Hatco FLAV-R-SAVOR FSD Series User manual

© 2010 Hatco Corporation
#-)*-&)i
F>:5:7:65@=5:?82?5:DA=2J23:?6ED
*2?5*+*6C:6D
?DE2==2E:@?2?5&A6C2E:?8$2?F2=
@C 2?5%@? $@56=D
I&W #07.05.160.00
Bewaar- en uitstelkasten met vochtregeling
Modelreeksen FSD en FSDT
Handleiding voor Installatie en Bediening
'
Vitrinas de Calor y Humedad
Series FSD y FSDT
Manual de Instalación y Operación
'
spositori con regolazione di
temperatura ed umidità
Serie FSD e FSDT
Manuale per l'installazione e l'uso
'
Ausstellungsvitrinen mit Wärme-
und Feuchtigkeitsregelung
Serien FSD und FSDT
Installations- und Bedienungshandbuch
'
Armoires de présentation chauffées et humides
Séries FSD et FSDT
Manuel d'installation et d'utilisation
'
)68:DE6CJ@FCF?:E@?=:?6
See IMPORTANT OWN R INFORMATION
for more information.

This manual provides installation, safety, and operating
instructions for Hatco Humidified Holding and Display Cabinets.
Hatco recommends all installation, operating, and safety
instructions appearing in this manual be read prior to installation
or operation of a unit.
Safety information that appears in this manual is identified by
the following signal word panels:
.)% % :?5:42E6D 2 92K2C5@FD D:EF2E:@? H9:49 :7 ?@E
2G@:5654@F=5C6DF=E:?562E9@CD6C:@FD:?;FCJ
,+ &% :?5:42E6D 2 92K2C5@FD D:EF2E:@? H9:49 :7 ?@E
2G@:5654@F=5C6DF=E:?>:?@C@C>@56C2E6:?;FCJ
%&+ :DFD65E@255C6DDAC24E:46D?@EC6=2E65E@A6CD@?2=
:?;FCJ
NOTICE
CAUTION
WARNING
%+)&,+ &%
Hatco Flav-R-Savor®Humidified Holding and Display Cabinets
are designed to hold prepared foods for prolonged periods of
time while maintaining that “just-made” quality. Hatco
Humidified Holding and Display Cabinets provide the best
environment for food products by regulating the air temperature
while at the same time balancing the humidity level. The use of
controlled moisturized heat maintains serving temperature and
texture longer than conventional dry holding equipment.
Flav-R-Savor air flow pattern is designed to maintain consistent
cabinet temperature without drying out foods. The precise
combination of heat and humidity creates a “blanket” effect
around the food. The air flow rate enables the cabinet to
recover temperature rapidly after opening and closing the door.
Hatco Humidified Holding and Display Cabinets are products of
extensive research and field testing. The materials used were
selected for maximum durability, attractive appearance and
optimum performance. very unit is inspected and tested
thoroughly prior to shipment.
>A@CE2?E&H?6C ?7@C>2E:@? 
?EC@5F4E:@?
>A@CE2?E*276EJ ?7@C>2E:@?
$@56=6D4C:AE:@?
$@56=6D:8?2E:@?
*A64:7:42E:@?D 
Dimensions......................................................................5
Plug Configurations .........................................................5
lectrical Rating Chart.....................................................6
?DE2==2E:@?
General............................................................................7
Reversing the Access Door .............................................8
Relocating the Proximity Switch ......................................9
&A6C2E:@?
General..........................................................................10
Setting the Air Temperature ...........................................10
Setting the Humidity Level.............................................10
Food Holding Guide.......................................................11
$2:?E6?2?46 
General ..........................................................................11
Cleaning.........................................................................11
Removing the Rotating Rack.........................................12
Removing the Glass Panels ..........................................12
Draining the Water Reservoir ........................................12
Removing Lime and Mineral Deposits...........................12
Replacing a Display Light ..............................................13
&AE:@?D2?5446DD@C:6D
+C@F3=6D9@@E:?8F:56 
?E6C?2E:@?2=#:>:E65.2CC2?EJ 
*6CG:46 ?7@C>2E:@? 
$'&)+%+&.%) %&)$+ &%
Record the model number, serial number (specification label
located on the ceiling sheet inside the unit), voltage, and
purchase date of the unit in the spaces below. Please have this
information available when calling Hatco for service assistance.
Model No. ____________________________________
Serial No. ____________________________________
Voltage ______________________________________
Date of Purchase ______________________________
)68:DE6CJ@FCF?:E
Completing online warranty registration will prevent delay in
obtaining warranty coverage. Access the Hatco website at
HHH92E4@4@CA4@>, select the Parts & Service pull-down
menu, and click on “Warranty Registration”.
Business 8:00 AM to 5:00 PM
Hours: Central Standard Time (C.S.T.)
