Harbor Freight Tools 40089 User manual

OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright©2002by Harbor FreightTools®. Allrights reserved. No portion of thismanual
or any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions please call 1-800-444-3353
GRINDER/BUFFER
CABINET
40089
®

SKU 40089 PAGE 2
SAVETHIS MANUAL
You will need the manual for the safety warnings and precautions, assembly
instructions,operating and maintenance procedures,parts list and diagram. Keep your invoice with
this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice
in a safe and dry place for future reference.
SAFETYWARNINGS AND PRECAUTIONS
1. KEEP PRODUCT USAGE AREA CLEAN. Clutteredareasinviteinjuries.
2. KEEP CHILDREN AWAY FROM PRODUCT USAGE AREA. Do not allow children to climb on this
product or play around tools or supplies.
3. DO NOT USETHIS PRODUCT IF UNDERTHE INFLUENCE OF ALCOHOL OR DRUGS. Read
warninglabels on prescriptions todetermine ifyourjudgementorreflexes are impaired whiletaking
drugs. If there is any doubt, do not attempt to use this product.
4. STAY ALERT. Watch what you are doing at all times. Use common sense. Do not use a Buffer or
Grindermounted on this productwhenyouaretired or distracted.
5. CHECK FOR DAMAGED PARTS. Before using this product, carefully check that it will operate properly
and perform its intended function. Check for damaged parts and any other conditions that may affect
itsoperation. Replaceorrepair damaged orworn partsimmediately.
6. DO NOT MODIFYTHIS PRODUCT.This product is designed to support a Grinder or Buffer.Do
not modify this Cabinet in an attempt to use it for other purposes.
7. REPLACEMENT PARTS AND ACCESSORIES. Whenservicing,useonlyidenticalreplacement
parts.Only use accessories intended for use with this product. Approved accessories are
availablefromHarborFreightTools.
8. USETHIS PRODUCT only for its intended use, as described in this manual.Do not use
attachments or modify it in any way.
9. BE SURE to use proper hardware(not included)to secure GrinderorBuffer.
NOTE: Always read and adhere to all warnings and instructions provided in the instruction manual of the buffer
orgrinderbeingused.
WARNING:The warnings, cautions and instructions discussed in this instruction manual cannot cover all
possible conditions and situations that may occur.It must be understood by the operator that common sense
and caution are factors which cannot be built into this product, but must be supplied by the operator.
SPECIFICATIONS
DESCRIPTION
Body: Formed and Stamped Sheet Steel
Black Powder Coat
34-1/4”H X 15-3/4”L X 12-3/8”W
3/8”W X 2-3/4”L (6X Slotted Holes)
308” Dia. (4X)
13-3.8” X 12-3/8”
12-1/8” X 12-3/8”
10-5/8” X 12-3/8”
12-7/8”W X 10”L X 1-7/8”H
47 Lbs.
ITEM
Body Construction
Finish
Overall Dimensions
Top Mounting Holes
Base Mounting Holes
Lower Shelf
Middle Shelf
Top Shelf
Top Dimensions
Overall Weight

SKU 40089 PAGE 3
UNPACKING
When unpacking, check to make sure all parts shown on the Parts List (page 4) are included. If any parts are
missing or broken, please call Harbor FreightTools at the number shown on the cover of this manual as soon
as possible.
ASSEMBLY INSTRUCTIONS
NOTE: All parts below refer to the parts listed on page 4 of this manual.
Assembly
3. Starting with the Base (#1), fit the side panels over the Base, lining up the holes. Use the Bolt (#9) through
the holes. Secure with Washer (#8) and Nut (#7). Repeat with Side Panels (#2A & #2B). Attach Back Panel
(#5) to Side Panels and Base in the same way.
4. Slide in Shelves (larger on bottom and graduating up to smallest) (C & D). Secure each shelf with Bolts (#9),
Washers (#8) and Nuts (#7) to Side Panels and Back Panel.
5. Attach Top (#6) aligning with remaining holes.With Bolt (#9) through the holes, secure with Washer (#8) and
Nut (#7) through front and back of Cabinet.
6. Choose where you want to place Cabinet permanently. Anchor through holes in Base (#1) with hardware for
cement or wood flooring, depending on where you choose to mount Cabinet so it is secure during Grinding
or Buffing for a strong sturdy work surface. (Hardware not included.)
7. Attach your Buffer or Grinder through the 6 top mounting holes (3/8” H X 2-3/4” L). Hardware will be
required (not supplied). A non flammable rubber pad (not supplied) for insulation, is recommended between
the Cabinet Top and the Buffer or Grinder. This pad will help reduce vibration.
1. To assemble Steel Grinding/Buffing Cabinet with three storage shelves you must first lay out all parts and
hardware on a clean surface.
2. Identify the Top Shelf (#6), the two Side Panels (#2A, #2B, right and left), the Base (#1), and the
Back Panel (#5).
#2B
#2A
#1
#5
#9, #8, #7
#C
#6
#D

SKU 40089 PAGE 4 REV 03/05
PART # DESCRIPTION QTY
1
2A
2B
C
D
5
6
7
8
9
Base
Left Side
Right Side
(larger) Shelf
(smaller) Shelf
Back Panel
Top (with sloted holes)
Nut (10MM)
Washer
Bolt (M6 X 1,00MM Round Flat)
1
1
1
1
1
1
1
16
16
16
PLEASE READ THE FOLLOWING CAREFULLY
THEMANUFACTURERAND/ORDISTRIBUTORHASPROVIDEDTHEPARTSDIAGRAMINTHISMANUAL
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY
REPRESENTATIONORWARRANTY OF ANY KINDTOTHE BUYERTHATHEORSHEISQUALIFIEDTO
MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY
PARTSOFTHEPRODUCT. INFACT,THEMANUFACTURERAND/ORDISTRIBUTOREXPRESSLYSTATES
THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSEDTECHNICIANS AND NOT BYTHE BUYER. THE BUYER ASSUMES ALL RISK AND LIABIL-
ITYARISINGOUTOFHISORHERREPAIRSTOTHE ORIGINAL PRODUCTORREPLACEMENTPARTS
THERETO,ORARISING OUT OF HISOR HER INSTALLATIONOFREPLACEMENT PARTSTHERETO.
MAINTENANCE
1. For better and safer performance, keep all parts of this product clean and dry at
all times.
(#2A)
(#6)
(#2B)
(#5)
(D)
(C)
(#1)
(#7)
(#8)
(#9)