Hawk OptioLaser L100 User manual

Sultan Sonar Manual Rev 1.0
A Higher Level of Performance
www.hawkmeasurement.com
For more information, please visit >
OptioLaser
L10 0
Level, Distance & Position Measurement
of Solids and Liquids
Manual
>

Table of Contents
OptioLaser L10 0
2
Table Of Contents
Overview 3
Principle of Operation 3
Applications 3
Features 3
Quick Start Guide 4
Laser radiation information 6
Labels 7
Apendix A 8
Specifications 8
Apendix B 9
Dimension Drawings 9
Part Numbering 10
PROPRIETARY NOTICE
The information contained in this publication is derived in
part from proprietary and patent data. This information has
been prepared for the express purpose of assisting operating
and maintenance personnel in the efficient use of the
instrument described herein. Publication of this information
does not convey any rights to use or reproduce it, or to use
for any purpose other than in connection with the installation,
operation and maintenance of the equipment described
herein.
WARNING
This instrument contains electronic components that
are susceptible to damage by static electricity. Proper
handling procedures must be observed during the removal,
installation, or handling of internal circuit boards or devices:
Handling Procedure:
1. Power to unit must be removed prior to commencement
of any work.
2. Personnel must be grounded, via wrist strap or other safe,
suitable means, before any printed circuit board or other
internal devices are installed, removed or adjusted.
3. Printed circuit boards must be transported in a conductive
bag or other conductive container. Boards must not be
removed from protective container until the immediate time
of installation. Removed boards must be placed
immediately in a protective container for transport, storage,
or return to factory.
>
<

Overview
3
Principle of Operation
The OptioLaser L100 uses time-of-flight laser technology for continuous non-contact distance or level
measurement. Able to measure any solid or liquid surface, at any angle, the L100 an ideal sensor for level,
positioning and detection applications.
• Non-contact measurement with laser technology
• Level, distance & position measurement of solids and
liquids.
• 303 Stainless steel housing
• Measurement range up to 50 m (164’)
• Continuous measurement,10 mm (0.39”) resolution
• NAMUR compliant 4 … 20 mA output
• 2 Normally open relay outputs
• Easy conguration via USB
• Optional Dust tube accessory (L100/DT) and
Swivel mounting bracket (L100 /SB)
Features
OptioLaser L10 0
Applications
Level control Distance measurement Positioning Blockage detection
>
<

Quick Start Guide
4
OptioLaser L10 0
1. CAUTION - The OptioLaser L100 Sensor contains a laser. Do not look at the beam directly with
optical instruments.
2. Download the Laser Terminal Software from hawkmeasurement.com/downloads/
3. Open the Laser Terminal Package and follow the installation instructions. Everything needed for
communicating with the L100 will automatically be installed.
4. Plug a USB cable into the USB A connector in the terminal compartment of the L100 .
5. Plug the other end of the USB cable into a PC and the L100 ’s LED indicators will light up.
6. Open Terminal software on the PC, a connection with the L100 will automatically be established using
baud rate of 115200,8,n,1.
7. Click the “Connect” icon to open a communications port and the distance measured in meters, the milliamp
output and the signal strength as a percentage will begin to scroll in the Terminal window.
8. If an automatic connection is not created, click the “Laser” icon and select the appropriate USB port and
115200 baud rate.
9. To access the configuration settings menu of the L100, press the <CORRESPONDING> key on the
keyboard:
Menu Selection Default Description
<A>
4 … 20 mA
settings
<B> 4 mA 25.00 m Enter the distance corresponding to the 4 mA output value.
<C> 20 mA 0.60 m
Enter the distance corresponding to the 20 mA output value.
<D> Fail safe
current
> 21.0
mA
Enter the failsafe condition of the 4...20 mA range for alarm
indications.
<E> Test 21.50 mA Output test of the 4 ... 20 mA.
<F>
Relay
settings
<G> Relay A switch
point 1
1.00 m First distance at which Relay A activates.
<H> Relay A switch
point 2
2.00 m Second distance at which Relay A activates.
<I> Relay A mode near =>
closed far
=> open
Select polarity of the relay
<J> Relay B switch
point 1
1.00 m First distance at which Relay B activates.
<K> Relay B switch
point 2
2.00 m Second distance at which Relay B activates.
<L> Relay B mode near =>
closed far
=> open
Select polarity of the relay
<M> Relay test A:closed
B:closed
Tests relay functionality.
>
<

