hattrick I-CONCEPT User manual

- 1 -
I-CONCEPT TREADMILL USER MANUAL

- 2 -
INDEX
1. OUTLOOK INSTRUCTION ..............................................................................................................3
2. SAFETY INSTRUCTION...................................................................................................................4
3. GROUNDING WIRES INSTRUCTION ..............................................................................................5
4. ASSEMBLE PART LIST ....................................................................................................................6
5. ASSEMBLE STEPS ..........................................................................................................................7
6. CAUTION ....................................................................................................................................10
7. MAINTENANCE...........................................................................................................................11
8. COMPUTER OPERATION INSTRUCTION......................................................................................12

- 3 -
1. OUTLOOK INSTRUCTION
電子表
電源開關
電源線
過載保護開關
底座
修飾蓋
安全插銷/夾子
電源線
機台主架
后調整盒
Computer
Power switch
Power cord
Circuit breaker
Safety clip
Power wire
Frame
Base
Rear end cap
Decorative cover

- 4 -
2. SAFETY INSTRUCTION
When using this product, basic precautions should always be followed, including the
following:
Please read the instruction carefully before starting to use this product.
DANGER –To reduce the risk of electric shock：
1. Always unplug this product from the electrical outlet immediately after using and before
cleaning.
WARNING –To reduce the risk of burns, fire, electric shock, or physical injury：
1. The product should never be left unattended while plugged in. Unplug the product from the
outlet when not in use.
2. Close supervision is necessary when this product is used by or near children, invalids, or
disabled persons.
3. Be sure to use the product only for its intended use as described in this manual. Do not use
any attachment not recommended by the manufacturer in order to avoid any danger or
accidents.
4. Never operate the product if it has a damaged cord or plug, if it is not working properly, if it
has been damaged, or dropped into water. Please return the product to the service center of
seller for examination and repair.
5. Do not carry this product by the supply cord or use the cord as a handle.
6. Keep the cord away from hot surfaces or ground.
7. Never operate the product with the air vents blocked. Keep the air vents free of lint, hair, etc.
8. Never drop or insert any objects into any openings.
9. Do not use or operate outdoors.
10. Do not operate where aerosol (spray) products are being used or where oxygen is thin.
11. Before turning the product power off, turn all controls to the off position then remove the
plug from the outlet.

- 5 -
12. Connect the product to a properly grounded outlet only.
13. If the power cord is damaged, be sure to ask the manufacturer for replacement to avoid
accidents. The seller and correlative qualified professionals are as well as eligible.
3. GROUNDING WIRES INSTRUCTION
The products must be grounded first. If malfunction or breakdown occurs, grounding will provide a
path of least resistance for electric current to reduce the risk of electric shock.
The product is equipped with a cord having an equipment-grounding conductor and a grounding
plug.
The plug must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
DANGER –Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether
the products are properly grounded. Do not modify the plug provided with the product –if it will
not fit the outlet, have a proper outlet install by a qualified electrician.
The product is for use on nominal 220V-240V and has a grounding plug that looks like the plug
illustrated in the figure. Make sure that the product is connected to an outlet having the same
configuration as the plug.
There is no need to use any adapter for this product.
Grounding methods
GROUNDED
OUTLET
GROUNDING END

6
4. ASSEMBLE PART LIST
abce
dfghi
A
B
C
D
E
j
ITEM
DESCRIPTION
Q'TY
ITEM
DESCRIPTION
Q'TY
A
Frame
1
a
Nylon nut M6×P1.0
4
B
Computer console set
1
b
Truss hex screw M8xP1.25x40
4
C
Decorative cover left
1
c
Truss hex screw M8xP1.25x90
2
D
Decorative cover right
1
d
Safety key set
1
E
I-PAD Sucker
2
e
Truss Philips screw M5xP0.8x15
6
F
f
Wrench
1
G
g
Hex wrench+screwdriver 5mm
(70mmX70mm)
1
H
h
L-hex wrench
1
I
i
SLILCON
1
J
j
Washer Ø16xØ6x1.0t
4