(Summer Hours: June to September—
8:00 AM to 5:00 PM C.S.T.
Monday through Thursday
8:00 AM to 2:30 PM C.S.T. Friday)
Telephone: [phone]
-mail: [email protected]
Fax: [phone] (Parts and Service)
Additional information can be found by visiting our web site at
HHH92E4@4@CA4@>.
2Form No. FSDC M-1010
&%+%+*

$'&)+%+*+0 %&)$+ &%
+9:DF?:E:D?@E:?E6?5657@CFD63J49:=5C6?@CA6CD@?D
H:E9 C65F465 A9JD:42= D6?D@CJ @C >6?E2= 42A23:=:E:6D
?DFC6AC@A6CDFA6CG:D:@?@749:=5C6?2?5<66AE96>2H2J
7C@>E96F?:E
$2<6DFC62==@A6C2E@CD92G6366?:?DECF4E65@?E96D276
2?5AC@A6CFD6@7E96F?:E
$2<6DFC6 7@@5AC@5F4E92D 366?962E65E@E96 AC@A6C
7@@5D276E6>A6C2EFC6367@C6 A=24:?8 :? F?:E 2:=FC6 E@
962E7@@5AC@5F4EAC@A6C=J>2JC6DF=E:?D6C:@FD962=E9
C:D<D+9:DF?:E:D7@C9@=5:?8AC6962E657@@5AC@5F4E@?=J
2E4@ :D ?@E C6DA@?D:3=6 7@C E96 24EF2= 7@@5 AC@5F4E
D6CG:?8E6>A6C2EFC6 E:DE96C6DA@?D:3:=:EJ@7E96FD6CE@
6?DFC6E92EE967@@5AC@5F4E:D96=52?5D6CG652E2D276
E6>A6C2EFC6
,)%1)*@>66IE6C:@CDFC7246D@?E96F?:EH:==86E
9@E,D642FE:@?H96?E@F49:?8E96D62C62D
#@42E6F?:E2EE96AC@A6C4@F?E6C96:89E:?2?2C62E92E:D
4@?G6?:6?E7@CFD6+96=@42E:@?D9@F=536=6G6=E@AC6G6?E
E96F?:E@C:ED4@?E6?ED7C@>72==:?8244:56?E2==J2?5DEC@?8
6?@F89E@DFAA@CEE96H6:89E@7E96F?:E2?54@?E6?ED
+96 %2E:@?2= *2?:E2E:@? @F?52E:@? %* C6BF:C6D E92E
F?:ED@G6C>>x:?H:5E9@CH6:89:?8>@C6E92?
 <8  =3D 6:E96C 36 D62=65 E@ @C C2:D65 23@G6 E96
:?DE2==2E:@?DFC7246 7F?:E42??@E36D62=652EE96A@:?E@7
FD6 >> x =68D 2C62G2:=23=6 E@ 2==@H 7@CAC@A6C
4=62?:?82446DD36=@HF?:E
+C2?DA@CEF?:E:?FAC:89EA@D:E:@?@?=J67@C6>@G:?8@C
E:AA:?8F?:ED64FC62==8=2DDDFC7246DH:E9E2A62?55C2:?
H2E6C7C@>H2E6CC6D6CG@:C2:=FC6E@5@D@>2JC6DF=E:?
52>286E@F?:E@CA6CD@?2=:?;FCJ
,D6@75:DE:==65H2E6C:?E96H2E6CC6D6CG@:C@79F>:5:7:65
F?:ED:DC64@>>6?565E@AC6D6CG6E96=:76@76=64EC:42=2?5
>6492?:42=4@>A@?6?ED 7?@?5:DE:==65H2E6C:DFD65E96
C6D6CG@:CH:==C6BF:C6A6C:@5:44=62?:?82?556=:>:?8C676C
E@E96$2:?E6?2?46D64E:@?7@C4=62?:?8AC@465FC6,?:E
72:=FC65F6E@=:>6@C>:?6C2=56A@D:ED:D?@E4@G6C65F?56C
H2CC2?EJ
@?@EFD656:@?:K65H2E6C6:@?:K65H2E6CH:==D9@CE6?
E96=:76@7E96H2E6CC6D6CG@:C2?5962E:?86=6>6?E
=62? F?:E 52:=J E@ 2G@:5 >2=7F?4E:@?D 2?5 >2:?E2:?
D2?:E2CJ@A6C2E:@?
,D6?@?23C2D:G64=62?6CD@?=J3C2D:G64=62?6CD4@F=5
D4C2E49E967:?:D9@7E96F?:E>2CC:?8:ED2AA62C2?462?5
>2<:?8:EDFD46AE:3=6E@D@:=244F>F=2E:@?
