Havis-Shields C-VS-1200-F250-1 Configuration guide

4
INSTALL INSTRUCTIONS C-VS-1200-F250-1
Vehicle Specific Console
2008 FORD F-250, 350, 450 and 550 Pickup and Cab Chassis Trucks
TOOLS REQUIRED:
Ratcheting wrench Phillips Screwdriver
Metric/Standard Socket Set T-20 Torx Driver bit
7/16” Wrench 7 mm Socket or Driver
INSTALLATION HARDWARE:
QTY DESCRIPTION PART #
1 ¼” X 1” Hex Bolt GSM33002B
5 ¼” X ½” Carriage Bolt GSM31999
6 ¼” Serrated Hex Flange Nut GSM30023
1 ¼” Flat Washer GSM31005B
3 #8 x ¼” Flat Head Phillips Screw GSM33178
1 Torx Screw Kit C-HK-1
All other hardware is pre assembled on console or OEM hardware is reused.
Always!
 Read all instructions before installing any Havis-Shields Equipment Corp products.
 Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!
 Use only hardware provided with install kit.
 For product support, visit the Install Instructions Section of our website at
http://havis.com/Installation/Installation.html, email [email protected] or call
1-800-524-9900 and ask for technical support.
***Crew Cab trucks will require the removal of the air conditioning / heat duct
that runs on top of the transmission hump to rear seats. Installer will need to
block off remaining duct opening. Screws, foam and duct tape can be used to
close off duct. (Not included)***

C-VS-1200-F250-1_INST_2-08
2
OEM Dashboard Carefully remove the small dash
panel that holds the lighter plug.
Use 7mm socket and remove dash
mount screw
Remove passenger side small
panel.
Use 7mm socket and remove dash
mount screw
Unplug and remove complete
upper dash panel.
Note: Installation can be done
without complete removal, but
install is easier when removed.
Detach lower dash panel under
steering column.
Carefully detach upper dash panel
assembly from spring clips.
Lower dash panels removedUse 7mm socket and remove three mount screws for lower center dash panel

C-VS-1200-F250-1_INST_2-08
3
Assemble the two-piece dash
adaptor panel with three (3) #8 x
¼” Flat Head sheet metal screws.
Use 7mm socket and remove two center dash screws. Reuse these screws and
attach lower console bracket.
Console shipped unassembled
Attach dash panel to console housing with three ¼” x ½” carriage bolts and
flange nuts. Do not tighten yet.
Attach console assembly with two
OEM screws. Only attach two
center screws at this time
Attach console housing to lower
dash bracket with two ¼” x ½”
carriage bolts and flange nuts. Do
not tighten yet.
Attach Dash panel at lower
p
assenger side with ¼” x 1” Hex
bolt and flange nut. Reattach upper
dash panel and driver side lower
dash panel Use OEM dash screws

C-VS-1200-F250-1_INST_2-08
4
Wire and mount all control heads.
N
ote: Installation of lower faceplate screws may
require a T-20 Torx bit in a ratchet wrench with a ¼”
hex socket.
Optional cup holder model C-CUP2-E-C mounted
on side of console. Mount holes must be drilled in
desired location.
Optional Mic Clip brackets model C-MCB mount to
side accessory nuts.
If truck has OEM center console, it will be a
tight fit depending on control heads. This may
require installation of lower faceplates into
console prior to console housing mounting.
The cup holder on OEM console can be
temporarily removed to create more space during
installation. Remove two Phillips screws under
armrest and unclip gray plastic front cap.