Havis-Shields K-9 Kit KK-K9-C15-K User manual

INSTALLATION INSTRUCTIONS
KK-K9-C15-K K-9 KIT
1998-2003 S10 BLAZER
TOOLS REQUIRED:
Power Drill
Standard And Metric Socket Sets
6” Extension
7/16” Wrench
Drill Bits – 1/8” Through 3/8”
Phillips Screwdriver
Wire Cutters and Crimping Tool
Ratcheting Wrench
COMPONENTS:
1 K9 Main Housing
1 Dome Light Kit
1 Rubber Mat
1 Front Mounting Adjustable Legs
1 Set Of Tunnel Assemblies
1 Set Of Hinged Window Guards
1 Set Of Aluminum Door Panels
1 Rubber Edge Molding
HARDWARE:
QTY: DESCRIPTION: PART #:
10 #10 X ½” Stainless Phillips Flat Head Screw GSM34150
70 1/4-20 X ½” Stainless Carriage Bolt GSM32022
96 1/4-20 Serrated Nut GSM30023
30 #10 X 1/2 Stainless Phillips Screw GSM34169
15 #10 X 3/4 Stainless Phillips Screw GSM34170
26 1/4-20 X ¾” Stainless Carriage Bolt GSM32024
24 #12 X ¾” Stainless Phillips Screw GSM34177
6 ¼” X 1 ¼” Hex Head Lag bolt GSM33061
2 3/8” X 1 ½” Hex Head Bolt GSM33030
2 3/8” Flat Washer GSM31007
2 3/8” Lock Washer GSM31028
2 3/8” Hex Nut GSM30008
4 3/8” X ½” Flat Washer GSM31021
4 Rubber Feet PRM97609
4 8-32 Keps Nut GSM30027
4 8-32 X 1” Pem Stud GSM32252
4 8-32 X 1” Phillips Machine Screws GSM33112
1 Tube of Silver Silicone PRM97343
SUB ASSEMBLIES:
• Attach dome light with wire to housing ceiling.
• Install rubber edge molding on edges of tunnels

KK-K9-C15-K-INST-5-03
2
REMOVE INTERIOR:
• Remove rear seats in vehicle
• Remove door panels and handles
• Remove seat belt assembly
• Remove carpet in rear.
Note: If doors have electric door switches, they must be reattached to original plug assembly. Switch
assembly must then be wire tied down so it does not interfere with window or door latch operations.
REMOVE OEM DOOR PANELS:
• Remove plastic arm rest section that has window switch in it.
• Remove switch assembly from plastic housing (leave plug on switch)

KK-K9-C15-K-INST-5-03
3
INSTALL DOOR PANELS AND WINDOW GAURDS:
• Install aluminum door panels with hardware provided
• Install hinge and window guard on top of door panel with hardware provided
• Lift window guard to installed position and mark mounting holes
• Install top mounting bracket with #10 x ½ “ screws, making sure that holes in window guards
align with holes in mounting bracket.
Note: It will be necessary to bend the window guards to fit the contour of the vehicle door.
• Install window guard into mounting bracket with 10/32 x ½” machine screws & flat washers.
• Remove protective plastic from door panel and window guard.
INSTALL MOUNTING LEGS:
• Attach mounting legs to hold down plates.
• Attach hold down plates to floor of vehicle
utilizing front seat mounting studs
K9 MAIN HOUSING:
Note: Install side walls to floor using #12 X 3/4” stainless
screws until roof is in place. Keep all bolts loose until entire
unit is mounted
• Install floor of K9 kit into vehicle
• Floor should be placed on top of mounting legs
and centered.
• Install left side wall of K9 unit and attach with
¼-20 x ½” carriage bolts & #12 x ¾” stainless
screws.
• Install right side wall of K9 unit and attach with ¼-20 x ½” carriage bolts.
Driver side mounting leg and plate

KK-K9-C15-K-INST-5-03
4
INSTALL CEILING AND WALLS:
• Install ceiling with ¼-20 x ½” carriage bolts and serrated nuts.
• Install front wall with ¼-20 x ½” carriage bolts
• Install rear wall of K9 unit with ¼-20 x ½” carriage bolts.
INSTALL TUNNELS & DOORS:
• Loosely attach side tunnels to main housing 1/4-20 x ½” carriage bolts or 1/4-20 x ¾”carriage
bolts depending on location.
• Attach step to tunnel.
MAIN HOUSING FINAL STEPS:
• Mount rear housing use ¼-20 x 1-½” lag bolts.
• Tighten all loose bolts in the assembly.
Note: Look under the vehicle & insure there are no obstructions.
Driver Side Tunnel

KK-K9-C15-K-INST-5-03
5
OPTIONAL FAN: If optional fan has been purchased, install at this time.
• Mount dome light switch as desired. A switch box is provided so switch can be mounted to K9
housing in various locations. (side of tunnel housing at top works very well). Wire to 12 volt
power source.
• Sheet metal seams and gaps need to be carefully silicone at floor area. (proper sealing of
compartment will eliminate water from getting under K9 unit)
• Allow silicone to dry overnight before placing in rubber floor mat.
Switch Box