NOTICE
CAUTION
WARNING
#+) *&"1)
g '=F8F?:E:?E@2AC@A6C=J8C@F?5656=64EC:42=C646AE24=6
@7E964@CC64EG@=E286D:K62?5A=F84@?7:8FC2E:@? 7
A=F82?5C646AE24=65@?@E>2E494@?E24E2BF2=:7:65
6=64EC:4:2?E@56E6C>:?62?5:?DE2==E96AC@A6CG@=E286
2?5D:K66=64EC:42=C646AE24=6
g +FC?A@H6CDH:E49&F?A=F8A@H6C4@C52?52==@H
F?:E E@ 4@@= 367@C6 A6C7@C>:?8 2?J >2:?E6?2?46 @C
4=62?:?8
g &%&+DF3>6C86@CD2EFC2E6H:E9H2E6C,?:E:D?@E
H2E6CAC@@7@?@E@A6C2E6:7F?:E92D366?DF3>6C865
@CD2EFC2E65H:E9H2E6C
g ,?:E:D?@EH62E96CAC@@7#@42E6F?:E:?5@@CDH96C6
2>3:6?E2:CE6>A6C2EFC6:D2>:?:>F>@7ff
g @?@EDE62>4=62?@CFD66I46DD:G6H2E6C@?F?:E
g @?@EAF==F?:E3JA@H6C4@C5
g :D4@?E:?F6FD6:7A@H6C4@C5:D7C2J65@CH@C?
g @?@E2EE6>AEE@C6A2:C@CC6A=246252>2865A@H6C
4@C5 +96 4@C5 >FDE 36 C6A=2465 3J 2E4@ 2?
FE9@C:K65 2E4@ *6CG:46 86?E @C 2 A6CD@? H:E9
D:>:=2CBF2=:7:42E:@?D
g @?@E@G6C7:==H2E6CC6D6CG@:C&G6C7:==:?842?42FD6
6=64EC:42=D9@4<.2E6CC6D6CG@:C:D7F==H96?n#&&o
DE@AD7=2D9:?8@? %++$')+,)5:DA=2J
*E@A7:==:?8H96?n#&&oDE@AD7=2D9:?8@?5:DA=2J
g +FC?A@H6CDH:E49&2?52==@HF?:EE@4@@=367@C6
5C2:?:?8H2E6CC6D6CG@:C
g +9:DF?:E>FDE36D6CG:4653JBF2=:7:65A6CD@??6=@?=J
*6CG:463JF?BF2=:7:65A6CD@??6=>2J=625E@6=64EC:4
D9@4<@C3FC?
g ,D6 @?=J 6?F:?6 2E4@ )6A=246>6?E '2CED H96?
D6CG:46 :D C6BF:C65 2:=FC6 E@ FD6 6?F:?6 2E4@
)6A=246>6?E '2CED >2J DF3;64E @A6C2E@CD @7 E96
6BF:A>6?EE@92K2C5@FD6=64EC:42=G@=E286C6DF=E:?8:?
6=64EC:42=D9@4<@C3FC?6?F:?62E4@)6A=246>6?E
'2CED 2C6 DA64:7:65 E@ @A6C2E6 D276=J :? E96
6?G:C@?>6?ED :? H9:49 E96J 2C6 FD65 *@>6
27E6C>2C<6E@C86?6C:4C6A=246>6?EA2CED5@?@E92G6
E96492C24E6C:DE:4DE92EH:==2==@HE96>E@@A6C2E6D276=J
:?2E4@6BF:A>6?E
 )1)#@42E6F?:E2>:?:>F>@7>>x7C@>
4@>3FDE:3=6H2==D2?5>2E6C:2=D 7D2765:DE2?46D2C6?@E
>2:?E2:?655:D4@=@C2E:@?@C4@>3FDE:@?4@F=5@44FC
+967=F@C6D46?E=:89E7:IEFC6D:?E9:DF?:E92G6A=2DE:4D276EJ
D9:6=5D4@G6C:?8E967=F@C6D46?EEF36DE@>66E%2E:@?2=
*2?:E2E:@?@F?52E:@?%*DE2?52C5D+@2G@:5A6CD@?2=
:?;FCJ2?5@C7@@54@?E2>:?2E:@?2=H2JD@A6C2E6E96F?:E
H:E9E96A=2DE:4D276EJD9:6=5DAC@A6C=J:?DE2==65
+9:D F?:E 92D ?@ nFD6CD6CG:4623=6o A2CED 7 D6CG:46 :D
C6BF:C65@?E9:DF?:E4@?E24E2?FE9@C:K652E4@*6CG:46
86?E @C 4@?E24E E96 2E4@ *6CG:46 6A2CE>6?E 2E
 @C  72I  @C
?E6C?2E:@?2=72I
WARNING
)625E967@==@H:?8:>A@CE2?ED276EJ:?7@C>2E:@?367@C6FD:?8E9:D6BF:A>6?EE@2G@:5D6C:@FD:?;FCJ@C562E92?5
E@2G@:552>286E@6BF:A>6?E@CAC@A6CEJ
3
Form No. FSDC M-1010

$&#* %+ &%
Form No. FSDC M-1010
4
$&#*) '+ &%
==$@56=D
Flav-R-Savor®Humidified Holding and Display Cabinets come
in either brushed aluminum or painted Designer colors. All units
feature a digital temperature controller, air heating system,
fluorescent lamps, tempered glass side panels, and a tempered
glass door(s). Units can be configured with or without a
humidity system with low water control protection. The standard
access door can be hinged left or right. The cabinet interior top
and bottom is made of easy-to-clean stainless steel. All
available display racks are nickel-plated except the pretzel tree
display rack, which is stainless steel.