Quick Start Guide
5
OptioLaser L10 0
Menu Selection Default Description
<N>
System
settings
<O> Measuring
units
meters Enter the required measuring units, either meters or feet.
<P> Zero distance
offset
0.00 m
Enter the distance corresponding to the zero datum trim.
<Q> Lost signal
timeout
4.0 sec Enter the lost signal hold time delay in seconds.
<R> Smoothing
filter
ON Turns the smoothing filter OFF (raw) or ON (filtered).
<S> Filling rate
filter
OFF Turns the filling rate filter OFF (fast filling) or ON
(slow filing).
<U> Moving
obstacle filter
ON Turns the moving obstacle filter OFF (raw) or ON
(reject obstacles).
<V> Obstacle filter
size
16 results If the “Moving obstacle filter” is ON, this buffer allows for
selection of the number of results used to reject obstacles.
10. Press the appropriate keyboard key to select a menu item, e.g. type <A> for “a: Hide 4-20 mA settings” to
show or hide the 4-20 mA settings menu.
11. To restart measurements, press the <SPACE> keyboard key.
12. To save a copy of the current screen data, click the “Save” icon.
13. If you wish to start recording data, click the “Log” icon.
14. To clear the screen of measurement data, click the “Clear” icon.
15. Once you have configured the L100 , click the “Disconnect” icon and disconnect the USB cable from the
unit.
16. Connect the 24 V power supply, the 4 … 20 mA output, and the relays, as necessary for your application.
>
<

6
Connections & Instructions for Safe Use
OptioLaser L10 0
USB
connector
+ 24 V dc
4...20 mA
Relay A
Earth
Relay B
+ 24 V power supply
RS485+
RS485-
RB
RA
4.. 20mA
COM
+24 V
COM
Load
RS485-
RS485+
COM
Load
+ 24 V
+ 24 V
COM
Load
unit in milimeter (inch)
L100
L100/DT
63.5 (2.36)
144 (5.51)
M20 Cable
gland M5 Mounting holes
40 (1.57)
34 (1.34)
110 (4.33)
140 (5.51) Ø8.5
4 Holes on 120 PCD
Figure 1 :: Connection diagram
The L100 is a laser rangefinder that emits ionizing laser radiation. The level of the laser emission is Class
1M which indicates that the laser beam is safe to look at with the unaided eye but must not be viewed using
binoculars or other optical devices at a distance of less than 15 meters. Notwithstanding the safety rating,
avoid looking into the beam and switch the unit off when working in the area.
CAUTION -- The use of optical instruments with this product will increase eye hazard.
The L100 should not be disassembled or modified in any way. The laser eye safety rating depends on the
mechanical integrity of the optics and electronics so if these are damaged do not continue using the L100 .
There are no user serviceable parts and maintenance or repair must only be carried out by the manufacturer
or a qualified service agent.
No regular maintenance is required for the L100 but if the lenses start to collect dust then they may be wiped
with suitable lens cleaning materials. Make sure that the L100 is switched OFF before looking into the lenses.
The L100 should be mounted using the four holes provided in the circuit board. Do not hold or clamp the lens
tubes as this may cause damage and adversely affect the laser safety rating.
Specification Value / AEL Notes
Laser wavelength 905 nm
Pulse width < 20 ns
Pulse frequency < 36 kHz
Peak power < 10 W 50 millimeter aperture at 2 meters
Average power < 0.6 mW 7 millimeter aperture
Average energy per pulse < 300 nj
NOHD 15 m Distance beyond which binoculars with may be used safely
Laser radiation information
>
<

