Harmony GENESYS User manual

®Harmony Juvenile Products HMYGENHBB-UK1 19/12 UK
GENESYS
CAR SEAT
INSTRUCTION MANUAL
STOP
READ THIS MANUAL
Do not install or use this child restraint until you read and understand
the instructions in this manual and in your vehicle owner’s manual.
FAILURE TO PROPERLY USE THIS CHILD RESTRAINT INCREASES THE
RISK OF SERIOUS INJURY OR DEATH IN A SHARP TURN, SUDDEN
STOP OR CRASH.
IF YOU HAVE ANY PROBLEMS, PLEASE DO NOT RETURN
THIS PRODUCT TO THE PLACE OF PURCHASE. PLEASE
CONTACT CUSTOMER SERVICE AT [phone]
OR AT WWW.HARMONYJUVENILE.COM
This child restraint complies with ECE regulations for use by children:
• Group I / II / III
• Mass: 9 to 36 kg
Suitable for children from 9 to 18 kg (with built-in harness)
Suitable for children from 15 to 36 kg (as high-back booster)
For children approx. 9 months - 12 years

2
REGISTRATION INFORMATION
REGISTER YOUR CHILD RESTRAINT TODAY! Child restraints could be recalled for
safety reasons. You must register this restraint to be reached in a recall, and to be
eligible to receive replacement parts while under warranty.
The model number, serial number and manufacturing date can be found on a label
on the underside of the child restraint.
Visit www.harmonyjuvenile.com/uk/register to register your child restraint
online, mail-in the registration card or send your name, address, the restraint’s
model number, manufacturing date and date of purchase to:
Harmony Juvenile Products UK
10 Beach Priory Gdns.
Southport, UK
PR8 1RT
or call: [phone]
For recall information, any questions you may have, or to make a change of address
or contact information please call Customer Service at [phone] or visit
us online at www.harmonyjuvenile.com.
PLEASE DO NOT SEND IN YOUR REGISTRATION CARD IF
YOU HAVE REGISTERED YOUR RESTRAINT ONLINE.
IF YOU NEED HELP
Please fill in the information below for future reference. The model number and
manufacturing date can be found on a label on the underside of the child restraint.
Model Number: ___________________________________________________________
Manufacture Date: ________________________________________________________
Date of Purchase: _________________________________________________________
Our Customer Service Department is standing by to help you with any questions or
concerns you may have regarding installation, use, care and/or parts. Please have
your product’s model number and manufacturing date available when contacting us.

3
A
I
J
D
H
PARTS LIST
Headrest fabric cover (pre-installed)
Backrest fabric cover (pre-installed)
Base fabric cover (pre-installed)
Harness straps, buckle and clips
Shoulder pads
Crotch strap and pad
1-hand headrest height adjustment
handle (under headrest fabric)
Harness metal adjustment button
(above strap, under fabric)
Up-front harness adjustment strap
Infant insert pad
Harness splitter plate
Mesh storage pouch
Backrest plate
Locking clip
A
B
C
D
E
F
G
N
TO PURCHASE REPLACEMENT PARTS:
In the United Kingdom, please contact us at
www.harmonyjuvenile.com
or by calling [phone].
B
H
I
J
K
L
G
M
N
E
F
L
K
M
C

4
PREPARING CHILD RESTRAINT FOR USE
1 2
3
2

5
ADJUSTING CROTCH STRAP POSITION
4 5
INSTALLING WITH VEHICLE SEAT BELT
GROUP 1 (9 - 18 KG)
6

7


6
8 9
10 11

7
12 13
14
USING CHILD RESTRAINT WITH BUILT-IN HARNESS
15 16
17

8
18 19
PREPARING BOOSTER SEAT FOR USE
23 24
25
20 21 22

9
26
SECURING CHILD AND BOOSTER SEAT IN VEHICLE
27 28 29
30 31 32
INSTALLING WITH VEHICLE SEAT BELT
GROUP 2 & 3 (15 - 36 KG)
33

