Havis DS-DELL-904 User manual

Owner’s Manual
Havis Docking Station
For Dell Latitude 7230 Rugged Extreme Tablet
DS-DELL-900 Series
DS-DELL-901
DS-DELL-901-4
DS-DELL-902
DS-DELL-902-4
DS-DELL-903
DS-DELL-903-4
DS-DELL-904
DS-DELL-904-4
DS-DELL-907
DS-DELL-907-4
DS-DELL-900-SERIES-OMN_1-23

DS-DELL-901 DS-DELL-902 DS-DELL-903 DS-DELL-904 DS-DELL-907
DS-DELL-901-4 DS-DELL-902-4 DS-DELL-903-4 DS-DELL-904-4 DS-DELL-907-4
Before Beginning
Havis is pleased to provide this Owner’s Manual to aid in the proper installation and use of the DS-DELL-900 Series
Docking Station for the 7230 Latitude Rugged Extreme Tablet
For questions regarding the set-up of your DS-DELL-900 Series Docking Station, please contact Havis at 1-800-524-9900 or
visit www.havis.com for additional product support and information.
This Owner’s Manual applies to the following Part Numbers:
•NEVER STOW OR MOUNT THE DOCKING STATION DIRECTLY IN A VEHICLE AIRBAG DEPLOYMENT ZONE.
•DO NOT USE THE COMPUTER WHILE DRIVING.
•NE JAMAIS PLACER OU MONTER LA STATION D'ACCUEIL DIRECTEMENT DANS LA ZONE DE DÉPLOIEMENT DES COUSSINS GONFLABLES
D'UN VÉHICULE.
•NE PAS UTILISER L'ORDINATEUR EN CONDUISANT.
•READ ALL INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION.
•DO NOT STORE, INSTALL, OR OPERATE THE DOCKING STATION WHERE WATER, MOISTURE, STEAM, DUST, ETC. ARE PRESENT
•FOR THE DS-DELL-901, DS-DELL-901-4, DS-DELL-902, DS-DELL-902-4, DS-DELL-904, DS-DELL-904-4, DS-DELL-907, DS-DELL-907-4, DOCKING
STATIONS: DO NOT CONNECT DIRECTLY TO VEHICLE VOLTAGE SOURCE: This product requires a certified, automotive grade, Dell/Havis
approved power cable for a 12 V power input. Failure to comply with this requirement will cause product damage that is NOT repairable
and is NOT covered under warranty.
•LISEZ ATTENTIVEMENT TOUTES LES INSTRUCTIONS AVANT DE PROCÉDER À L'INSTALLATION.
•NE PAS ENTREPOSER, INSTALLER OU UTILISER LA STATION D'ACCUEIL DANS UN ENDROIT OÙ L'EAU, L'HUMIDITE, LA VAPEUR, LA
POUSSIERE, ETC. SONT PRÉSENTS.
•POUR LES STATIONS D'ACCUEIL DS-DELL-901, DS-DELL-901-4, DS-DELL-902, DS-DELL-902-4, DS-DELL-904, DS-DELL-904-4, DS-DELL-907, DS-
DELL-907-4 : NE PAS CONNECTER DIRECTEMENT A LA SOURCE DE TENSION DU VEHICULE : ce produit requiert un câble d'alimentation
certifié, de qualité automobile et approuvé par Dell/Havis, pour une entrée d'alimentation de 12 V. Le non-respect de ces exigences
entraînera des dommages au produit qui ne seront PAS réparables et ne seront PAS couverts par la garantie.
Manufacturers Name: Havis, Inc.
Manufacturers Address: 75 Jacksonville Road, Warminster, PA 18974 USA
Declares under our sole responsibility that the product:
Product name: Havis Docking Station For 7230 Latitude Rugged Extreme Tablet
Model: DS-DELL-90X, where ‘X’ may be any alphanumeric character which describes product options.
May be followed by any alphanumeric characters which describe product options.
Product Options: This declaration covers all options of the above product which bear the CE Marking.
Is in conformity with the following standards or other normative documents:
Automotive EMC Directive EN 50498:2010, Electromagnetic compatibility (EMC) -
2004/108/EC: Product family standard for aftermarket electronic equipment in vehicles
Directive 2011/65/EU Restriction of the use of certain hazardous substances (RoHS)
Supplementary Information:
The product herewith complies with the requirements of the Automotive EMC Directive 2004/108/EC,Annex I, 6.5, 6.6, 6.8, and 6.9. This product requires the
use of a recommended e-Marked automotive power supply when used within vehicles.
Warminster, PA, USA December 4, 2017 Bruce Jonik, Director of Engineering , Havis, Inc.
EC DECLARATION OF CONFORMITY in accordance with EN 50498
FCC 47CFR, Part 15 compliance: This is an FCC Class B device. Any changes or modifications to the model DS-DELL-90X-(X) not expressly approved by
Havis, Inc. could void the user's authority to operate this equipment.
•FOR THE DS-DELL-901, DS-DELL-901-4, DS-DELL-902 & DS-DELL-902-4, DS-DELL-904, DS-DELL-904-4, DS-DELL-907, DS-DELL-907-4: DO NOT
CONNECT THE TABLET TO MULTIPLE POWER SUPPLIES. WHEN THE TABLET IS DOCKED, DO NOT CONNECT ANY EXTERNAL POWER
CABLES TO THE TABLET.