*2?5*+$@56=D
The FSD-1 is a standard single door model with a revolving
display motor. It has a revolving and stationary rack options that
hold three to five display trays.
The FSDT-1 is a single door model with a revolving display
motor like the FSD-1, but is 127 mm (5″) taller. It has revolving
and stationary rack options that hold three to seven display
trays.
On each model, the rotating rack stops automatically when the
door is opened. For details on different rack options, refer to
the OPTIONS AND ACC SSORI S section.
Figure 1. FSD-1 Model
N TE: Models FSD-1 and FSDT-1 cannot be converted to
models FSD-2/FSDT-2 or FSD-2X/FSDT-2X.
*2?5*+$@56=D
The FSD-2 and FSDT-2 are the same as models FSD-1 and
FSDT-1, but have an additional door on the opposite side of the
controls for pass-through convenience.
*/2?5*+/$@56=D
The FSD-1X is a single door model with a stationary rack that
holds five display trays.
The FSDT-1X is a single door model with a stationary rack like
FSD-1X, but is 127 mm (5″) taller. It has stationary rack options
that hold three to seven display trays.
For details on different rack options, refer to the OPTIONS AND
ACC SSORI S section.
Figure 2. FSDT-1X Model
N TE: Models FSD-1X and FSDT-1X cannot be converted to
models FSD-1/FSDT-1, FSD-2/FSDT-2, or FSD-
2X/FSDT-2X.
$@56=D*/2?5*+/
The FSD-2X and FSDT-2X are the same as models
FSD-1X and FSDT-1X, but have an additional door on the
opposite side of the controls for pass-through convenience.
N TE: Models FSD-2X and FSDT-2X cannot be converted to
models FSD-2/FSDT-2.
Figure 3. Model Designation
F S D T - 1 X
Flav-R-Savor
1 = One Door
2 = Two Doors
No Motorized
Rack Rotation
Display Cabinet
Tall

$@56= .:5E9

6AE9

6:89E

@@EAC:?E
.:5E9
@@EAC:?E
6AE9
FSD-1 569 mm
(22-1/2
''
)
612 mm
(24-1/8
''
)
699 mm
(27-9/16
''
)
518 mm
(20-3/8
''
)
518 mm
(20-3/8
''
)
FSD-1X 569 mm
(22-1/2
''
)
612 mm
(24-1/8
''
)
699 mm
(27-9/16
''
)
518 mm
(20-3/8
''
)
518 mm
(20-3/8
''
)
FSD-2 569 mm
(22-1/2
''
)
644 mm
(25-3/8
''
)
699 mm
(27-9/16
''
)
518 mm
(20-3/8
''
)
518 mm
(20-3/8
''
)
FSD-2X 569 mm
(22-1/2
''
)
644 mm
(25-3/8
''
)
699 mm
(27-9/16
''
)
518 mm
(20-3/8
''
)
518 mm
(20-3/8
''
)
FSDT-1 569 mm
(22-1/2
''
)
612 mm
(24-1/8
''
)
826 mm
(32-9/16
''
)
518 mm
(20-3/8
''
)
518 mm
(20-3/8
''
)
FSDT-1X 569 mm
(22-1/2
''
)
612 mm
(24-1/8
''
)
826 mm
(32-9/16
''
)
518 mm
(20-3/8
''
)
518 mm
(20-3/8
''
)
FSDT-2 569 mm
(22-1/2
''
)
644 mm
(25-3/8
''
)
826 mm
(32-9/16
''
)
518 mm
(20-3/8
''
)
518 mm
(20-3/8
''
)
FSDT-2X 569 mm
(22-1/2
''
)
644 mm
(25-3/8
''
)
826 mm
(32-9/16
''
)
518 mm
(20-3/8
''
)
518 mm
(20-3/8
''
)
*'  + &%*
Form No. FSDC M-1010 5
:>6?D:@?D
A B
C
Front View Side View
DE
Figure 4. Dimensions
Cabinet Openings:
FSD Models: 19″W x 18-5/8″H (483 x 473 mm)
FSDT Models: 19″W x 23-5/8″H (483 x 600 mm)
* Add 102 mm (4″) to the height of the unit if the 102 mm (4″) leg accessory is installed.
