the burner has cooled completely. Never
use a vacuum cleaner on the burner. It is recommended that the
fire pit be stored indoors during the winter if it will be subjected to
freezing temperatures. The LP cylinder must be disconnected and
removed from the appliance before the appliance can be stored
indoors.
Figure 17
IGNITER BUTTON CONTROL KNOB
Figure 16

TROUBLESHOOTING GUIDE
PROBLEM CAUSE REMEDY
No Propane Gas at Burner
Check that gas tank valve is
open. Turn control knob to “ON”
and push control knob in. Make
sure tank has propane gas.
No Spark at Electrode
Check that AAA battery is
installed with negative (-) end
first and has a charge. Check
that the wire is connected to the
ignition module. Check that the
electrode is not cracked or
broken.
Burner won’t light
Lack of oxygen Remove excess lava rocks or
fire ices from around the ignition
well.
Thermocouple not in flame
Check that the tip of the
thermocouple is even with the
top of the ignition well. Remove
any lava rocks from the igntion
well.
Thermocouple connection
at the main control valve is
loose
Tighten the thermocouple nut at
the back of the valve.
Burner won’t stay
lit after lighting
No Lava Rocks on Burner Cover the burner with lava rocks
per the instructions