10
REMOVING/INSTALLING FABRIC SEAT COVER
34 35
CERTIFICATIONS
This is a “Universal” child restraint when installed using the 3-point vehicle seat
belt only. It is approved to the requirements of the European Standard for Child
Safety Seat Equipment under Regulation No. 44, 04 series of amendments, for
general use in vehicles and it will fit most, but not all, car seats.
A correct fit is likely if the vehicle manufacturer has declared in the vehicle
handbook that the vehicle is capable of accepting a “Universal” child restraint for
this age group.
This child restraint has been classified as “Universal” under more stringent
conditions than those which applied to earlier designs which do not carry this
notice.
If in doubt, consult either the child restraint manufacturer or the retailer.
! Only suitable for use in the listed vehicles fitted with 3-point with retractor safety-
belts, approved to ECE Regulation No. 16 or other equivalent standards.
This restraint is NOT CERTIFIED for aircraft use.
This child restraint must NOT be used in homes, boats, buses, motorcycles, motor
homes, or any other vehicles that have non-forward-facing seats, missing seat
belts, or whose seat belts do not meet the requirements of this child restraint.

11
PREPARING CHILD RESTRAINT FOR USE
! ENSURE the harness height is correct for your child’s size. VERIFY OFTEN (1).
1. Loosen harness system by pushing the up-front metal harness adjuster at the front of
the seat JUST ABOVE the adjustment strap (under the fabric) and by simultaneously
pulling the chest harness straps towards you (2).
TIP: PULL ON THE HARNESS STRAPS. DO NOT PULL ON THE SHOULDER
PADS AS THEY ARE LOCKED IN PLACE.
2. To determine what harness height is appropriate for your child, have your child sit
in the child restraint with their back flat against the backrest.
3. Reach into the opening on the top of the headrest fabric cover and find the RED
one-hand headrest height adjustment button.
4. Squeeze button and lift the headrest until the shoulder straps are at or just
above your child’s shoulders (3). The child restraint has NINE headrest height
adjustments.
5. Release the button and listen for a ‘click’ to make sure harness is locked in place.
! WARNING: To ensure headrest is locked in position, gently push
down on headrest.
! ENSURE BOTH HARNESS STRAPS ARE PROPERLY SECURED
ON THE SPLITTER PLATE.
! WARNING: The shoulder harness must be EVEN OR SLIGHTLY
ABOVE the child’s shoulders (A). If the upper most harness
position is below the child’s shoulders, DO NOT use this child
restraint with harness.
! WARNING: DO NOT use this child restraint if the midpoint
of your child’s head is above the top of the child restraint’s
headrest at its maximum height (B).
REMEMBER to check the shoulder straps position frequently
and move them to the next position when necessary. The
harness straps MUST be in the height position EVEN WITH or
just ABOVE the shoulders. The harness pads and crotch pads
are optional and are not a safety feature.
WARNING!
!
INCORRECT USE OF THE HARNESS SYSTEM IS THE MOST COMMON
MISTAKE PEOPLE MAKE. IT IS VERY IMPORTANT TO READ, UNDERSTAND
AND FOLLOW ALL INSTRUCTIONS AND WARNINGS. DO NOT MISTAKE
COMFORT FOR SAFETY. THE HARNESS SYSTEM MUST BE SNUGLY
ADJUSTED AT ALL TIMES.
ADJUSTING HARNESS SHOULDER STRAPS
A
B

12
The crotch strap has two (2) positions.
1. Remove fabric crotch pad.
2. Push the buckle down through the fabric seat cover towards the plastic base of
the child restraint.
3. Lift the fabric seat cover on the base of the child restraint to expose the buckle
and slot positions.
4. Guide the crotch strap through the plastic base to the desired slot position (4).
! ENSURE that the strap is COMPLETELY in the desired slot and the harness strap
is NOT twisted. Gently pull upwards to ensure it is firmly in place.
! ENSURE that the buckle is facing FORWARD (5).
5. Push the buckle upwards through the fabric seat cover.
6. Replace fabric seat cover and fabric crotch pad.
! Use ONLY the vehicle’s 3-point lap-and-shoulder belt system when restraining this
child restraint to the vehicle (6). DO NOT use this child restraint with a 2-point
vehicle belt (7). Your child would be seriously injured in the event of a crash.
1. Place the child restraint flush against a forward-facing vehicle seat. The vehicle
seat MUST be equipped with a 3-point lap-and-shoulder belt. The child restraint
must be level, stable and not rock side-to-side.
2. Thread the vehicle shoulder belt portion of the seat belt behind the headrest ON
THE SAME SIDE as the seat belt retractor (8).
3. Open harness system and lift insert cushion. Thread the lap portion of the
WARNING!
!
FAILURE TO REINSTALL THE HARNESS STRAPS CORRECTLY COULD
RESULT IN SERIOUS INJURY OR DEATH.
ADJUSTING CROTCH STRAP POSITION
WARNING!
!
FAILURE TO REINSTALL THE CROTCH STRAPS CORRECTLY COULD RESULT
IN SERIOUS INJURY OR DEATH.
INSTALLING WITH VEHICLE SEAT BELT
GROUP 1 (9 - 18 KG)