'=F8@?7:8FC2E:@?D
Units are supplied from the factory with an electrical cord and
plug installed. Plugs are supplied according to the applications.
#+)  *&" 1) '=F8 F?:E :?E@ 2 AC@A6C=J
8C@F?5656=64EC:42=C646AE24=6@7E964@CC64EG@=E286D:K6
2?5 A=F8 4@?7:8FC2E:@? 7 A=F8 2?5 C646AE24=6 5@ ?@E
>2E494@?E24E2 BF2=:7:65 6=64EC:4:2? E@ 56E6C>:?6 2?5
:?DE2==E96AC@A6CG@=E2862?5D:K66=64EC:42=C646AE24=6
N TE: The specification label is located on the ceiling sheet
inside the unit. See label for serial number and
verification of unit electrical information.
WARNING
Figure 5. Plug Configurations
N TE: Receptacle not supplied by Hatco.
CEE 7/7 Schuko BS-1363
NEMA 5-15P

$@56= -@=E286 6CEK .2EED >AD '=F8@?7:8FC2E:@? *9:AA:?8.6:89E
FSD-1 120 60 1440 12.0 N MA 5-15P 51 kg (113 lbs.)
and FSDT-1 220 50/60 1440 6.5 C 7/7 Schuko 51 kg (113 lbs.)
(with humidity) 240 50/60 1440 6.0 BS 1363 51 kg (113 lbs.)
220-230 (C ) 50/60 1440-1574 6.5-6.8 C 7/7 Schuko 51 kg (113 lbs.)
230-240 (C ) 50/60 1322-1440 5.8-6.0 BS 1363 51 kg (113 lbs.)
FSD-1 120 60 1115 9.3 N MA 5-15P 51 kg (113 lbs.)
and FSDT-1 220 50/60 1115 5.1 C 7/7 Schuko 51 kg (113 lbs.)
(no humidity) 240 50/60 1115 4.6 BS 1363 51 kg (113 lbs.)
220-230 (C ) 50/60 1115-1219 5.1-5.3 C 7/7 Schuko 51 kg (113 lbs.)
230-240 (C ) 50/60 1025-1115 4.5-4.6 BS 1363 51 kg (113 lbs.)
FSD-1X 120 60 1440 12.0 N MA 5-15P 50 kg (111 lbs.)
and FSDT-1X 220 50/60 1440 6.5 C 7/7 Schuko 50 kg (111 lbs.)
(with humidity) 240 50/60 1440 6.0 BS 1363 50 kg (111 lbs.)
220-230 (C ) 50/60 1440-1574 6.5-6.8 C 7/7 Schuko 50 kg (111 lbs.)
230-240 (C ) 50/60 1322-1440 5.8-6.0 BS 1363 50 kg (111 lbs.)
FSD-1X 120 60 1115 9.3 N MA 5-15P 50 kg (111 lbs.)
and FSDT-1X 220 50/60 1115 5.1 C 7/7 Schuko 50 kg (111 lbs.)
(no humidity) 240 50/60 1115 4.6 BS 1363 50 kg (111 lbs.)
220-230 (C ) 50/60 1115-1219 5.1-5.3 C 7/7 Schuko 50 kg (111 lbs.)
230-240 (C ) 50/60 1025-1115 4.5-4.6 BS 1363 50 kg (111 lbs.)
FSD-2 120 60 1440 12.0 N MA 5-15P 52 kg (114 lbs.)
and FSDT-2 220 50/60 1440 6.5 C 7/7 Schuko 52 kg (114 lbs.)
(with humidity) 240 50/60 1440 6.0 BS 1363 52 kg (114 lbs.)
220-230 (C ) 50/60 1440-1574 6.5-6.8 C 7/7 Schuko 52 kg (114 lbs.)
230-240 (C ) 50/60 1322-1440 5.8-6.0 BS 1363 52 kg (114 lbs.)
FSD-2 120 60 1115 9.3 N MA 5-15P 52 kg (114 lbs.)
and FSDT-2 220 50/60 1115 5.1 C 7/7 Schuko 52 kg (114 lbs.)
(no humidity) 240 50/60 1115 4.6 BS 1363 52 kg (114 lbs.)
220-230 (C ) 50/60 1115-1219 5.1-5.3 C 7/7 Schuko 52 kg (114 lbs.)
230-240 (C ) 50/60 1025-1115 4.5-4.6 BS 1363 52 kg (114 lbs.)
