Harmonic XOS User manual

Warner Media - XOS - Quick Start Guide
C. Power on the Laptop.
- In a web browser (Google Chrome), type the IP address ( https://192.0.2.2 )
and press Enter.
D. Enter the following credentials and click Log in:
- Login: xos
- Password: xos-user
E. Select the Platform Configuration tile and click Launch.
F. Select the Network tab followed by the IP config tab.
G. You can change the IP parameters for the following ports
based on your IP plan or keep the default IP addresses:
- Management 01 port (GbE01 – Default: 192.168.1.200)
- Data GbE03 port (Default: 192.168.2.200)
H. Click Save.
I. Remove the USB-Ethernet adapter from the front panel of
the XOS.
J. Install the front bezel.
Contacting Harmonic:
WM‐CBAND‐HEL[email protected]
1. Unpacking and Racking 2. Cabling
Quantity Description
1 XOSServer‐1UHPEDL360G10
2Powercable
8MicroBNCtoBNCcable
1 Frontbezel
1 Rackmountingkitfor1UHPEDL360G10
1 USBtoEthernetadapter
1 QuickStartGuide
A. Please use this list to ensure that your order is complete.
B. Remove the XOS and associated accessories from the
box.
C. Mount the XOS in the rack.
The XOS can be mounted in a 19" rack.
- Ensure that it is secured in the rack.
- Maintain air flow around the XOS.
- Do not place another device directly on the top of the XOS.
3. Configure IP addresses
A. Follow the diagram below to perform the XOS cabling.
A. Use the USB to Ethernet adapter to connect a laptop to
the USB port on the front panel as shown below:
B. Power on the XOS.
- Connect the power cord to the power supply on the rear panel.
- Connect the cable to the power source and turn on the power.
- Wait for the XOS to complete the boot process.
- The Management and Data switches are not
pprovided by Harmonic
- The Management PC is recommended
If you don’t have a Management PC, keep the laptop
connected until you complete the configuration (Step 6).

The XOS will perform a software and configuration update upon a successful
connection to RF. This process is automatic and controlled by the DMS at Warner
Media.
Once the software and configuration updates complete, do the following:
A. Select the Configure Broadcast tile and click Launch.
The display will be similar to the picture on the right:
- The message at the top of the user interface (UI) specifies DMS is controlling the
XOS.
- The left side of the UI shows the RF tuners and the number of associated
programs.
- The right side of the UI shows the Multiplexers associated to each tuner.
B. Click on a multiplexer to expand the display for the list of
authorized programs.
4. Checking the RF connection
6. Final steps for configuration
8. Documentation
Depending on the RF connection and the Distribution Management System
(DMS) configuration,either a Connected or a Controlled message will
appear at the top of the user interface:
5. Waiting for Upgrade & Configuration
7. Checking XOS outputs
This initialization step can take few hours. Make sure the XOS remains
powered on and connected to Satellite RF.
A. Assign a Multiplexer to an IP output.
1 - Select a Multiplexer and click Edit.
2 - Set the multicast IP Address according to your IP plan.
3 - Select the IP data port (typically GbE03).
4 - Set the UDP port number according to your IP plan.
5 - By default, the Primary IP output is muted. Clear the check box to
tttunmute the ouput.
6 - Click Update to commit your changes.
B. If required, assign a Multiplexer to an ASI output.
1 - Select a Multiplexer and click Edit.
2 - Click
+ button.
3 - Select ASI.
4 - Enter the ASI port to be used.
5 - Click Update to commit your changes.
The full user guide and other documentation are available at:
https://harmonicinc.com/documentation/warner-media/
A. Connect a professional-grade decoder to the XOS.
B. Connect the decoder to the HDMI port on the TV.
C. Power on the decoder and the TV.
- The presence of a Multiplexer from the ASI input is automatically detected by
the decoder.
- The first program appears,
- To receive a Multiplexer via the data switch, enter the same IP address you
entered in the XOS (See to Step 6. A. Assign a Multiplexer to an IP output).
Refer to the decoder documentation for additional information.
If a message appears in red, the connection is not yet established.
Please check your RF reception level and wiring.