Harbor Freight Tools 90033 Quick reference guide

ASSEMBLY & OPERATING INSTRUCTIONS
HARLEY 30” (POLICE)
®
3
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web Site at www.harborfreight.com
TOY ROCKER
90033
90033 Police Harley .p65 10/30/03, 1:16 PM1

THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please complete the
owner’s record below:
Model______________ Serial No._____________ Purchase Date_______________
SAVE THE RECEIPT, WARRANTY AND THESE INSTRUCTIONS. It is important that you read the entire
manual to become familiar with the unit BEFORE you begin assembly.
Technical Specifications
Construction: Pine Wood
For ages: 3-8
Maximum Weight: 100 LBS.
Batteries: (3 qty.) 1.5V LR44 Button Cell
Safety Warnings and Precautions
WARNING: When using product, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use this product in damp or wet locations. Don’t
expose to rain. Keep work area well lighted.
3. Store idle equipment. When not in use, products must be stored in a dry location to inhibit
rust.
4. Check for damaged parts. Before using any product, any part that appears damaged should
be carefully checked to determine that it will operate properly and perform its intended function.
Check for any broken or damaged parts and any other conditions that may affect its operation.
Replace or repair damaged or worn parts immediately.
5. Replacement parts and accessories. When servicing, use only identical replacement parts.
Use of any other parts will void the warranty.
6. Use eye protection. Always wear ANSI approved impact safety goggles when assembling this
product.
7.Always check hardware and assembled parts after assembling. Use in an area that is
flat and level. All connections should be tight and hardware tightened.
8. All assembly should be done by an adult.
9. The Toy Rocker should be played with in the presence of an adult. The Toy Rocker is for
indoor use. Use on a padded surface, like a carpet.
10.This product contains small parts and therefore represents a choking hazard.
Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
#90033 Page 2
90033 Police Harley .p65 10/30/03, 1:16 PM2

Assembly
Your Toy Rocker will require complete assembly prior to use. It is important that you read the entire
manual to become familiar with the product BEFORE you use the Toy Rocker. Before assembling
the Toy Rocker be sure that you have all parts described in the Parts List and Assemby Diagram
located on the last pages of this manual.
Step 1) At each end of the Rocker Support (#2), insert the protruding dowel of the
Connecting Plate (#3) through the center hole in the Rocker Support (#2) and into
the Body (#1). The hole in Connecting Plate (#3) must line up with the holes in
Body (#1)-see Figure 1.
Figure 1-Body to Rocker Support
#90033 Page 3
Connecting Plate (#3)
Step 2) Secure the protruding dowel (on the Connecting Plate (#3) to the Body (#1)
by inserting two-sided Bolt (C) through Body (#1), extension of Connecting Plate (#3)
and out other side of Body (#1). On each end of Two-Sided Bolt (C), slide on Big
Washer (J), Spring Washer (L), and tighten on Nut (G)-see Figure 1.
Big Washer (J),
Spring Washer (L),
and Nut (G).
Big Washer (J),
Spring Washer (L),
and Nut (G).
(protruding dowel)
Step 3) Securing the Connecting Plate (#3) to the Rocker Support (#2). Insert the two (2)
Hex Bolts (B) down through the front Rocker Support (#2) and through each of the
outside holes in the Connecting Plate (#3)-see Figure 2. Slide on Small Spring
Washer (M), Medium Washer (K) and tighten on Nut (F).
Step 4) Connecting the Side Bags. The Side Bags have 4 side pieces (#6) and two front
pieces (#7). Connect the pieces as shown in Figure 2. Once in place, insert one
Hex Bolt (D) through each corner (4 corners on each side)-see Figure 2.
Hex Bolt (B)
Small Spring Washer (M),
Medium Washer (K)
and Nut (F).
Figure 2-Attaching Side Bags
Side View
Rocker Support (#2)
Side Bag
Hex Bolt (D)
Bolt (C)
Seat (#8)
90033 Police Harley .p65 10/30/03, 1:16 PM3

Step 5) Attach the rear Siren with Nut (H)-see Figure 3.
Figure 3
Step 6) To attach the Seat Bottom (#8), insert 2 Hex
Bolts (A) down through Seat Bottom (#8) - See
Figure 2.
Step 7) Insert Handlebar (#9) through top hole in forks.
Slide one Washer (I) onto each Screw (E) and
thread into hole in front of fork and into Handlebar
to secure in place-see Figure 4.
Siren
Handlebar (#9)
Screws (E) with
Washers (I)
Step 8) If decals are not attached, apply decals as shown on manual cover. Peel off decal
from paper and attach to Toy Rocker.
Siren Sound-Replacing Batteries
The Toy Rocker has a button on the console which makes a motor sound. The batteries are
replaceable as follows:
Step 1) Remove the Wooden Console cover by unscrewing the 2 Phillips Head Screws.
Remove cover from the plastic assembly-see Figure 5.
Step 2) Remove the 3 batteries and dispose of properly. Replace with new batteries.
Replace plastic assembly cover. Replace Console Cover and thread in 2 Phillips
Head Screws-see Figure 5.
#90033 Page 4
Figure 4
Wooden Console
Figure 5
90033 Police Harley .p65 10/30/03, 1:16 PM4

Unpacking
UNPACK AND CHECK CONTENTS
When unpacking your Harley 30” (Police) Toy Rocker, check to make sure the following parts are included. If
any parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353.
Part # Description Quantity Part # Description Quantity
1 Body 1 7 Side Bag-Front 2
2 Rocker Support 5 8 Seat 1
3 Connecting Plate 2 9 Handlebar 1
5 Rocker Slats 2
6 Side Bag-Sides 4
Part # Description Quantity Part # Description Quantity
A Hex Bolt 2 H Nut 1
B Hex Bolt 4 I Small Washer 2
C Bolt 2 J Big Washer 4
D Hex Bolt 8 K Medium Washer 4
E Screw 2 L Spring Washer 4
Hardware
F Nut 4 M Small Spring 4
G Nut 4 N Wrench 2
#90033 Page 5
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE
TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY
KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
O Allen Wrench 1
90033 Police Harley .p65 10/30/03, 1:16 PM5