hattrick TRENDY M User manual

0
TRENDY M MOTORIZED TREADMILL USER MANUAL
Special tips：
Before installation and operation, please read this operation manual carefully and save this
manual for future reference.

Table of Contents
CONTENT
PAGE
1、Warranty
1
2、Tips for Safety
2
3、Packing Details
3
4、Explosive View
4
5、Part List
5
6、Treadmill Structure
6
7、Installation
7
8、Use Instructions
9
9、Guides for Console Operation
10
10、Detailed Instructions
13
11、Maintenance
15
12、Guides for Malfunction
17

- 1 -
Acknowledgement
Thank you for purchasing this item which can improve your health.
1、Warranty
We make sure that this item is made of high-quality materials.
In normal use, we will take charge of maintenance if any problem occurs.
If the item you purchased meets problems as follows, the manufacturer’s
warranty is not effective:
Damage caused by external reasons
Don’t use original manufacturer’s spare parts
Improper handling by yourself
Operate against user manual
For easy-wear parts, such as belt, we don’t provide maintenance and
replacement for normal use.
This warranty is only valid for home use, but is not suitable for gym or other
professional exercise.
If you want to purchase spare parts, please contact our services and provide this
manual.
2、Tips for Safety
We take much concern on safety when we are designing and producing this item.
However, in case of emergency, please pay attention to following tips. We don’t
assume responsibility if any accident caused by improper operation..
According to your body condition, please exercise properly. Overload or
improper exercise will damage your health.
While running, you should dress properly. Don’t dress too loosely in case your
clothes will be entangled by the machine .And please wear sport shoes. In order
to avoid unnecessary injury, please don’t let your children or pets play near the
machine.
This item is not suitable for children. For patients or the disabled, please use the
machine under the guides of their doctors or guardians.
Don’t use this machine outdoor, high-humidity condition or in the sun.
Please power off and pull the plug when the machine is not in use.
This machine is for home use, but not suitable for professional exercise or testing
and medical purposes.
The displayed heart rate is for reference, not for medical use.
If power wire is broken, please ask the manufacturer or professional services to
replace it in case of danger.
Please check all the parts before use. Make sure that all the screws and nuts are

- 2 -
fastened.
Please place the item on the clean, flat and solid floor. Make sure there is
nothing sharp, no source of water or hear around the machine.
Please stop exercising immediately and consult your doctor or fitness coach if
you’re feel giddy, surfeit, thorax ache or other symptoms.
Hands shall avoid all running parts. Don’t put your hands or feet under the
running belt.
This item is only for one person to use!
Please use original manufacturer’s spare parts and don’t replace them yourself.
3、Packing Details
Warning: Carefully install the product, avoid making any damage.
Notice: 1) Carefully read instructions before installation, operate in accordance with
procedures.
2) Remove all paper boxes and foams
3) Check all the following components. If there are missing or problematic
parts, please contact our services.
Frame
Meter
Meter pillar
Decorative
cover
Hardware bag
Multifunction
frame
Massage head
Horizontal pipe
Sponge sheath for
feet

- 3 -
Hardware bag
Multi-wrench 1 pcs
Homemade wrench 1 pcs
Umbrella-type allen screw
M8*80 1pcs
Umbrella-type allen screw
M8*50 4pcs
Umbrella-type allen screw
M8*35 2pcs
Umbrella-type allen screw
M8*15 12pcs
Umbrella-type cross tapping
screw M4.2*15 4pcs
Nut 7pcs
Washer 19pcs
Safety key 1pcs
MP3 connector 1pcs
Lubricant 1pcs

- 4 -
4、Explosive View：
These are all the components used in installation. All components are listed in the
following form.

