Havis DS-PAN-720 Series User manual

Owner’s Manual
Havis Docking Station
For Panasonic TOUGHBOOK G1 Tablet
DS-PAN-720 Series
DS-PAN-721
DS-PAN-721-2
DS-PAN-722
DS-PAN-722-2
DS-PAN-723
DS-PAN-726
DS-PAN-720-SERIES_OMN_2-20
Havis, Inc.
75 Jacksonville Road
Warminster, PA 18974

Before Beginning
Havis is pleased to provide this Owner’s Manual to aid in the proper installation and use of the
DS-PAN-720 Series Docking Station for the Panasonic TOUGHBOOK G1 Tablet.
For questions regarding the set-up of your DS-PAN-720 Series Docking Station,
please contact Havis at 1-800-524-9900 or visit www.havis.com for additional product support and information.
This Owner’s Manual applies to the following Part Numbers:
DS-PAN-721
DS-PAN-721-2
DS-PAN-722
DS-PAN-722-2
DS-PAN-723
DS-PAN-726
•NEVER STOW OR MOUNT THE DOCKING STATION DIRECTLY IN A VEHICLE AIRBAG DEPLOYMENT ZONE.
•DO NOT USE COMPUTER WHILE DRIVING.
•READ ALL INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION.
•DO NOT STORE, INSTALL, OR OPERATE THE DOCKING STATION WHERE WATER, MOISTURE, STEAM, DUST, ETC.
ARE PRESENT
•DO NOT DOCK OR UNDOCK YOUR COMPUTER UNLESS IT IS POWERED OFF. DOCKING OR UNDOCKING WITH YOUR
COMPUTER IN ON, STANDBY, HIBERNATION, OR SLEEP MODES CAN CAUSE PERMANENT DAMAGE.
•FOR THE DS-PAN-721, DS-PAN-721-2, DS-PAN-722 & DS-PAN-722-2 DOCKING STATIONS: DO NOT CONNECT
DIRECTLY TO VEHICLE VOLTAGE SOURCE: This product requires a certified, automotive grade, Panasonic approved
90W power source rated for a continuous, regulated 16VDC output (Havis Part Number LPS-114 or equivalent).
Failure to comply with this requirement will cause product damage that is NOT repairable and is NOT covered
under warranty.
•FOR THE DS-PAN-723 DOCKING STATION: DO NOT CONNECT DIRECTLY TO VEHICLE VOLTAGE SOURCE: The
Panasonic TOUGHBOOK G1 Tablet requires a certified, Panasonic approved power source rated for a continuous,
regulated 16VDC output. Failure to comply with this requirement will cause product damage that is NOT
repairable and is NOT covered under warranty.
•FOR DOCKING STATION MODELS EQUIPPED WITH A BUNDLED POWER SUPPLY (DS-PAN-722, DS-PAN-722-3,
& DS-PAN-726) REFER TO THE SUPPLIED LIND POWER SUPPLY REFERENCE GUIDE.
•WHEN TABLET IS DOCKED, THE BATTERY WILL ONLY CHARGE BETWEEN 0°C to 50°C (32°F to 120°F).
PLEASE REFER TO PANASONIC TOUGHBOOK L1 OWNER’S MANUAL FOR MORE INFORMATION.
Precautions
•Do not place metal objects or containers of liquid on top of the Docking Station
•If a malfunction occurs, immediately unplug the Power Supply and remove the laptop
•Use only the specified Power Supply (Part # LPS-114) with this Docking Station
•Do not connect cables into ports other than what they are specified for
•Do not leave the Docking Station in a high temperature environment (greater than 85°C, 185°F) for a long period of
time