Table of Contents
Specifications……………………………………………..............................................................
3
Parts included……………………………………………………………………………………………………….
5
Antenna Identification………………………………….…………………………………………………......
6
Port Replication Capability………………………………………….………………………………..........
7
Installation and Cable Management……………………………………………………………….......
8
Operation
–
Docking………………………………………………………………………........................
10
Operation
– Undocking………………………………………………………………………………………… 12
•Do not place metal objects or containers of liquid on top of the Docking Station
•If a malfunction occurs, immediately unplug the power cable and remove the tablet
•Use only the specified Power Cable (DS-DA-339) with this Docking Station
•Do not connect cables into ports other than what they are specified for
•Do not leave the Docking Station in a high temperature environment (greater than 85°C, 185°F) for a
long period of time
•Do not attempt to dock the tablet backwards, or damage may result (See page 10)
Precautions
Power
Supply Input
DS-DELL-901
DS-DELL-901-4
DS-DELL-902
DS-DELL-902-4
Standard Electronics with Internal Power Supply
Standard Electronics with Internal Power Supply and Quad RF
Advanced Electronics with Internal Power Supply
Advanced Electronics with Internal Power Supply and Quad RF
DS-DA-339
Power
Cable
12 VDC IN NOM
(10-35 VDC-in)
DS-DELL-
903
DS-DELL-903-4
No Electronics
No Electronics with Quad RF None None
DS-DELL-904
DS-DELL-904-
4
DS-DELL-
907
DS-DELL-907-4
Standard Electronics
Standard Electronics with Quad RF
Advanced Electronics
Advanced Electronics with Quad RF
External
Power
Supply
12 VDC IN NOM
(
See external supply
for VDC-in)
Dimensions 10.2” (25.9 cm) H x 10” (25.4 cm) W x 3.5” (8.89 cm) D
Weight 2.75 lbs. (1.25 kg)
Operating
Environment -30° C to 63° C (-22° F to 145° F)
Storage
Environment -40° C to 85° C (-40° F to 185° F)
Specifications

Specifications
10”
254 mm
3.5”
89 mm
Latched
10.2 ”
259 mm
Unlatched
10.7 ”
272 mm
2.95”
75 mm
VESA 75 Mounting
Pattern
M4 x 0.7 Thread
DOCK
CENTERLINE

Ports
Alignment Posts
Docking Connector
Antenna Ports
VESA 75 Mounting
Side USB Port
Strain Relief
Bumpers
Barrel Lock
Latch Handle
LED Power Indicator
Parts Included
Strain Relief

Parts Included (continued)
Hardware Kit (HWK-0031)
This Hardware Kit includes:
1. Zip Ties (4)
2. Keys (2)
3. M4 x 0.7 x 20mm long Pan Head Screws (5)
4. Split Lock Washers (5)
5. Washers, M4 (5)
Tools required for installation:
• #2 Phillips (For M4 Pan Head Screws)
j
Antenna Identification
DS-DELL-901-4, DS-DELL- 902-4 [SHOWN], DS-DELL-903-4, DS-DELL-904-4, DS-DELL-907-4
k
m
l
n
Front View of Docking Station
Rear View of Docking Station
A
B
C
D
BC
LTE MAIN MIM02 GPS WIFI MAIN
A
DLTE MAIN
MIM02
GPS
WIFI MAIN