- 5 -
5、Part List
No.
Description
Quantity
No.
Description
Quantity
1
Base frame
1
30
Rubber transporting wheel
2
2
Main frame
1
31
Tube plug at base frame
2
3
Left meter pillar
1
32
Upper cover of meter
1
4
Right meter pillar
1
33
Under cover of meter
1
5
Meter frame
1
34
Sponge sheath on handbars
2
6
Motor stator
1
35
Hand heart rate&speed buttons
1
7
Connecting part of base frame
1
36
Hand heartrate& incline buttons
1
8
Motor
1
37
Safety key
1
9
Under control panel
1
38
Speaker
2
10
Front roller
1
39
Upper control panel
1
11
Back roller Motor
1
40
Key board
1
12
Pressure stick
1
41
MP3 module
1
13
Multislot belt
1
42
Upper communication line
1
14
Power switch
1
43
Under communication line
1
15
Overload protector
1
44
Green connecting line
1
16
Running belt
1
45
Red connecting line
1
17
Running board
1
46
Power wire
1
18
Motor cover
1
47
Red connecting line
1
19
Footplate
2
48
Speed sensor wire
1
20
Left back cover
1
49
Reed pipe for safety key
1
21
Right back cover
1
50
Locating pad of footplate
8
22
Cover of transporting wheel
2
51
Manual incline
2
23
Transporting wheel
2
52
Multifunction frame
1
24
Adjustable foot pad
4
53
Sponge sheath for feet
4
25
Left decorative cover
1
54
Tube plug
4
26
Right decorative cover
1
55
Massage head
1
27
Cover under motor
1
56
Horizontal pipe
1
28
Shock absorber
4
29
Shock gasket
1

- 6 -
6、Treadmill Structure
Meter
Keys on the handlebar
Handlebar
Meter pillar
Motor cover
Footplate
Running belt
Base frame
Decorating cover
Back cover
Safety key
Multifunction frame
Massage
head
Manual incline

- 7 -
7、Installation
Step 1: Install meter pillars
a) Let the communication line pass through the right meter pillar.
b) Put meter pillars on the base frame. First, use 2 Screw M8*15 and 2 washers;
second, use 4 Screw M8*50, 4 washers and 4 nuts to fasten meter pillars. (Don’t
tighten screws at first )
Step 2: Install the meter
a) Make sure that communication lines are connected correctly
b) Put the meter on the meter pillars. Use 6 Screw M8*15 and 6 washers to fasten
the meter. (Don’t tighten screws at first)
c) Turn power on and start the machine. If all functions work well, tighten all
screws in Step 1 and 2.
Screw M8x15
Washer
Screw M8x15
Washer
Communication line
Nut
Screw M8x50

- 8 -
Step 3: Install horizontal pipe
a) Put horizontal pipe to pillars, then use 4 Screw M8x15 and 4 washers to fasten
the pipe. (Don’t tighten screws at first)
Step 4: Install multifunction frame
a) Use 2 Screw M8x35, 2 washers and 2 nuts to fasten multifunction frame to base
frame. (Don’t tighten screws at first)
b) Use 1 Screw M8x80, 1 washer and 1 nut to fasten multifunction frame to
horizontal pipe. Then tighten all screws in Step 3 and 4.
Screw M8x15
Washer
Screw M8x80
Washer
Nut
Screw M8x35

- 9 -
Step 5: Install the massage head
a) Use 3 Screw M8*15 to fasten the massage head.
Step 6: Install decorative covers.
a) Use 4 Screw M4.2*15 to fasten left and right decorative covers.
Step 7: Remove the screw in base frame.
Screw M4.2*15
Remove the screw
Screw M8*15
Washer

- 10 -
8、Use Instructions
Power:
Insert the power plug and switch on the machine. The switch light will be on and you
will hear a sound like “Di”. Then you will find the meter is on.
Safety key：
The machine can work only when safety key is put at the appointed position. Nip the
other end of safety key to clothes. In this way, you can pull up safe key to stop the
machine immediately in case of accidents. If you want to use the machine again, put
safety key back.
Folding instructions：
Folding：
Folding the machine will save space.
Before folding, please switch off and pull up the plug.
Use hands to lift the running board until it is locked.
Unfolding：
First, lift up the running board a little and step on the pressure sticker. Second pull
down the running board for a while, then the running board will goes down to the
ground automatically.
Manual incline operations:
This item is with manual incline, and there are three different grades: 1%, 2% and
3%. If you would like to change incline, please do as follows:
Power switch

- 11 -
1. Stop the machine and pull two metal sticks from left and right manual incline.
2. Put two metal sticks into the relatively same hole of left and right manual incline
3. After that, adjust two metal sticks to touch the base frame
4. Before starting the machine, check Step 2 and 3 again.