Specifications
Power Supply Input 16.0 V DC-In
Dimensions 10.0” (25.5 cm) H x 11.4” (28.9 cm) W x 4.4” (11.1 cm) D
Weight 2.55 lbs. (1.16 kg)
Operating Environment -10° C to 50° C (14° F to 122° F)
Storage Environment -40° C to 85° C (-40° F to 185° F)
EU DECLARATION OF CONFORMITY [CWN1]
Manufacturers Name: Havis, Inc.
Manufacturers Addresses: 47099 5 Mile, Plymouth Twp, MI 48170 USA
75 Jacksonville Road, Warminster, PA, 18974, USA
This declaration of conformity is issued under the sole responsibility of the manufacturer.
Product name: Docking Station For Panasonic FZ-G1 Tablet
Model: DS-PAN-72X, where ‘X’ may be any alphanumeric character and which describes product options.
May be followed by any alphanumeric characters which describe product options.
Product Options: This declaration covers all options of the above product which bear the CE Marking.
Is in conformity with the following directives, standards, or other normative documents:
UN ECE Regulation 10 UNECE Regulation 10.05, Paragraph 3.2.9; Clauses 6.5, 6.6, 6.7, 6.9; “Uniform provisions concerning the approval of vehicles
with regard to electromagnetic compatibility”
EMC Directive 2014/30/EU EN 50498:2010, “Electromagnetic compatibility (EMC) -Product family standard for aftermarket electronic equipment in vehicles”
RoHS Directive 2011/65/EU EN 50581:2012, “Technical documentation for the assessment of electrical and electronic products with respect to the restriction
of hazardous substances”
The object of the declaration described above is in conformity with Directive 2011/65/EU of the European Parliament and[CWN2] of the Council of 8 June 2011 on
the restriction of the use of certain hazardous substances in electrical and electronic equipment.
Supplementary Information:
The object of the declaration described above is in conformity with the relevant Union harmonization legislation. This product requires the use of a recommended
E Marked automotive power supply when used within vehicles.
Signed for and on behalf of Havis, Inc:
40799 5 Mile, Plymouth Twp, MI 48170, USA August 13, 2019 Bruce Jonik, Director of Engineering , Havis, Inc.

Parts Included
Alignment Posts Pass-Through Antenna
(Dual, Optional)
Docking Connector
Docking Station
Latch Hook
Mounting Holes (x4)
(VESA 75mm Hole Pattern)
Ground Pins
Barrel Lock Latch Handle
Strain Relief Anchor Points
Ports
Strain Relief Mounting Points
(for use with Hardware Kit Item #6)
Tablet Access Window

Parts Included (continued)
Hardware Kit (HWK-0020)
This Hardware Kit includes:
1. Zip Ties (6)
2. Keys (2)
3. M4 x 0.7 x 12mm long Pan Head Screws (7)
4. Washers, M4 (5)
5. Lock Washers, M4 (5)
6. Zip Tie Mounts (2)
Tools required for installation:
• #2 Phillips Screwdriver
(For attaching Docking Station to VESA 75mm
hole pattern equipment with M4 Pan Head Screws)
j
Antenna Identification
DS-PAN-721-2 & DS-PAN-722-2
k
m
l
Antenna Connectors (TNC) Tablet Interface
TOUGHBOOK G1 Tablet
A
B
AB
A
B
A–PANASONIC LOWER
B –PANASONIC UPPER
no

Port Replication Capability
DS-PAN-1301, DS-PAN-1301-2
DC IN 16V
Antenna Switch
INT / EXT
Ethernet
(RJ45)
USB 3.0 (x2) Serial
(Non-Native)
Antenna (TNC)
Optional: Part IDs
DS-PAN-721-2
DS-PAN-722-2
Power Input VGA
(D-Sub 15 pin)
HDMI