7
5. ASSEMBLE STEPS
WARNING:
After assembly the treadmill, then you
can untie the loincloth.
A
© T© w§ô±a
Two persons are required to finish the
assembly steps.
Caution: Please follow exactly the
assembly steps below to avoid injury.
1. Put up the handrail tubes of Frame(A)
as the arrow shows in the right
drawing and tighten with Hex
Screw(b).
Ps. To avoid unexpected accident,
always assemble the treadmill with
more than two workers, do not
assemble by yourself.
b
b
Loincloth

8
2. Put up Upright (L&R) as shown in
the right drawing and tighten with
Hex Screw(b),(c).
Ps. To avoid unexpected accident,
always assemble the treadmill with
more than two workers, do not
assemble by yourself.
b
b
c
c
3. After finished the above steps and
you can untie the loincloth, then
wedge decorative cover(C,D) into
the frame respectively as shown in
the right drawing and tighten with
Philips screw(e).
e
e
C
D

9
4. Connect the middle control wire with
the upper control wire, then put the
computer set as right image and
tighten with nylon nut (a) and
washer(j)
a
B
j
5. When you need to use the IPAD,
Please paste the suction cups for
suitable place on the computer,
then you can put your IPAD on the
holder and sucked with suction cups
to avoid the IPAD falling out
§l½ L I-PAD
Sucker

10
6. CAUTION
This treadmill has the foldable mechanism for
storage. Stop all the movements (including stop the
running belt and take off the power cord) before
storage, then pull out the POP-Pin of the folding
fixing mechanism as the direction shown in the
drawing and then lift up the frame until the
POP-Pin inserts into the frame. When doing this
action, two persons are needed. One puts up the
frame and another pulls out the POP-Pin of the
folding fixing mechanism. On the contrary, if you
want to use the treadmill, pull out the POP-Pin of
the folding mechanism as the arrow shows in the
drawing and put down the frame slowly
Ps.1.To prevent from danger, be careful if the kids
are around.
Ps.2. If you want to move the treadmill, fold the
treadmill at first, hold the rear adjust cap with your
hands, then lean the treadmill and do not move
the treadmill until the roller can be moved
smoothly.
Ps.3. To avoid the injury, do not move the treadmill
on uneven ground.

11
Note: The Cylinder contains high pressure
gas. Please avoid crash with other objects to
avoid danger.
Note: If the Cylinder is hit, it might be
damaged and cause the usage not smooth.
The treadmill might fall while folding
7. MAINTENANCE
1. If the belt tends to move off the center, stop
the treadmill. Take the Hex Wrench and adjust the
Hex Screw in the Rear End Cap. For example, if the
running belt is moving towards the left side,
tighten the left Hex Screw about 1/4
turn(clockwise); if the running belt is moving
towards the right side, tighten the right Hex Screw
about 1/4 turn(clockwise); Turn on the treadmill
after it has been adjusted. If you find that the belt
has not moved to the proper position, please
repeat the steps above. Don’t use the treadmill
until the running belt returns to the center
position.
(Ps.1. This action is very important, if the belt is not
in the center, be sure to follow above steps.)
(Ps.2. The position of running belt might not stay
precisely in the center with slightly towards the
left and right sides, and the situation varies
with how end-users use and the weight of
end-users. No need to adjust the belt if it
doesn’t rub against the parts aside.)

12
2. Depending on the usage of the product, please
apply SILICON on the board according to the below
chart. Use the Hex Wrench to unscrew the bolt
inside the Rear Roller. Then pull the belt up and
daub some SILICON to the center of the board.
After that, adjust the belt to the center of the deck,
followed by tightening the screw to the original
set.
(Ps. When the belt is sliding, please follow the
above method to lubricate the running board. )
Use Situation（Speed)
Time
1~6 km/h
1Years
6~12 km/h
6 Months
12km/h above
3 Months
8. COMPUTER OPERATION INSTRUCTIONS
I. Start Display:
1. If the SAFETY key is taken out, the matrix window will display a down arrow. If the SAFETY key
is replaced, the matrix window will display KGS (LBS) for avoirdupois unit; the weight window
glitters and displays the pre-set value. The value is 70KG (150LBS) and range 23~130KG
(50~286LBS). At this time the light of Weight window shines. Finish setting or not setting,
press the ENTER key and the window will turn to start / ready status. The matrix window
displays a pulsatile heart-shaped picture. The aim of setting the weight is to change burning