- 12 -
9、Guides for Console Operation
Specifications
Time
00:00-99:59 min
Speed
1.0-16.0 km/h
Distance
0.00-99.9 km
Calories
0-999 kcal
Heart rate
50-200 / min
Program
Built-in program
P1-P99
Count-down mode
Time/Distance/Calories
User-defined program
U1—U3
Body fat
measurement
Fat
Sex
1/0 (Man/Woman)

- 13 -
Panel buttons and functions
START button:
Press “Start” button, the system will count down
in 3 seconds, which displays on the screen! The
machine will run at the speed of 1.0km/h.
STOP button:
Press this button to stop the running machine.
Reset:
Press “Stop” button twice continuously to reset
the machine.
PROG. button
In ready condition, press “PROG” button to select
programs from P1-P99, U1-U3 and FAT.
P1-P99 are built-in programs. U1-U3 are user-
defined programs. FAT is body-fit program.
After finish selection, press “Start” button to
start the machine!
MODE button
In ready condition, press “MODE” button to select
from Time, Distance and Calories count-down
modes.
After finish selection, press “Start” button to
start the machine!
SPEED △▽button
In ready condition, buttons are used to adjust
preset-data.
In running condition, buttons are used to adjust
speed, and the adjusting range is 0.1km/h each
time. Keep pressing buttons for over 0.5 second,
the speed will continuously increase or decrease.
SPEED direct button
In running condition, press these buttons to set
the speed to be 3km/h, 6km/h and 9km/h
directly.

- 14 -
Screen
A
Display height and time
B
Display weight and calories
C
Display pulse
D
Display distance and fat
E
Display speed and sex
10、Detailed Instructions
a. Quick start (Manual mode)
1. Switch power on and put the safety key at the appointed position.
2. Press “Start” button, the system will count down in 3 seconds, which displays on
the screen! The machine will run at the speed of 1.0km/h.
3. According to your needs, press “SPEED △or ▽” to change speed
4. When hands are on hand heart rate sensors for 5-8 seconds, heart rate will be
displayed on the screen.
b. Count-down mode：
In ready condition, press “MODE” button to select countdown modes. After finish
selection and reset “Time/Distance/Calories”, press “Start” button to start the
machine!

- 15 -
1. In “Time Mode”, the screen displays flashing “15：00”. Then press “SPEED △or
▽” to reset time from 05：00—99：00.
2. In “Distance Mode”, the screen displays flashing “1.0”. Then press “SPEED △or
▽” to reset distance from 0.5—99.9.
3. In “Calories Mode”, the screen displays flashing “50”. Then press “SPEED △or ▽”
to reset calories from 10—999.
c. Built-in program
There are 99 built-in programs, from P1 to P99. In ready condition, press “PROG.”
button to select one program from P1-P99. After that, press “MODE” button to set
time from 5：00—99：00. Then press “START” button to start the machine.
Every built-in program is divided into 10 periods, each period lasts 1/10 of set time.
During every period, press “SPEED △or ▽” to change speed and press “INCLINE △or
▽” to change incline if necessary. From one period to another, there will be a sound
like “Bi” for 3 times, then speed and incline will be changed according to built-in
programs. After finishing one program, there will be a sound like “Bi” for 3 times,
then the machine will stop slowly and the screen will display “End”. The machine will
be in ready condition in 5 seconds.
d. User-defined program
Besides 99 built-in programs, there are 3 user-defined programs for you to set your
own exercise programs
Set
In ready condition, press “PROG.” button continuously to U1-U3, they are user-
defined programs. After selecting U1, U2 or U3, press “MODE” to set. Press “SPEED △
or ▽” to change speed and press “INCLINE △or ▽” to change incline for the first
period. Then press “MODE” key to confirm the first period and set next period. After
setting all 10 periods, press “START” button to start the machine.
User-defined programs will be kept in the machine forever unless you reset them.
These data will not disappear if power off.
e. Body fat measurement：
In ready condition, press “PROG.” button continuously to “FAT”. Press “MODE”
button to select “HEIGHT”, “WEIGHT”, “AGE”, “SEX” and “FAT”. Press “SPEED △or ▽”
to set above data. Then press “MODE” to “FAT” screen. At this time, put your hands
on the hand heart rate sensor for 5-8 seconds. Then you will see body fat displayed
on the screen.
Please find out whether your weight and height fits according to the following form.
(These data is only for reference, not for medical use）

