Havis-Shields Computer Laptop Mount and Accessories... User manual

INSTALLATION INSTRUCTIONS C-3090’s & C-3089’s
COMPUTER LAPTOP MOUNT AND ACCESSORIES
TOOLS NEEDED:
Ratcheting wrench
Standard socket set
Open-end wrench set
Allen wrench set
Screwdriver set
Always!
 Read all instructions before installing any Havis-Shields Equipment Corp products.
 Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!
 Use hardware provided with install kit
 For product support, visit the Install Instructions Section of our website at
http://havis.com/Installation/Installation.html
1. MOUNTING C-3090-3 or 4 & C-3089-3 or 4 to C-TCB’S
• Photo #3 on page #2 is a basic assembly
instruction of a C-3090-3 (w/ tilt/swivel)
mounting to a C-TCB-x.
• The tilt/swivel assembly, (Photo #1), which
comes pre-assembled to the C-3090 from the
factory, will bolt directly to the rotating plate,
using the hardware loosely attached to the
plate. You do not need to unassembled the
tilt/swivel from the C-3090.
Note: Be sure the 2” fender washer is assembled between
the rotating plate and the tilt/swivel assembly.
2. C-3090-1 or 2 & C-3089-1 or 2 MOUNTING TO
VEHICLE TRAK MOUNTS:
• The C-3090 will come pre-assembled with
tilt/swivel attached.
• Mount trak kit into vehicle.
• Place console and C-3090 into desired
position on trak. (Photo #2)
Note: Be sure assembly does not interfere with dash or
console.
• Slide ¼-20 hex nuts into slots on side of trak
in location to mount C-3090.
• Attach C-3090 to trak using ¼-20 x ½” hex
bolts and washers. Tighten in desired area.
Photo #1
Photo #2

C-3090-INST-10-06
3. ADJUST C-3090 PLATFORM FOR SPECIFIC LAPTOP:
• The C-3090 will need to be adjusted to
properly hold your particular laptop.
Note: Do not adjust the latch on the underside of the
laptop.
• Loosen the “L” clamps on the sides of
the C-3090. (Photo #4)
• Release the latch on the underside of the
laptop.
• Place laptop on top of C-3090 platform
and close the latch.
• Open laptop and adjust “L” clamps so
they are firm against inside lip of
computer on the latch side.
Photo #3

C-3090-INST-10-06
• Loosen ¼-20 nylock nuts on the plate on underside of laptop assembly and adjust to
width of laptop.
• Adjust “L” brackets to clamp the laptop firm.
• Release latch and test for strength. Adjust if necessary.
4. PLATFORM WIDENING INSTRUCTIONS: (Photo #5)
• On larger laptops, it may be necessary to use a different hole pattern on the plate.
• Remove (#1 in photo #5) ¼” nylock nuts and washers
• Remove (#2 in photo #5) bracket and use alternate mounting holes to create a wider
platform.
5. OPTIONAL SCREEN SUPPORT (C-SS & C-SS-2): (Photo #6)
• With laptop adjusted for C-3090, open screen on computer.
• With screen open, remove ¼-20 nylock nut from “L” tab holding laptop.
• Loosely attach optional screen support as shown.
• Adjust screen support around screen and tighten hardware.
• Test screen movement.
P
hoto #4
#1
#2
P
hoto #5
Photo #6

C-3090-INST-10-06
6. MOUNTING C-TMLOCK
• Photo #7 shows the C-TMLOCK option, which comes assembled from the factory if
ordered with the C-3090.
• Remove 8-32 keps nuts that hold down OEM latch on laptop computer mount.
• Remove Pem studs from laptop computer mount and replace with Pem studs included
with C-TMLOCK assembly.
• Move latch out of way and place C-TMLOCK over Pem studs. Place latch over top of
C-TMLOCK.
• Install keps nuts and tighten.
7. MOUNTING C-ML-MLB TO C-3090 (Photo #8 & 9)
• The map light bracket will bolt to C-3090 on the same frame rail as the support tabs bolt
to.
• Determine exact positioning with laptop mounted on C-3090.
• Attach C-ML-MLB to C-3090 tab rail using ¼-20 x ¾” carriage bolts and nylock nuts.
• Wire map light according to instructions provided.
Photo #7
Mounting location
Photo #8 Photo #9