Hans Grohe Metris 31436 1 Series Installation guide

Metris
31436XX1
Metris
31446XX1
Focus
31732XX1
Focus
31733XX1
Talis
32313XX1
Talis
32314XX1
Installation Instructions / Warranty

2
Trim, 3- and 4-Hole Roman Tub Sets
3-Hole 4-Hole
Metris 31436001 31446001
Focus 31732001 31733001
Talis 32313XX1 32314XX1
Installation Considerations
The 4-Hole Roman Tub Set trim kits require rough 06646000. The 3-Hole trim kits require rough
06607000. The rough valves are not included.
The rough must be installed and the mounting surface complete and made watertight before instal-
lation of this trim kit.
The elbow for the handshower incorporates a check valve to prevent back siphonage. This check
valve should be removed and inspected yearly.
The flow rate of the handshower is 2.5 gpm.
The water must be shut off at the main before beginning installation.
31436XX1 31446XX1

3
31732XX1 31733XX1
32313XX1 32314XX1

4
Installation - 3-Hole Trim Kits
If you are using a 4-Hole set, please turn to page 6
Install the Handles
Remove the plaster shields from the hot and cold valves
and the spout tee.
Assemble the Spout
Remove the brass plug from the tee.
Install the handle escutcheons.
Install the white plastic snap connectors and the screws.
Push the handle down firmly over the snap connectors.

5
Push the spout sealing ring firmly into the spout tee.
Install the spout escutcheon.
Press the spout over the spout tee. Install and tighten the
set screw with a 3 mm Allen wrench.
CAUTION: do not overtighten the set screw or the o-rings
on the diverter will deform, which will cause a leak.
Turn on the water and check all connections for leaks.

6
Installation - 4-Hole Trim Kits
Install the Handles
Remove the plaster shields from the hot and cold valves
and the spout tee.
Assemble the Diverter and Spout
Remove the brass plug from the tee.
Install the escutcheons.
Install the white plastic snap connectors and screws.
Push the handle down firmly over the snap connector.

7
Install the spout escutcheon.
Firmly press the spout over the tee and diverter. Tighten
the set screw with the included 3 mm Allen wrench.
CAUTION: do not overtighten the set screw or the o-rings
on the diverter will deform, which will cause a leak.
Install the pull rod. The threaded end of the pull rod must
go into the hole in the pin.
Press the diverter assembly firmly into the spout tee until
it is fully seated. Turn the guide bushing so that the slot
faces the rear of the spout.

8
Install the Handshower Holder Escutcheon and
Handshower (4-Hole version only)
Install the check valve in the elbow, with the arrow
pointing in the direction of the water flow.
Remove the plaster shield from the handshower holder.
Pull out on the handshower hose.
Screw the handshower holder escutcheon into place.
Install the elbow.
Place the screen washer in the elbow. Screw the
handshower into the elbow.
Guide the handshower into the holder.

9
Scale Removal
The Raindance Air 1-jet handshower incorporates the
RubitTM cleaning system. If scale deposits are noticed in
the spray channels, turn the water on lightly and rub the
spray channels with a finger or a sponge.
If scale deposits are noticed on the spray face, pour
about 3/4” of a commercial scale remover, such as Lime-
AwayTM or CLRTM ,into a shallow dish. Dilute the remover
according to the label instructions.
Soak only the spray face in the solution for the amount of
time specified on the label.
Rinse the handshower with clear water.
Reinstall the handshower. Turn on the water and allow
the handshower to flush for at least one minute.

10
Replacement Parts 3-Hole Roman Tub Sets
Metris
Focus
Talis
1
2
3
4
2
3
4
2
3
4
1
11
12
13
14 14
14
17
17
17