- 16 -
F-1
SEX
1-MAN
0-WOMAN
F-2
AGE
10-99
F-3
HEIGHT
100-220
F-4
WEIGHT
20-150
F-5
FAT
≤19
Thin
20—25
Fit
25—29
Overweight
≥30
Obesity
f. Power saving：
When the power is on, if the machine doesn’t work for 10 minutes, it will sleep and
the screen will be off. Press any key to wake up the machine.
11、Maintenance
Maintain the machine
Proper maintenance can always keep the machine in good condition.
1. Do not use sand paper or solvent to clean the machine.
2. Controlling parts can not be exposed in the sun or humid environment.
3. Check and tighten all parts regularly. Replace broken parts immediately.
Adjust the running belt
The running belt is well adjusted before being packed. After a period of use, the
running belt may loosen or deflect, which is normal. Then it is necessary to adjust the
running belt, otherwise there will be friction damage to the running belt.
1. Tension:
a) Keep the machine at the speed of 3km/h.
b) Put the multi-wrench into the left adjusting screw and turn clockwise by 1/4
circle.
c) Put the multi-wrench into the right adjusting screw and turn clockwise by 1/4
circle.
d) If necessary, repeat Step b and c as above until the running belt runs smoothly.
Note: These four steps are available to tighten the running belt, if you need to loosen
it, please turn anti-clockwise.
2. Deflection:
a) Keep the machine at the speed of 6km/h.
b) If the running belt deflect to the left, put the multi-wrench into the left adjusting
screw and turn clockwise by 1/4 circle or put the multi-wrench into the right
adjusting screw and turn anti-clockwise by 1/4 circle. (Diagram 1)
c) If the running belt deflect to the right, put the multi-wrench into the right
adjusting screw and turn clockwise by 1/4 circle or put the multi-wrench into the
left adjusting screw and turn anti-clockwise by 1/4 circle. (Diagram 2)

- 17 -
d) If necessary, repeat Step b and c as above until the running belt runs in the
middle.
Deflect to the left (Diagram 1) Deflect to the right (Diagram 2)
Lubricant (White bottle)
All treadmills were added lubricant before packed. However, it is still necessary to
add lubricant after using the machine for 30 hours or 30 days.
How to add lubricant:
a) Cut a small hole at the head of the lubricant bottle. Make sure that the lubricant
can be shot out from the hole.
b) Lift up the running belt and shoot the lubricant to the middle of the running
board.
c) Put down the running belt and put some pressure on the place where you add
lubricant.
d) Start the machine at the speed of 1 km/h for 1 minute.
Cleaning
Clean the machine regularly to extend service life. Here are some tips for cleaning:
a) Please power off and pull the plug before cleaning.
b) Do not use corrosive or liquid material to clean the machine, which shall cause
damage to electronic parts.
c) Frequently wipe out the sweat and dust on the surface, running board or
somewhere else by clean or wet cloth.
d) Please clean the floor around the machine every week.

- 18 -
12、Guides for Malfunction
Analyzing and eliminating malfunction
Item
Malfunction
Reason
Solution
1
The machine
doesn’t work
The safety key is missing
Put the safety key at the right position
The power switch is in “0”
position
Turn power switch to “1”
2
The meter
doesn’t work
The meter and upper
communication line are
not correctly connected
Disassemble the meter and make sure
that the meter and communication line
are well connected.
The upper communication
line is broken
Replace the upper communication line!
3
E0
on the screen
No safety key
If safety key is at the right position,
then check the connecting part and
make sure the safety key is connected
well.
4
E01
on the screen
No signal
Check sensor wire to see whether it is
well connected or whether it is broken.
5
E02
on the screen
Error of PCB
Open circuit of IGBT-CE, replace PCB.
6
E03
on the screen
Big speed fluctuation
If this problem happened when speed
is higher than 8km/h, the machine is
overload, running belt is broken or lack
of lubricant.
If the motor has been used for a long
time, replace the motor or replace the
PCB.
7
E04
on the screen
Error of the
communication line
Check connections of the meter and
under control and make sure they are
all well connected. Otherwise, replace
some lines.
8
E05
on the screen
Current overload
protection
Check the motor. If it’s OK, restart the
machine.
9
E06
on the screen
Error of the motor
Check whether the motor are well
connected, Otherwise, replace the
motor or PCB