13
CALORIES. This can be done only after starting. It does not need to be set in PROGRAM. It
means you can use the value after starting. You must set it anew after restarting
2. If the SAFETY key is removed out during the work, then the treadmill will stop running. At this
time, place the SAFETY key back, the beeper will sound and all the values will go back to the
initial position.
3. Under the common Start / Ready status, the PULSE window will display the HP picture if you
don’t grip the pulse sensor. If you grip the pulse sensor, you will see PULSE window starting to
display the pulse value.
4.
II. Operation Instruction
1. Under the Start/Ready position, you can press the MODE key directly to enter the edit
program.
2. Under the Start/Ready position, press the QUICK START key to directly enter the start-up of
Manu run.
3. When the SAFETY key is taken off and then replaced, it will not initiate a make reposition action
anywhere it is. You need to press the QUICK START key to perform the incline to reposition it.
4. When the power is on, it will not make any reposition action anywhere it is. You need to press the
QUICK START key to perform the incline to reposition it.
5. Under the start/ready status, continuously press the stop STOP key for 5 seconds; it will initiate

14
the make reposition action anywhere it is.
While performing any program, if you press the STOP key, the program will stop. If users want to
continuously perform the program, press the QUICK START key or press the STOP key again to
leave the program and return to the start/ready status
III. Edit Mode：
1. Under the Start/Ready position, press the MODE key to edit mode ,pressing SPEED + or - key
to choose, speed display P1→P2→P3→P4→P5→P6→P7→M→H。
2. Six angular matrix windows default display "G" (Gaol), shows M representation Custom, shows
the H representation (HRC)
3. After time setting, press ENTER key，enter into second level setting item”LEVEL” ，value
display on INCLINE window，preset value” 1”，range 1~6 ，STEP is 1，after trun on treadmill，
matrix window display range of 1~30”INCLINE”of LEVEL from left to right
4. After edit, you can press ENTER key start or press QUICK START key start. During edit,if press
QUICK START key start directly ,then other no edit parts will take preset value directly.
5. PPROGRAM has 30 levels in all. The three anterior are WARM UP, the three latter are COOL
DOWN. Each is 3 min. The setting time, except for anterior and latter which mean 6 min, will
be executed on average by the surplus 24 levels
6. 9 HOLES mode has no functions of WARM UP or COOL DOWN. When the distance is equal to
3.5KM, the motor will stop, the INCLINE is 0 and it displays “End”.
IV. Program Operation and Instruction：
1. When you press the QUICK START key, it will begin to count down for 3 sec; after that, the
motor will start, the speed will start at 1.0KPH.
2. Speed STEP is 0.1; you can press SPEED + or - key to select, long press key speed of +/-will
change quickly, or press speed instant key 1、4、7、10 to select.

15
3. Incline step is 1, you can press INCLINE +or - key to select, long press key incline of +/-will
change quickly ,or press incline instant key 1、4、7、10 to select.
4. During motor working, press Stop key，the motor and incline motor are stop, time window
display ”PAUSE”；If press QUICK START key again, then count backwards 3 seconds，motor will
start again, speed value will keep in the front of stop, incline will rose to the height in the front
of stop.
5. On PAUSE state, hold on the Stop button for 3 seconds, jump back to the standby screen
6. If the time is over(zero), the END, after 30 seconds of the END state, will automatically jump
back to the standby screen too.
V. Program Mode
Press Mode or SPEED + / SPEED - key to switch program-controlled, program-controlled switching
sequence is as follows:
P1 →P2 →P3 →P4 →P5 →P6 →P7 →Custom→H.R.C. (LOOP)
Press the STOP Key to return to the upper menu
PROGRAM
P1 Goal
1 Press ENTER to confirm the selection Manual, ENTER the TIME setting:
Press SPEED + or SPEED - adjusting target time, initial values is 0:00, range of 0, 20:00 ~ 99:00, the
unit is minutes: seconds
2. Press ENTER to confirm set time, enter into the Distance setting:
Press SPEED + or SPEED - adjusting target distance, the initial value is 0.00, the range of 0,1.00-99.00,