13
vehicle’s seat belt through the red belt base positioning guide ON THE SAME
SIDE as the seat belt retractor (8). Replace insert cushion.
4. From BEHIND the child restraint, pass both the lap and shoulder portions around
the rear of the seat and back through the opening (8) on the opposite side of
the seat as indicated (9). Take both portions of the vehicle seat belt and guide
them over the side of the child restraint (10).
5. Buckle the vehicle seat belt. Listen for an audible “click” (8). The vehicle seat belt
MUST NOT be twisted.
6. If your vehicle is equipped with a ELR/ALR switchable seat belt retractor system,
we recommend that you pull out the full length of the vehicle seat belt (until you
cannot pull out any more slack). This locks the retractor. If not equipped with
switchable ELR/ALR retractor, continue with step #7.
7. Tighten vehicle seat belt by placing your knee on the child restraint base and
by using your full weight to push the child restraint down as you simultaneously
release the extra belt length until seat belt is taught and has no slack (12).
Manually pull out of all of the slack from the LAP PORTION (11) and then feed
the shoulder portion back into the retractor.
8. Attach the locking clip around both lap and shoulder belts once vehicle seat belt
is adjusted and tightened (13, 14).
For more information on how to tighten the seat belt for your seat belt system, see
your vehicle owner’s manual.
! Incorrect use of the harness system is the most common mistake people make. It
is VERY important to read, understand and follow ALL instructions and warnings.
DO NOT mistake comfort for safety. The harness system MUST be snugly adjusted
at all times.
! Snugly adjust the harness provided with this child restraint around your child. A
snug strap is one with no slack. It should not press on the child’s flesh or cause
your child’s body to be in an unnatural position. You should only be able to slide
ONE FINGER between the shoulder straps and the child’s shoulder.
! Avoid unnecessary bulky clothing.
USING CHILD RESTRAINT WITH BUILT-IN HARNESS
WARNING!
!
FAILURE TO FASTEN AND TIGHTEN THE HARNESS SYSTEM CORRECTLY MAY
CAUSE THE CHILD TO BE EJECTED FROM THE RESTRAINT SYSTEM IN CASE
OF A SHARP TURN, SUDDEN STOP OR CRASH CAUSING SERIOUS INJURY
OR DEATH. In a crash, the child restraint will provide NO protection for your child
unless the harness straps are properly secured. DO NOT mistake comfort for safety.
Harness system MUST be snugly adjusted. Follow these instructions carefully.

14
1. To loosen the harness strap: Push the up-front metal harness adjuster at the
front of the seat just ABOVE the adjustment strap (UNDER THE FABRIC) and
simultaneously pull the chest strap towards you (15).
TIP: PULL ON THE HARNESS STRAPS. DO NOT PULL ON THE SHOULDER
PADS AS THEY ARE LOCKED IN PLACE.
2. Unbuckle harness straps by pressing on the RED buckle release button and by
pulling the buckle clips out (16). Move harness straps to the side.
3. Place child in child restraint with child’s back flat against back of the backrest.
4. Adjust headrest height (see “Adjusting harness shoulder straps”).
5. Place harness straps over child’s shoulders. Hold the two buckle clips together
and insert the two-piece buckle clip into buckle until they ‘click’ into place (17).
! ENSURE that the buckle is properly fastened by gently tugging on it.
! ENSURE that the straps are NOT twisted.
! DO NOT use child restraint if harness does not lock.
6. Tighten harness system by gently pulling on the up-front harness adjuster strap
until all slack is removed from the system (18).
!ENSURE straps are flat and snug against child’s shoulders and thighs. You should
NOT be able to slide more than one finger between the strap and the child’s
shoulder (19).
A snug strap should not allow any slack. It lies in a relatively straight line without
sagging. It should not press the child’s flesh or cause your child’s body to be in an
unnatural position.
! Any straps holding the restraint to the vehicle should be tight, any straps
restraining the child should be adjusted to the child’s body, and all straps should
not be twisted.
1. Loosen the harness system by pressing on the up-front metal harness adjuster
(UNDER THE FABRIC), and simultaneously pulling the shoulder straps towards you.
2. Unbuckle harness by pressing on the RED buckle release button.
IF YOUR CHILD HAS REACHED 15 KG, YOU CAN USE THE SEAT IN BOOSTER MODE.
!DO NOT use infant insert in booster mode.
Harmony Juvenile Products advises that your child remains in a 5-point harness for as
long as possible per the mass and height requirements of the child restraint.
1. Open harness buckle.
SECURING CHILD IN CHILD RESTRAINT
REMOVING CHILD FROM CHILD RESTRAINT
USING CHILD RESTRAINT IN BOOSTER MODE
(WITHOUT BUILT-IN HARNESS)