FSD-2X 120 60 1440 12.0 N MA 5-15P 51 kg (112 lbs.)
and FSDT-2X 220 50/60 1440 6.5 C 7/7 Schuko 51 kg (112 lbs.)
(with humidity) 240 50/60 1440 6.0 BS 1363 51 kg (112 lbs.)
220-230 (C ) 50/60 1440-1574 6.5-6.8 C 7/7 Schuko 51 kg (112 lbs.)
230-240 (C ) 50/60 1322-1440 5.8-6.0 BS 1363 51 kg (112 lbs.)
FSD-2X 120 60 1115 9.3 N MA 5-15P 51 kg (112 lbs.)
and FSDT-2X 220 50/60 1115 5.1 C 7/7 Schuko 51 kg (112 lbs.)
(no humidity) 240 50/60 1115 4.6 BS 1363 51 kg (112 lbs.)
220-230 (C ) 50/60 1115-1219 5.1-5.3 C 7/7 Schuko 51 kg (112 lbs.)
230-240 (C ) 50/60 1025-1115 4.5-4.6 BS 1363 51 kg (112 lbs.)
*'  + &%*
Form No. FSDC M-1010
6
=64EC:42=)2E:?892CEm *$@56=D
The shaded areas contain electrical information for ?E6C?2E:@?2=>@56=D@?=J
* Add 3 kg (7 lbs.) for the weight of FSDT models.
N TE: Shipping weight includes packaging.

%*+##+ &%
Form No. FSDC M-1010 7
• Glass Side Panels — The cabinets have tempered glass
side panels that are protected during shipping using
foam sheets along the glass edges and tape to hold the
panels securely. The sheets and tape must be removed
prior to cabinet operation.
N TE: Any impact to the tempered glass can cause breakage.
To remove a glass panel, grasp the panel firmly from
inside and outside of the cabinet. Lift up and out of the
bottom channel, then carefully lower the glass panel until
it clears the upper channel.
To reinstall, position the glass panel top edge under the
cabinet lip. Raise the panel until it clears the bottom
channel, then carefully lower the panel until it rests in the
bottom channel.
4. Place the unit in the desired location. Two people are
required for this step.
• Locate the unit in an area where the ambient air
temperature is constant and a minimum of 21° C
(70° F). Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods
and air conditioning ducts).
• Make sure the unit is at the proper counter height in an
area convenient for use.
• Make sure the countertop is level and strong enough to
support the weight of the unit and food product.
• Make sure all the feet on the bottom of the unit are
positioned securely on the countertop.
Figure 6. Components
Fill Cup
Access Door
Glass Side
Panel
Digital
Temperature
Controller
POWER ON/OFF
(I/0) switch
Display
Rack
Air Heating
System
6?6C2=
Flav-R-Savor®Humidified Holding and Display Cabinets are
shipped with most components installed and ready for
operation. The following installation instructions must be
performed before plugging in and operating the cabinet.
#+)  *&" 1) ,?:E :D ?@E H62E96CAC@@7
#@42E6F?:E:?5@@CDH96C6E962>3:6?E2:CE6>A6C2EFC6:D2
>:?:>F>@7ff
 )1)#@42E6F?:E2>:?:>F>@7>>x7C@>
4@>3FDE:3=6H2==D2?5>2E6C:2=D 7D2765:DE2?46D2C6?@E
>2:?E2:?655:D4@=@C2E:@?@C4@>3FDE:@?4@F=5@44FC
#@42E6F?:E2EE96AC@A6C4@F?E6C96:89E:?2?2C62E92E:D
4@?G6?:6?E7@CFD6+96=@42E:@?D9@F=536=6G6=E@AC6G6?E
E96F?:E@C:ED4@?E6?ED7C@>72==:?8244:56?E2==J2?5DEC@?8
6?@F89E@DFAA@CEE96H6:89E@7E96F?:E2?54@?E6?ED
+96%2E:@?2= *2?:E2E:@? @F?52E:@? %*C6BF:C6DE92E
F?:ED@G6C>>x:?H:5E9@CH6:89:?8>@C6E92?
 <8  =3D 6:E96C 36 D62=65 E@ @C C2:D65 23@G6 E96
:?DE2==2E:@?DFC7246 7F?:E42??@E36D62=652EE96A@:?E@7
FD6 >> x =68D 2C62G2:=23=6E@2==@H7@CAC@A6C
4=62?:?82446DD36=@HF?:E
+C2?DA@CEF?:E:?FAC:89EA@D:E:@?@?=J67@C6>@G:?8@C
E:AA:?8F?:ED64FC62==8=2DDDFC7246DH:E9E2A62?55C2:?
H2E6C7C@>H2E6CC6D6CG@:C2:=FC6E@5@D@>2JC6DF=E:?
52>286E@F?:E@CA6CD@?2=:?;FCJ
1. Remove the unit from the carton. Two people are required
for this step.