16
the unit is km (mile)
3. Press ENTER to confirm the setting distance, enter into the Calories setting:
Press SPEED + or SPEED - adjusting target calories, the initial value is 0, the range of 0, 10-999 units
for calories
4. After any item set is complete, press START button to begin the training, the program will set value
as the target, when the target is zero run end.
Note: Time, Distance, Calories can be set in a loop, when one set value, the value of the two rest
automatic reset
Note: the Time, Distance, Calories set to zero, the numerical do positive action after start-up
P2 9 hole LEVEL：input1，range of 1~6，step1，And in 3500 meters distance calculation.
P3 hill climb LEVEL：input 1,range of 1~6，step 1.
time：preset 30min；range of 20~99min，step 1 min.
P4 hill run LEVEL：input 1,range 1~6，step 1.
time：preset 30min，range of 20~99min，step 1 min.
P5 interval LEVEL：input 1，range of 1~6，step 1.
time：preset 30min，range of20~99min，step 1 min.
P6 rolling LEVEL：input 1，range of 1~6，step1.
time：preset 30min，range of 20~99min，step 1 min.
P7 Weight loss LEVEL：input 1，range of 1~6，step 1.
time：preset 30min，range of 20~99min，step 1 min.
Custom1 Each group total has 30 level can be set, hexagonal matrices window shows M,
speed and the ascension of the default values are the lowest numerical value，adjustment of the
values displayed in SPEED Windows and INCLINE Windows respectively, After adjust, press the
ENTER key will jump to TIME 2, and so on, long press the ENTER key for 5 seconds, then stored value,
to leave edit mode, and switch to the TIME set, preset 30 min, the range of 20 ~ 99 min, step 1 min.
HRC (THR)
i. Hexagonal matrix window shows A (show age), press ENTER key or wait 5 seconds or press
the SPEED + / - keys displayed automatically preset: 30,press SPEED key + / - keys to adjust the
age, the age range of values: 13-80, Step 1 set. After completely, press the ENTER key, into the
next option
ii. PULSE flash of PULSE Windows at this time, display the default values of the age, press
SPEED + / - key to input the heart value, this value will be changed along with the different
age, but not more than set the scope of upper and lower limit, please refer to below schedule

17
and choose a suitable value for yourself. if you didn't do any change, press the ENTER key, the
program will start running in accordance with the default values, and into the next option.
iii. At this time ,TIME Windows start flashing, the program will ask you to input the time value,
you can press SPEED + / - keys to set the time you need, or press the QUICK START key directly,
using the way of no countdown start motion. time value range: 5-99 min, default values for
20 min, step 1.
** The following is age and heart of the treadmill HRC function value (default) table:
1.1. A
ge
BPM
Age
BPM
Age
BPM
Age
BPM
H
Pre-set
L
H
Pre-set
L
H
Pre-set
L
H
Pre-set
L
13
197
124
124
31
180
113
113
49
162
103
103
67
145
92
92
14
196
124
124
32
179
113
113
50
162
102
102
68
144
91
91
15
195
123
123
33
178
112
112
51
161
101
101
69
143
91
91
16
194
122
122
34
177
112
112
52
160
101
101
70
143
90
90
17
193
122
122
35
176
111
111
53
159
100
100
71
142
90
89
18
192
121
121
36
175
110
110
54
158
100
100
72
141
90
89
19
191
121
121
37
174
110
110
55
157
99
99
73
140
90
88
20
190
120
120
38
173
109
109
56
156
98
98
74
139
90
88
21
189
119
119
39
172
109
109
57
155
98
98
75
138
90
87
22
188
119
119
40
171
108
108
58
154
97
97
76
137
90
86
23
187
118
118
41
170
107
107
59
153
97
97
77
136
90
86
24
186
118
118
42
169
107
107
60
152
96
96
78
135
90
85
25
185
117
117
43
168
106
106
61
151
95
95
79
134
90
85
26
184
116
116
44
167
106
106
62
150
95
95
80
133
90
84
27
183
116
116
45
166
105
105
63
149
94
94
28
182
115
115
46
165
104
104
64
148
94
94
29
181
115
115
47
164
104
104
65
147
93
93
30
181
114
114
48
163
103
103
66
146
92
92