7
Labels
OptioLaser L10 0
Labels
Power Supply: 220/110VAC or 24VDC
(12-28VDC)
Max Current: 100 mA
Output: 4-20 mA, 2 x Relays (N/O)
Programming: USB
Laser Safety: Class 1M & Class 2 (aim)
Enclosure Rating: IP66
Temperature: -20 to 60°C (-40 to 140ºF)
AU: [phone]
US: [phone]
hawkmeasurement.com
OptioLaser L100 Laser Transmitter
Power Supply: 220/110VAC or 24VDC
(12-28VDC)
Max Current: 100 mA
Output: 4-20 mA, 2 x Relays (N/O)
Programming: USB
Laser Safety: Class 1M & Class 2 (aim)
Enclosure Rating: IP66
Temperature: -20 to 60°C (-40 to 140ºF)
AU: [phone]
US: [phone]
hawkmeasurement.com
OptioLaser L100 Laser Transmitter
Figure 2 :: Labelling on the OptioLaser L100
>
<

8
Specications
Apendix A
OptioLaser L10 0
Performance data
Sensing range 0.3 ... 50 m (0.98’ ... 164’)
Resolution 10 mm (0.39”)
Accuracy <0.1% of full range at 20°C
Update rate 5 readings per second
Technical data
Power supply 24 V dc nominal (12 ... 28 V dc)
Current consumption 100 mA nominal
Output
Analog 4 ... 20 mA NAMUR compliant self-powered & non-isolated. 2 x Relays (N/O), 42
V dc at 1.3 A.
Communication USB at 115200 baud 8-N-1
Mechanical data
Diameter L100 : 63.5 mm (2.36”) L100/DT: 110 mm (4.33”)
Length L100 : 144 mm (5.51”) L100/DT: 200 mm (7.87”)
Weight L100 : 1.25 kg (2.76 lb) L100/DT: 0.83 kg (1.83 lb)
Connection Flange accessory (L100 /DT) with 4 Ø 8.5 mm holes on 120 PCD
Housing material 303 Stainless steel Powder coated stainless steel
Optical data
Optical aperture 60 mm (2.36”)
Beam divergence < 1° to half power points
Lens material Impact resistant acrylic
Laser safety
classification
Class 1M CAUTION: Do not view laser directly with optical instruments
Environmental data
Operating temperature -20°C ... +60°C
Pressure Atmospheric
Enclosure rating IP66
>
<

9
Dimension Drawings
Apendix B
OptioLaser L10 0
USB
connector
+ 24 V dc
4...20 mA
Relay A
Earth
Relay B
+ 24 V power supply
RS485+
RS485-
RB
RA
4.. 20mA
COM
+24 V
COM
Load
RS485-
RS485+
COM
Load
+ 24 V
+ 24 V
COM
Load
unit in milimeter (inch)
L100
L100/DT
63.5 (2.36)
144 (5.51)
M20 Cable
gland M5 Mounting holes
40 (1.57)
34 (1.34)
110 (4.33)
140 (5.51) Ø8.5
4 Holes on 120 PCD
Figure 3 :: Dimension drawings of the L100
>
<

Part Numbering
Hawk Measurement Systems
(Head O󰀩ce)
15 - 17 Maurice Court
Nunawading VIC 3131, AUSTRALIA
Phone: [phone]
Fax: [phone]
[email protected]
For more information and global representatives: www.hawkmeasurement.com
DOC-OL-L100-MAN v.1.03 0321
OptioLaser L10 0
Hawk Measurement USA
5010 Gateway Drive, Medina, OH 44256, USA
Phone: +1 888 HAWKLEVEL (1-888-429-5538)
Phone: [phone]
Fax: [phone]
[email protected]
OptioLaser L100 Laser Transmitter for Level
Model
LXDT Dust Tube for L100/L200
OptioLaser Laser Level Transmitter
LXHP Handheld Programmer for L100/
L200 OptioLaser Level Transmitter
LXSB Swivel Bracket for L100/L200
OptioLaser Laser Level Transmiteer
OptioLaser L100/L200 Laser
Transmitter Spare Parts
Model
L10 0 OptioLaser Laser Level Transmitter (up to 164ft)
L200 OptioLaser Laser Level Transmitter (up to 328ft)
Dust Tube + USB Programming Cable
(Required for every OptioLaser L100/L200)
DT Dust Tube, Stainless Steel
Accessories - Handheld Programmer
(Optional)
HP Handheld Programmer
XX Not Required
Accessories - Swivel Bracket
(Optional)
SB Swivel Bracket
XX Not Required
L100 DT HP SB
<