15
2. Face the rear of the child restraint and remove the harness straps from the splitter
plate (20, 21).
3. Pull harness straps out of their respective slots in the backrest (22).
4. Lie child restraint on its side and find the metal locking plate for each harness
strap on the underside of the base of the child restraint. Grasp the strap and turn
each metal plate (23) so that it can slide up and out through the plastic seat
base (25).
5. Repeat procedure for crotch strap (24) and Top Tether removal.
6. Store complete harness system for future use.
7. Pull the up-front harness adjustment strap as far as it will go. This will lock the
splitter plate into the base of the seat.
8. Roll strap tightly, secure roll with an elastic band and store rolled strap under the
fabric seat cover in the opening of the up-front adjuster.
To reinstall, remove backrest plate and repeat these steps in reverse order. When
re-inserting the shoulder straps through the backrest, ensure the straps are
ABOVE the metal bars inside the slots in the backrest. Reinstall backrest plate
once harness is properly reinstalled.
!ENSURE the vehicle shoulder belt’s position is correct for your
child’s size. VERIFY OFTEN.
! WARNING: DO NOT use this booster seat if the midpoint of
your child’s head is above the top of the booster seat headrest
at its maximum height.
PREPARING BOOSTER SEAT FOR USE
WARNING!
!
INCORRECT USE OF THE VEHICLE’S 3-POINT LAP-AND-SHOULDER SEAT
BELT SYSTEM IS THE MOST COMMON MISTAKE PEOPLE MAKE. IT IS VERY
IMPORTANT TO READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS
AND WARNINGS. DO NOT MISTAKE COMFORT FOR SAFETY. THE
VEHICLE’S 3-POINT LAP-AND-SHOULDER SEAT BELT MUST BE SNUGLY
ADJUSTED AT ALL TIMES.
WARNING!
!
FAILURE TO REINSTALL THE HARNESS SYSTEM AND CROTCH STRAP
CORRECTLY COULD RESULT IN SERIOUS INJURY OR DEATH.

16
!DO NOT use this booster seat if it can’t be properly leveled, stabilized, and installed
as per this instruction manual. It is possible that your vehicle has no suitable seating
position for this booster seat due to seating surface, seat belt type and/or airbag
system. Read and follow these instructions, and your vehicle owner’s manual carefully.
! WARNING: You MUST use the vehicle 3-point lap-and-shoulder belt system when
restraining the child in the booster seat (26).
! WARNING: Vehicle belts MUST be tight, adjusted to the child’s body, and should
not be twisted (26).
! NEVER use a vehicle lap-only belt to secure child in booster seat (27).
! NEVER USE A LOOSE SHOULDER BELT.
! NEVER position the shoulder belt under the child’s arm (28) or place the
shoulder belt behind the child’s back (29).
Lap portion of lap-and-shoulder belt MUST be low and snug across the hips,
with the pelvis firmly engaged, just touching the child’s thighs. The lap
WARNING!
!
!ALWAYS ASSIST YOUR CHILD WHEN GETTING INTO
AND OUT OF YOUR CHILD RESTRAINT/BOOSTER SEAT.
!NEVER LET YOUR CHILD LEAN ON THE ARMREST WHEN
GETTING INTO OR EXITING THE BOOSTER SEAT TO PREVENT
THE SEAT FROM TIPPING.
! ENSURE THATTHE BOOSTER SEAT IS LEVEL, STABLE AND
DOES NOT ROCK SIDE-TO-SIDE. IF THE BOOSTER SEAT
IS NOT STABLE, TRY ANOTHER SEATING LOCATION. IN
VEHICLES WITH WIDE, FLAT SEATS, A ROLLED TOWEL
CAN BE USED ON THE OUTBOARD (DOOR) SIDE TO ADD STABILITY TO THE
BOOSTER SEAT.
! DO NOT ADD ANYTHING BEHIND OR UNDER THE BOOSTER SEAT.
SECURING CHILD AND BOOSTER SEAT IN VEHICLE
WARNING!
!
FAILURE TO PROPERLY SECURE YOUR CHILD IN THE BOOSTER SEAT
INCREASES THE RISK OF SERIOUS INJURY OR DEATH IN THE EVENT OF A
SHARP TURN, SUDDEN STOP OR CRASH. In a crash, the booster seat provides
NO protection for your child unless the vehicle 3-point lap-and-shoulder belt is
properly secured. Follow these instructions carefully to properly secure your child.

