Harbor Freight Tools 91460 User manual

FOLDABLE PORTABLE
TABLE
ASSEMBLY INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit ourWeb site at http://www.harborfreight.com
Copyright © 2004 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
91460

SKU 91460 Page 2
Specifications
Save This Manual
You will need the manual for the safety warnings and precautions, assembly instruc-
tions, operating and maintenance procedures, parts list and diagram. Keep your
invoice with this manual. Write the invoice number on the inside of the front cover.
Keep the manual and invoice in a safe and dry place for future reference.
SafetyWarnings and Precautions
1. Keep children away. Children must never be allowed in the work area during
setup. Do notletthemplay with oronthisTable. Donotallow childrenoradults
to stand/sit on the Table.
2. Store idle equipment. When not in use, this Table should be stored in a dry
location to inhibit rust.
3. Use the rightTable for the job. Do not exceed the weight capacity for any
piece. Do not attempt to force a smallTable to carry the weight of a larger one.
Therearecertain applicationsforwhichthisTablewas designed. Donotmodify
thisTable and do not use thisTable for a purpose for which it was not intended.
4. Use eye protection. Alwayswear ANSIapprovedimpactsafetygoggles during
setup.
5. Maintain with care. Keep thisTable clean for better and safer performance.
6. Stay alert. Watch what you are doing, use common sense.Do not setup this
Table if you are tired.
7. Check for damaged parts. Before using any Table, any part that appears
damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Check for any broken parts or mounting
fixtures;and any other condition that may affect proper operation.Any part that
is damaged should be properly repaired or replaced by a qualified technician.
8. Do not setup the Table if under the influence of alcohol or drugs. Read
warning labels if taking prescription medicine to determine if your judgment or
reflexes are impaired while taking drugs.If there is any doubt, do not setup the
Table.
DESCRIPTION
72-1/4”L X 29-3/4”W X 1-7/8”Thickness (Center Fold)
High Density Polyethylene Table Top-Tubular Steel Legs
350 Lbs. (Evenly distributed)
47 Lbs.
ITEM
Overall Dimensions
Materials
Weight Capacity
Unit Weight

SKU 91460 Page 3
9. Onlyuse thisTableon aflat,level,andsolid surfacecapable ofsupporting
weight of table and it’s contents.
Warning: The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur.It must
be understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
Unpacking
When unpacking, check to make sure the following parts are included.If any parts
are missing or broken, please call Harbor Freight Tools at the number on the cover
of this manual, or contact your local Harbor Freight retailer.
ASSEMBLY AND CAUTIONARY INSTRUCTIONS
1. Unlock the lock on the side of the Table. See Figure A. Place the unfolded
Table in an upside-down position on a smooth surface as in Figure B.
2. Remove the Pin (10) (in the bottom hole) of the Leg Hinge. Open the Leg
(3). Replace the Pin (10) in the upper hole as shown in Figures C.
Note: This Pin acts as a “safety”.Repeat directions on the second Leg.
See Figure D.
Figure A
Lock
Figure B Figure C
Remove
Pin (10)
from this
position
“Safety”
Position
of Pin (10)
Leg
Hinge
Figure D Figure E Figure F
Pin
(10)
Support
Pins (6)
“U”
Shaped
Handle
(8)

SKU 91460 Page 4
3. Place the two Support Pins (6) through the center portion of the Table frame
as shown in Figure E.
4. Set the Table upright by using the recessed “U” Shaped Handles (8) on the
sides of the Table. After standing Table up, push handles in.
See Figures F & G.
Figure G
5. To close the Table, reverse the instructions above. Be sure to lock the Table
so it can be stored away safely. Caution: Be careful not to pinch fingers.To
prevent back injury, use an assistant to set the Table upright.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHERTHE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSEDTECHNICIANS AND NOT BY THE BUYER.THE BUYER ASSUMES
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TOTHE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACE-
MENT PARTS THERETO.
NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts.

SKU 91460 Page 5
Parts List
Part # Description Qty.
Table
Table Frame
Leg
Rod Support
Link
Support Pin
Holder
U Shape Handle
Rivet 6 x 35
1
2
3
4
5
6
7
8
9
2
1
2
2
4
2
4
4
4
10
11
12
13
14
15
2
2
20
2
10
4
Part # Description Qty.
Pin
Rivet 6 x 16
Screw M5 * 16
Bolt M6 x 20
Nut M6
Rivet
Assembly Drawing
Part 1
Part 3
Part 12
Part 14
Part 10
Part 11
Part 6
Part 8
Part 2
Part 15
Part 7
Part 14 Part 12 Part 9
Part 11
Part 5