2. Remove the information packet.
3. Remove tape and protective packaging from all surfaces of
the unit.
• Floor Sheet — The stainless steel floor in all cabinets is
protected during shipping with a sheet of corrugated
cardboard. This protection must be removed prior to
cabinet operation.
• Display Rack — The display rack has packing material
and cardboard attached for protection during shipping.
This protection must be removed prior to cabinet
operation.
• Legs — The cabinets are shipped with four rubber feet
attached to the bottom of the unit. For cabinets with the
optional 4″ (102 mm) adjustable legs, see the OPTIONS
AND ACC SSORI S section for installation instructions.
N TE: If installing 102 mm (4″) legs, do not remove glass
protection until leg installation is complete.
CAUTION
WARNING

)6G6CD:?8E96446DD@@C
Flav-R-Savor Humidified Holding and Display Cabinet access
door(s) may be hinged on either the left or right side for
convenience. Use the following procedure to reverse the
access door.
N TE: For models equipped with a rotating rack motor (FSD-
1, FSDT-1, FSD-2, and FSDT-2), the “Relocating the
Proximity Switch” procedure in this section must be
performed after reversing the access door(s).
1. Remove the top hinge pin screw holding the door to the
hinge.
2. Tip the door assembly forward (away from cabinet) and lift
gently to clear the bottom hinge assembly. Remove the
nylon washer(s).
3. Reinstall the top hinge pin screw that was removed in step 1.
4. Remove the screws holding the hinges to the cabinet.
5. Remove the screws from the striker plates on the non-hinge
side of the cabinet.
6. Install the striker plates on the opposite side of the cabinet
where the hinges were previously mounted.
7. Install the hinges on the opposite side of the cabinet where
the striker plates were previously mounted using the original
hinge mounting screws.
8. Carefully rotate the door 180°.
9. Remove the hinge pin screw from the end that is now the
top.
10. Carefully place the door assembly with the nylon washer(s)
into the bottom hinge.
11. Tip/tilt the door assembly towards the cabinet and align the
door top with the hinge. Reinstall the top door hinge pin
screw through the hinged and into the door top.
Hinge Assembly
Bottom Hinge Pin Screw and
Nylon Washer(s)
Door Rotated 180°
Top Hinge
Pin Screw
Striker Plate and
Hardware
Figure 7. Reversing the Access Door
8Form No. FSDC M-1010
%*+##+ &%

%*+##+ &%
)6=@42E:?8E96'C@I:>:EJ*H:E49
)@E2E:?8)24<$@56=D&?=Jm**+
**+
Units equipped with a rotating rack motor will require relocating
the proximity switch(es) after reversing the door(s).
The proximity switch signals the rack motor to stop when a door
is opened and to start when the door is closed. Follow the steps
below to move the proximity switch(es) to the proper position
after reversing the door(s). Unit requires one switch per door.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Remove the four screws and top cover.
3. Remove the screw and nut securing the proximity switch to
the cabinet ceiling sheet. The screw is accessed from inside
the cabinet. Reinstall screw and nut into hole after removing
switch.
4. Cut the cable tie securing the proximity switch wires to the
wiring harness. Mark the two wires for reassembly and
unplug the wires from the proximity switch wire leads. Route
the wires to the opposite corner and reattach the wires to
the switch wire leads.
N TE: Make sure to install the proximity switch in the
orientation shown below for the specific installation
location. Incorrect orientation will result in malfunction of
the proximity switch.
5. Remove the screw and nut from the new mounting hole.
Secure the proximity switch to the mounting hole with the
screw and nut. Make sure to maintain proper switch
orientation when tightening the hardware.
6. Make sure wires do not interfere with the other components
inside the cabinet, then secure switch wires to wiring
harness with a cable tie (not supplied).
N TE: n models equipped with two doors, it may be
necessary to move the air chamber to access the
proximity switch on the customer-side door. Drain all
water from the unit, remove the drain plug from inside
the cabinet, and remove the four screws securing the
air chamber assembly to the cabinet. Carefully move
the air chamber out of the way to access the proximity
switch. Reassemble after relocating switch.
7. Install the top cover and four screws.
8. Plug the unit into the proper power source.
9. Turn on the unit and test the operation of the proximity
switch(es) by making sure the rack rotates when the doors
are closed and stops rotating when a door is opened.
Proximity Switch
Orientation with Door
Opening from Left
(Hinged Right)
Proximity Switch
Orientation with Door
Opening from Right
(Hinged Left)
Screw
Figure 8. Relocating the Proximity Switch
9
Form No. FSDC M-1010

6?6C2=
Use the following procedures to operate the Flav-R-Savor®
Humidified Holding and Display Cabinets.