17
portion MUST NOT be lying across the child’s stomach as this can cause major
injuries to the child in case of a sharp turn, sudden stop or crash.
! DO NOT allow the child to slouch, slide down in the seat, or create slack in the
belt system (30). If child will not keep vehicle belt properly positioned, DO NOT
use this booster seat.
! DO NOT position vehicle belt over top of the armrests (31).
! The vehicle seat headrest should not create a gap between vehicle seat and
booster seat (32). If so, remove the vehicle headrest.
! DO NOT use any load bearing contact points other than those described in the
instructions and marked in the child restraint.
IF IN DOUBT ABOUT THESE POINTS OR ANY QUESTIONS RELATED TO
INSTALLATION, PLEASE CONTACT HARMONY JUVENILE PRODUCTS.
1. Place the booster seat flush against a forward-facing vehicle seat. The vehicle seat
MUST be equipped with a 3-point lap-and-shoulder belt. Booster must be level,
stable and not rock side-to-side (33).
2. Place child in the booster seat with child’s back flat against the back of the
booster seat.
3. Adjust headrest height (see “Adjusting harness shoulder straps”).
4. Thread shoulder belt portion of the 3-point lap-and-shoulder belt system behind
the headrest ON THE SAME SIDE as the seat belt retractor (33) and ensure
that shoulder belt lies across child’s shoulder and chest, and NOT across child’s
face or neck.
5. Thread both sides of the lap belt under BOTH armrests. Thread the lower
end of the shoulder belt under the armrest on the buckle side (43). ENSURE
that the belt is snug across the child’s hips. It is important to ensure that
any lap strap is worn low down, so that the pelvis is firmly engaged, just
touching their thighs and is NOT across their stomach.
INSTALLING WITH VEHICLE SEAT BELT
GROUP 2 & 3 (15 - 36 KG)
WARNING!
!
DUE TO VARYING ANGLES OF VEHICLE SEAT BELT RETRACTORS,
EXCESS SLACK IN THE VEHICLE BELT SYSTEM MIGHT NOT BE REMOVED
AUTOMATICALLY. Once the lap and shoulder portions of the seat belt are
properly positioned and the buckle is attached, FEED ANY REMAINING
SLACK OF THE SEAT BELT MANUALLY BACK INTO THE RETRACTOR TO
TIGHTEN THE WHOLE SYSTEM.

18
7. Buckle the vehicle seat belt into place and ensure it is secure by gently pulling
on it.
! BOTH SIDES OF THE LAP BELT MUST PASS UNDER BOTH ARMRESTS, AND
THE LOWER END OF THE SHOULDER BELT MUST PASS UNDER THE ARMREST
ON THE BUCKLE SIDE.
! Any straps holding the restraint to the vehicle should be tight, any straps
restraining the child should be adjusted to the child’s body, and all straps should
not be twisted.
! NEVER USE A VEHICLE LAP-ONLY BELT WHEN USING THIS BOOSTER SEAT.
TO REMOVE
Remove harness system.
HEADREST:
1. Gently slide fabric downwards off the top of the headrest. (34).
BACKREST:
1. Undo the fabric hook-and-loop fastener tabs (x2) (35) along the bottom sides
of the backrest (where the backrest meets the base).
2. Gently slide fabric cover off the backrest.
3. Remove EPE foam from backrest fabric.
BASE:
1. Undo the snaps (x2) behind the seat (35) as indicated.
2. Gently slide the fabric cover off the plastic base from the back of the child
restraint towards the front of the seat.
TO INSTALL
To reinstall fabric covers, repeat previous steps in reverse order.
! CAUTION: Reinstall harness system if applicable.
We recommend that you store your instruction manual in the mesh pocket
provided under the fabric on the side of the child restraint.
REMOVING/INSTALLING FABRIC SEAT COVER
INSTRUCTION MANUAL STORAGE

