Happy Beds Solo Metal Bed 3ft User manual

Solo Metal Bed 3ft
Assembly Instructions
www.happybeds.co.uk
Important before assembly:
Read these instructions carefully before assembling or using the product.
Please check the contents of the boxes before attempting to assemble this product. The instructions will
have a checklist of parts and fittings.
It would be sensible to lay a rug or a carpet on the floor where you intend to assemble the product,
to void scratches and damaging the product or the floor.
Assemble the product as close to its intended final location/room as possible.
Do NOT use any power tools as this may damage the frame.
Health & Safety:
This product or some parts of this product will be heavy. Please use an assistant when lifting.
DO NOT jump on the product or any of its parts.
DO NOT use this product if any parts are missing, damaged or worn.
DO NOT use this product unless all fixings are secured.
Please keep small parts out of reach of children.
Always use on a level, even surface.
Please keep these instructions for future reference.

@
This product or some parts of this product will be heavy. Please use an assistant
when lifting.
Never drag or push the pieces across a hard or stone floor as this will cause
damage to the joints. Use a carpet or a rug for extra care.
If you have problems assembling or have damaged or missing pieces, please
contact us by visiting:
https://www.happybeds.co.uk/customer-service
(Not metal)
These tools are not
necessary, but may
help to assemble
certain parts of the
product.
Do NOT use any power
tools as this may
damage the frame.

1
Vendor: S000053
Part List
Part
1A 14
2
B
1
8
3
C
2
4
4
D
2
4
5
6
7E
1
1
324
Description
Headend
Footend
Side Support (with sticker)
Side Support
Base Leg
Mid Support
Slat
DescriptionBox Qty
Hardware List (found in box 1)
Part
**M4 Allen Key provided
Step 1: Fix the Side Supports (3) and (4) to the headend (1) and footend (2) using hardware part (B) but do not fully tighten yet.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 2: Place the base leg (5) in the middle of the side supports (3) and (4).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Page 2 of 3
Qty
Small Allen Key
1
3B
B
2
5
7
34 6
B203 : 50mm
Black Round Stopper
M6 x 16mm
JCBC Screw
M6 x 40mm
JCBC Screw
Single Slat Cap
M6 Nut
1
1
2
2
2
1
12
4
3
5

Vendor: S000053
Step 3 : Place the mid support (6) at the center and screw together with the base leg (5) using hardware parts (C) and (D).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 4 : Insert hardware part (A) to the bed legs.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 5 : Place hardware part (E) onto every end of each slat (7) then press rmly into the side supports (3) and (4).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Page 3 of 3
C
C
D
D
3
4
Allen Key
6
5
3
1
7
E
7
A
A
2

www.happybeds.co.uk
General Care & Maintenance
Please dispose of all packaging safely.
Wipe clean with a slightly damp cloth.
Avoid the use of all household cleaners and abrasives.
Periodically check all screw & fixings to ensure they are secure.
When moving your product, carefully lift into place. Never drag or push the pieces across the
floor as this will cause damage to the joints and could result in failure to the product that will
invalidate the warranty.
For more information on cleaning and product care visit:
https://www.happybeds.co.uk/help-and-advice
We’ve tried to make this product as easy to assemble as possible. In the unlikely event that
you have problems putting it together or have damaged or missing pieces, please contact
us by visiting:
https://www.happybeds.co.uk/customer-service
Notes