Port Replication Capability
Rearward Facing Ports –Advanced Electronics
DS-DELL-902, DS-DELL-902-4 [SHOWN], DS-DELL-907, DS-DELL-907-4
USB 3.0
(2X) Serial
USB
TYPE-C
Ethernet
RJ45
Display
Output
Power
Input (12v)
Rearward Facing Ports –Standard Electronics
DS-DELL-901, DS-DELL-901-4 [SHOWN], DS-DELL-904, DS-DELL-904-4
USB 3.0
(2X) Serial
USB
TYPE-C
Ethernet
RJ45
Power
Input (12v)

Port Replication Capability
Side Facing Ports
DS-DELL-901, DS-DELL-901-4, DS-DELL-902, DS-DELL-902-4
USB 3.0
NOTE: THIS DOES NOT APPLY TO THE DS-DELL-903 & DS-DELL-903-4 CONFIGURATION (THESE DO NOT HAVE AN
INTERNAL SUPPLY AND NEED TO BE POWERED WITH THE EXTERNAL PORT WHEN DOCKED).
DO NOT CONNECT ANY ADDITIONAL POWER SUPPLY
TO THE TABLET WHEN IT IS DOCKED. MULTIPLE POWER
SUPPLIES WILL CAUSE DAMAGE TO THE TABLET

Installation
1. Align Docking Station mounting holes with the hole pattern on mounting device. Use the (4) Pan
Head screws with washers and lock washers from the hardware kit (HWK-0031) to fasten the docking
station to the motion device (Hardware Kit Items 3, 4 & 5). Torque screws to 80 in-lbs (9.0 Nm) ± 10%
Hardware Kit Item Numbers
ml n
A) HAVIS In-vehicle mounting system installation (Sold separately)
B) HAVIS Desktop Stand installation (Sold separately)
Hardware Kit Item Numbers
ml
n

2. Install all of the cables that are necessary for your computing needs. Use zip ties (Hardware Kit Item 1)
to strain relieve cables to strain relief points, routing all cables together so they can be attached to the
mounting system
Cable Management
Use as many zip
ties as necessary
to secure cables
Zip tie cables onto
mounting device as
shown. Leave additional
slack to allow motion
device to move freely
without stressing cables.
Create a service loop if
there is excess cable
3. Create a service loop with cable bundle to ensure no tension is on the connectors and to enable
intended motion.
4. Tie off cables onto a stationary part of the mounting system
(Mounting system not included with the docking station)

Operation - Docking
1. Ensure docking station is unlatched by pressing the lock button on the top of the docking station.
2. Hold the tablet in the landscape orientation, with the bottom side angled towards the docking station.
Lower the tablet onto the docking station by aligning the tablet alignment sockets with the alignment
posts on the docking station.
⚠CAUTION
DO NOT FORCE TABLET ONTO DOCKING STATION. IF THERE IS RESISTANCE,
CHECK THE ALIGNMENT OF THE TABLET ON DOCKING STATION
⚠WARNING
DO NOT DOCK TABLET BACKWARDS IN THE
DOCKING STATION OR DAMAGE TO THE SCREEN,
TABLET ELECTRONICS, AND DOCKING STATION
ELECTRONICS WILL RESULT
⚠CAUTION

Operation –Docking (Continued)
3. Pivot the top of the tablet into the docking station and apply light rearward pressure to the
top center of tablet or handle. Apply pressure until the tablet is fully seated. Secure tablet by
closing the latch, push downward until you hear the click of the latch which indicates the latch
is securely closed.
4. For theft deterrence, secure tablet by locking the docking station with the supplied key
(Hardware Kit Item 2)

Operation - Undocking
2. While securely holding the tablet, push the lock button on the top of the docking
station until the latch hook releases.
1. If previously locked, unlock Docking Station using the supplied key.
3. Once unlatched, remove the tablet by rocking the top of the tablet away from the
docking station and carefully lift out of the docking station, top end first.

Havis offers a wide variety of accessory products specifically for use with your
Docking Station. For more information or to order, please visit www.havis.com.
DS-DA-339
Power Cable
Power cable for DS-DELL-901, DS-DELL-901-4, DS-DELL-902, DS-
DELL-902-4 Docking Stations.
DS-DA-218
Desktop Stand
Durable stand for mounting the DS-DELL-900 Series Docking
Station in the home or office.
DS-DA-502
Replacement Keys
Set of (2) replacement keys for DS-DELL-900 Series Docking
Stations
Related Products
LPS-178
Power Supply w/Cigarette Input Cable
LPS-179
Isolated Power Supply w/Cigarette Input Cable
LPS-180
Isolated Power Supply w/Hardwired Input Cable
LPS-181
AC Power Supply w/Hardwired Input Cable
LPS-182
Power Supply w/USB-C Power Output Cable