19
WARNINGS
The safety of your child and the effectiveness of this child restraint depend on:
1. Selecting a suitable location for the child restraint in your vehicle.
2. Properly routing the vehicle seat belt.
3. Properly securing both your child and the child restraint in the vehicle.
Many seat belts are NOT safe to use with this child restraint. If in doubt about
installing this child restraint, consult the vehicle owner’s manual or call the
Harmony Customer Service Department.
Follow all labels on this child restraint and in these written instructions. DO
NOT INSTALL OR USE THIS CHILD RESTRAINT UNTIL YOU READ AND
UNDERSTAND THE INSTRUCTIONS IN THIS MANUAL AND IN YOUR VEHICLE
OWNER’S MANUAL.
WARNING!
!
GENERAL WARNINGS
WARNING!
!
FAILURE TO PROPERLY READ, FOLLOW AND USE THESE INSTRUCTIONS
AND THE CHILD RESTRAINT LABELS INCREASES THE RISK OF SERIOUS
INJURY OR DEATH IN A SHARP TURN, SUDDEN STOP OR CRASH. Your
child’s safety depends on the proper installation and use of this child restraint.
Even if this child restraint seems easy to install and use, it is VERY IMPORTANT
to read and understand these instructions and the vehicle owner’s manual.
NO CHILD RESTRAINT CAN GUARANTEE PROTECTION WHEN THE VEHICLE
IS SERIOUSLY IMPACTED. However, when correctly installed, a child restraint
will substantially improve the chances for survival and reduce the risk of serious
injury in most crashes.
Carefully follow the instructions in this manual and in your vehicle owner’s
manual. If there is a discrepancy between the two, the vehicle owner’s manual
must take precedence with regards to seat belts and/or airbags.
! DO NOT allow children to play with this child restraint.
!NEVER leave children alone in a vehicle under any circumstance.
!It is recommended that children are not left in their child restraint system unattended.
! Set a good example by ALWAYS wearing your seat belt. Make it a firm rule
that the vehicle does not move until everyone is buckled up. MAKE NO
EXCEPTIONS.

20
! Harmony Juvenile Products advises against loaning or passing along a child
restraint. DO NOT USE A SECOND-HAND CHILD RESTRAINT or a child restraint
whose history you do not know.
! When disposing a child restraint system, ensure to dispose of the unit in a way
others cannot reuse it (e.g. use a dark trash bag, do not sell to a thrift shop or in
a garage sale, etc.).
! Store the child restraint in a safe place when not in use. DO NOT place heavy
objects on top of the child restraint while in storage.
! DO NOT remove any stickers or warnings as they contain important information.
According to accident statistics, CHILDREN ARE SAFER WHEN PROPERLY
RESTRAINED IN THE REAR SEATING POSITIONS THAN IN THE FRONT
SEATING POSITION.
! DO NOT use any load bearing contact points other than those described in the
instructions and marked in the child restraint.
! DO NOT allow others to install or use this child restraint unless they read and
understand all the instructions and labels.
! DO NOT GIVE THIS CHILD RESTRAINT to someone else without also giving
them this instruction manual. Additional instruction manuals can be downloaded
directly from www.harmonyjuvenile.com.
! To ensure proper child restraint use, keep and store this instruction manual and
refer to it when necessary.
! DO NOT LEAVE A CHILD RESTRAINT UNSECURED IN YOUR VEHICLE. In a
collision, sharp turn or sudden stop, an unsecured child restraint can injure other
occupants. Remove it or make sure that it is securely attached with the vehicle seat
belt, even when not in use.
WARNING!
!
!ALWAYS ASSIST YOUR CHILD WHEN GETTING INTO AND OUT OF THE
CHILD RESTRAINT.
! ENSURE THAT THE CHILD RESTRAINT IS LEVEL, STABLE AND DOES
NOT ROCK SIDE-TO-SIDE. IF THE CHILD RESTRAINT IS NOT STABLE, TRY
ANOTHER SEATING LOCATION.
! DO NOT ADD ANYTHING BEHIND OR UNDER THE CHILD RESTRAINT.
USAGE WARNINGS