1) Align Docking Station mounting holes with the holes on VESA 75mm hole pattern device.
Using the four (4) M4 x 0.7x12mm Pan Head Screws (Hardware Kit Item 3), eight (8)
Washers, M4 (Hardware Kit Item 4), and four (4) Lock Washers, M4 (Hardware Kit Item 5),
secure the Docking Station to device. Torque screws to 20 in-lbs (2.3Nm) ±10%.
A) Havis Desktop Stand installation (sold separately, Part # DS-DA-218).
B) In-Vehicle mounting system installation.
Installation
Washer, M4
Lock Washer, M4
Desktop Stand
(not included)
ENSURE (4) WASHERS ARE INSTALLED BETWEEN
MOUNTING EQUIPMENT AND DOCKING STATION
Washer, M4
M4 x 0.7x12mm
Pan Head Screws
ENSURE (4) WASHERS ARE INSTALLED BETWEEN
MOUNTING EQUIPMENT AND DOCKING STATION
Washer, M4
Lock Washer, M4
Typical Mounting Device
(not included)
Washer, M4
M4 x 0.7x12mm
Pan Head Screws

Cable Management
1) Tip the Docking Station to a position that is comfortable to work with.
2) Connect all cables that are necessary for computing needs.
3) Use Zip Ties (Hardware Kit Item 1) and/or Zip Tie Mounts (Hardware Kit Item 6) to strain relieve cables.
Strain Relief Points are located above each port and on the bottom of Docking Station and should be
used to anchor each cable.
4) Create a service loop with cables to ensue that no tension is on the connectors and to enable intended
motion.
5) Tie off cables onto a stationary part of the mounting system.
4
5
This loop must be large enough to allow
full range of expected rotation and
extension without stressing connections.
Collect cables to secure to the
mounting system.
(Note: mounting system not included)
M4 x 0.7x12mm
Pan Head Screw
Zip Tie Mount

Operation - Docking
TO ENSURE A PROPER CONNECTION, PLEASE READ
THE FOLLOWING BEFORE DOCKING YOUR TABLET.
Hold your TOUGHBOOK G1 in landscape orientation, ensuring the Docking
Connector is on the bottom. (NOTE: Power Button will be on the bottom right)
Alignment Grooves on the bottom of
Panasonic TOUGHBOOK G1 Tablet.
Your tablet’s Alignment Grooves will
align with the Docking Station’s
Alignment Posts.

1) Ensure Docking Station is unlatched by lifting the Latch Handle.
2) Hold tablet in landscape orientation, with bottom angled toward the Docking Station, aligning the
tablet’s Docking Connector with the Docking Station’s Docking Connector. Lower tablet into the bottom
of the Docking Station while ensuring that the alignment grooves are aligned with the Docking Station’s
Alignment Posts.
3) Pivot tablet so the top pushes against the Docking Station’s rubber bumpers. While holding the tablet
firmly against the bumpers, pull forward and down on the Latch Handle to secure tablet in place.
NOTE: The Latch Handle will drive the Latch Hook over the front of the tablet. Pull the Latch Handle
until it snaps into position.
Operation - Docking (continued)

1) If previously locked, unlock Docking Station using supplied key.
2) While holding tablet with one hand, lift only the Latch Handle up and rearward. Note that Latch Hook is
spring loaded and will follow Latch Handle.
3) Once unlatched grab both sides of tablet, rock forward and carefully lift out of Docking Station, top end
first.
4) For theft deterrence, secure tablet by locking Docking Station with the supplied key (Hardware Kit Item 2).
Operation - Docking (continued)
Operation - Undocking

Related Products
Havis offers a wide variety of accessory products specifically for use with your Docking Station.
For more information or to order, please visit www.havis.com.
LPS-114
90W Power Supply
External in-vehicle power supply and cable for Panasonic
TOUGHBOOK G1 with cigarette lighter adaptor.
DS-DA-218
Desktop Stand for Tablet Docking Stations
Durable stand for mounting tablet Docking Stations for use in
the home or office.
DS-DA-102
Night Eyes II
In-vehicle night time viewing from six long lasting soft true, red
LED lights on a flexible steel gooseneck.
DS-DA-501
Replacement Keys
Set of two (2) replacement keys for DS-PAN-720 Series
Docking Stations.