)625 2== D276EJ >6DD286D :? E96 $'&)+%+ *+0
%&)$+ &% D64E:@?367@C6@A6C2E:?8E9:D6BF:A>6?E
*E2CEFA
1. Plug unit into a properly grounded electrical receptacle of
the correct voltage, size and plug configuration. See the
SP CIFICATIONS section for details.
2. Move the POW R ON/OFF (I/0) switch to the ON (I)
position.
• The display lights will turn on and the heating system will
start up.
• The CABIN T T MP RATUR display will flash “LO
H2O” four times and then flash the cabinet temperature.
It will continue to alternate this way until the water
reservoir is filled. Once the reservoir is full, “LO H2O” will
stop flashing and the display will show the cabinet
temperature.
Figure 9. Setting the Humidity Level
,D6@75:DE:==65H2E6C:?E96H2E6CC6D6CG@:C@79F>:5:7:65
F?:ED:DC64@>>6?565E@AC6D6CG6E96=:76@76=64EC:42=2?5
>6492?:42=4@>A@?6?ED 7?@?5:DE:==65H2E6C:DFD65E96
C6D6CG@:CH:==C6BF:C6A6C:@5:44=62?:?82?556=:>:?8C676C
E@ E96 $ %+%% D64E:@? 7@C 4=62?:?8 AC@465FC6
,?:E72:=FC65F6E@=:>6@C>:?6C2=56A@D:ED:D?@E4@G6C65
F?56CH2CC2?EJ
@?@EFD656:@?:K65H2E6C6:@?:K65H2E6CH:==D9@CE6?
E96=:76@7E96H2E6CC6D6CG@:C2?5962E:?86=6>6?E
N TE: Unit failure caused by deionized water is not covered by
warranty.
3. Fill the water reservoir with clean
water. To fill the reservoir:
a. Lift up the WAT R FILL cup cover
and pull forward.
b. Slowly pour water into the cup until
“LO H2O” stops flashing on the
cabinet temperature display.
NOTICE
WARNING
Fill Cup
*IMPORTANT NOTE*
When using distilled water, add one teaspoon of salt to the
water reservoir during the initial water fill only. This will ensure
proper operation of the water level sensors.
#+) *&"1)@?@E@G6C7:==H2E6CC6D6CG@:C
&G6C7:==:?842?42FD66=64EC:42=D9@4<.2E6CC6D6CG@:C:D7F==
H96?n#&&oDE@AD7=2D9:?8@? %++$')+,)
5:DA=2J *E@A 7:==:?8 H96? n#& &o DE@AD 7=2D9:?8 @?
5:DA=2J
N TE: The capacity of the water reservoir is 2.8 L (3/4 gallon).
n the initial fill, the water reservoir may take up to
3.8 L (1 gallon) of water.
4. Set the humidity to the desired level (refer to the “Setting
the Humidity Level” procedure in this section). See the
“Food Holding Guide” for recommendations.
5. Set the air temperature to the desired temperature (refer to
the “Setting the Air Temperature” procedure in this section).
See the “Food Holding Guide” for recommendations.
6. Allow the unit 30 minutes to reach operating temperature
before loading the cabinet with pre-heated food product.
$2<6DFC67@@5AC@5F4E92D366? 962E65E@E96AC@A6C
7@@5D276E6>A6C2EFC6 367@C6 A=24:?8 :? F?:E 2:=FC6 E@
962E7@@5AC@5F4EAC@A6C=J>2JC6DF=E:?D6C:@FD962=E9
C:D<D+9:DF?:E:D7@C9@=5:?8AC6962E657@@5AC@5F4E@?=J
,)%1)*@>66IE6C:@CDFC7246D@?E96F?:EH:==86E
9@E,D642FE:@?H96?E@F49:?8E96D62C62D
*6EE:?8E96:C+6>A6C2EFC6
1. Press the key to enter temperature mode (“tSP” will
appear on the CABIN T T MP RATUR display).
2. Press the key again to show the current temperature
setting.
3. Press the key or key to reach the desired
temperature. The temperature range is 27°–91°C
(80°–195°F) in single degree increments. See the “Food
Holding Guide” in this section for recommendations.
4. After the desired temperature is set, wait 15 seconds
without pushing any keys for the cabinet temperature
display to return automatically to operational mode.
*6EE:?8E96F>:5:EJ#6G6=
1. Press the key to enter humidity mode (“hSP” will
appear on the CABIN T T MP RATUR display).
2. Press the key again to show the current humidity level.
3. Press the key or key to reach the desired humidity
level. Humidity range is 1 through 5 (1 is the lowest amount
of humidity and 5 is the highest). See the “Food Holding
Guide” in this section for recommendations.
4. After the desired humidity level is set, wait 15 seconds
without pushing any keys for the cabinet temperature
display to return automatically to operational mode.
WARNING
WARNING
10 Form No. FSDC M-1010
&')+ &%