18
BTM (Bluetooth module) APP for iPad
1APP software download
Please connection the iPad to App(iTunes) Store, Search pafers, and then review the introduction of
APP, download the APP to the iPad which the have treadmill’function, such as "Tread Montior" and
"Run On Earth".
APP will using Bluetooth mode connection with treadmill, so please confirm the treadmill
has add Bluetooth
APP contains the following functions, the user must open 3G network or Wi-Fi network, can
be use normal:
(a) Sports Management: After the register and login into the personal account, you can record or
review the cumulative value for the each motion..
(b) Some APP need connection to the Google map to do the operation’s display after the locate.
2Operations for treadmill execute APP:
STEP.1 Let the Bluetooth device pairing with the iPad 將Bluetooth
(a) Please put the Ipad to the ipad holder which in front of the LCD then can fixed the iPad
(b) Enter the set the project of the iPad, open the Bluetooth device detection.
(c) iPad will detection all of the Bluetooth device that under the detection range .select the
treadmill’s Bluetooth device name to do pairing, the confirmation screen will display
"connected", and check the upper right corner of the iPad whether show the
patterns (white flag, said Bluetooth pairing success; gray, is said to have been started but not
matched yet)

19
(d) After Bluetooth connection success about 10 seconds, the LCD screen will become to white
and the lower right corner of the pattern change from to , it mean is the
computer connection with iPAD is successful also.
After pairing success, please perform the treadmill APP in 2 minutes, if more than 2 minutes
is not executed, or the distance of iPad with treadmill running is move than 2 meters, the
Bluetooth will automatically cancel the connection "Not connected", please follow above
steps again.
STEP.2 Press the iPad main menu button , the screen will be return to iPad desktop.
STEP.3 Start the iPad treadmill APP of downloaded, enter to APP page, treadmill will detect APP,
when the APP and treadmill connection success, then unlock APP screen, can start from APP interface
to use various modes to control the treadmill.
APP instructions, precautions and function introduction, please visit the APP download page
to review the description or contact the Pafers/ dealer ask for instructions.

20
STEP.4 After use APP for each time, please press the main key (HOME) 2 times on "iPad" to close the
APP.
3I f APP in abnormal or meet any Bluetooth connection problems in use time, please follow the
below steps to restore the connection:
STEP.1 Quick press the main key "(HOME)"of 2 times on “iPad to clear the APP cache.
STEP.2 About 3~5 seconds will hear "beep" sound, please turn off the power of treadmill .
STEP.3 Tturn on the power, back to the iPad set project, press ”→” key what right of the
Bluetooth device name, let the Bluetooth device name to do "forget".
STEP.4 iPad will re-search the Bluetooth device, please do the re –pairing
STEP.5 When the pairing is successful, return to the iPad desktop to re-execute APP.
If it still abnormal, Please check the Bluetooth device with iPad matching whether belong this
treadmill, if it is correct, please turn off the iPad, maybe the iPad crash or meet the wireless
interference
4For below situation, may can make iPad automatically disconnected:
When using APP, synchronization using application of background, such as listen to music or review
the photos... And so on, please try to reduce the round-trip times or open too many applications,
due to the iPad will disconnect in sometime because of resource and self-protection.
If happen the connection disconnected, treadmill will start the protection function, make
continuous warning beep sound, then automatically turn off the speed of the treadmill, so as
not to cause the safety problem for the user
Support equipment (the following is a list, please refer to the APP download page.)
iPod touch (The fourth)
iPod touch (The Third)
iPhone 5
iPhone 4S
iPhone 4
Mini iPad
iPad 2
iPad