Harbor Freight Tools U.S. GENERAL Junior 56515 Assembly instructions

Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
56515
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference. 23l
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright©2023 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

Page 2 For technical questions, please call 1-888-866-5797. 56515
IMPORTANT SAFETY INFORMATION
Assembly Precautions
1. Assemble only according to these instructions.
Improper assembly can create hazards.
2. Tighten Nuts used for assembly securely,
but do not damage the product.
3. Wear ANSI-approved safety goggles during assembly.
4. Keep assembly area clean and well lit.
5. Keep bystanders, including children,
out of the area during assembly.
6. Do not assemble when tired or when under the
influence of alcohol, drugs or medication.
7. Do not allow children to play with this
product until it is completely assembled.
Use Precautions
1. Do not allow children to climb, stand, or sit on
any part of this item. It can suddenly tip over.
2. Supervise children at all times while
they are playing with this item.
3. Do not allow children to
disassemble the Workbench.
4. Place the Workbench on a solid, level, even
surface before allowing it to be played with.
5. Use as intended only. This product is a toy and
should not be used for any other purpose.
6. Inspect before every use. Do not allow use if parts
are not properly secured or parts are damaged.
7. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.

Page 3For technical questions, please call 1-888-866-5797.56515
Assembly Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
1. Connect the Tray (C) between the two Leg Pairs (B)
at an angle using the Nuts (Q) as shown.
Note that the finished side of each Leg Pair
should be on the outside of the assembly,
and the feet should be pointed downward.
Figure A
2. Place the Tabletop (A) upside-down on the floor.
Press the top of the Leg Pair assembly into the
rectangular holes in the underside of the Tabletop.
After you are sure all four corners align properly,
press each of them in until you hear a click on
each corner. Confirm that the Leg Pair assembly is
securely attached to the Tabletop at all four corners.
Figure B
3. Turn the Tabletop and Leg assembly
upright on a stable surface.
4. Align the Vise (T) with the four holes on the right end
of the Tabletop. Secure it in place using 4 Bolts (N).
T
Figure C
5. Insert the Pegboard (D) securely into the holes on the
Tabletop until both ends click into place. Make sure
that the Pegboard is securely attached on both ends.
Figure D

Page 4 For technical questions, please call 1-888-866-5797. 56515
6. Insert the threaded end of the Drill (J) through
the slot on the left side of the Pegboard. Secure
in the back of the Pegboard using a Nut (Q).
Figure E
7. CAUTION! Check that all connections are
secure and all hardware is tight. Hardware used
for assembly should be as tight as possible
without damaging the product or its fasteners.
8. An example setup for this product is shown below.
Figure F

Page 5For technical questions, please call 1-888-866-5797.56515
Usage Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
CAUTION! TO PREVENT INJURY AND PRODUCT FAILURE:
Inspect before every use. Do not allow use if parts are not properly secured or parts are damaged.
1. Place the Workbench on a solid, level, even
surface before allowing it to be played with.
2. Do not allow children to climb, stand, or sit on
any part of this item. It can suddenly tip over.
3. Supervise children at all times while
they are playing with this item.
4. Do not allow children to
disassemble the Workbench.
5. Use as intended only. This product is a toy and
should not be used for any other purpose.

Page 6 For technical questions, please call 1-888-866-5797. 56515
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Page 7For technical questions, please call 1-888-866-5797.56515
Parts List and Diagram
Part Description Qty
A Tabletop 1
B Leg Pair 2
C Tray 1
D Pegboard 1
E Saw 1
F Wrench 1
G Hammer 1
H Screwdriver 1
I Planer 1
J Drill 1
Part Description Qty
K Big Workpiece 1
L Small Workpiece 2
M Peg 5
N Bolt 8
O Nail 6
P Connecting Belt 1
Q Nut 10
S Lid 1
T Vise 1
U Ring Peg 1
UT
Record Serial Number Here:
Note: If product has no serial number, record
month and year of purchase instead.
Note: Some parts are listed and shown
for illustration purposes only, and are not
available individually as replacement parts.
Specify UPC 193175491633 when ordering parts.

26677 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.