Haworth Beside User manual

1 of 6 7029-9983 Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: [phone]
4450-150
IMPORTANT SAFETY INSTRUCTIONS
For use with Beside Pantry
For Comercial Use Only
This product conforms to UL962, certied to CAN/CSA C22.2 No. 203
When using an electrical furnishing, basic precautions should always be followed, including the following:
Read all instructions before using this table.
DANGER- To reduce the risk of electric shock:
1. Always unplug this furnishing from the electrical outlet before cleaning.
WARNING- TO REDUCE THE RISK OF BURNS, FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS:
1. Unplug from outlet before putting on or taking o parts.
2. Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.
3. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not
recommended by the manufacturer.
4. Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped or
damaged, or dropped into water. Return the furnishing to a service center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Do not use outdoors.
7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
8. To disconnect, turn all controls to the o position, then remove plug from outlet.
9. WARNING: RISK OF ELECTRICAL SHOCK. CONNECT 120 VAC POWER OUTLET TO A PROPERLY
GROUNDED OUTLET ONLY.
5VDC 20 Watt USB charger outlet accessory has a class 2 transformer. The plug conguration is shown below. The USB
charger accessory should be plugged into supply outlet conguration shown above.
GROUNDED
OUTLET BOX
GROUNDED
PIN
GROUNDED
OUTLET
GROUNDED
OUTLET
or
SAVE THESE INSTRUCTIONS
The 120VAC power outlet accessory must be grounded. If it should malfunction or breakdown, grounding provides a path
of least resistance for electric current to reduce the risk of electrical shock. The 120VAC power outlet accessory is equipped
with a cord having an equipment grounding conductor and a grounded plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
DANGER- Improper connection of the equipment grounding conductor can result in a risk of electric
shock. Check with a qualied electrician if you are in doubt as to whether the product is properly grounded. Do not
modify the plug provided with the product. If the plug will not t the outlet, have a proper outlet installed by a
qualied electrician. No plug adapter should be used with this product. See illustration below of 120VAC power
outlet accessory plug and proper supply outlet conguration.

2
J
B
B
H
3
or
Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: [phone]
42 of 6450-150 7029-9983
Tools Required
Storage Pantry - Desk Height
Installation Instructions
BESIDE®
1
H
H1
A
B
E
D
#8 x 1/2" Screw Metal Screw
(B)
TRANSFORMER INSTALLATION (OPTIONAL)
#10 x 5/8" Pan Head Screw
(E)
E
F
G
HB
D1
or
1
H
H1
or
3
#8 x 1/2" Screw Metal Screw
(B)
(G)
M5 X 25mm Washer Head Screw
OPEN FULLY BEFORE
CONNECTING WIRING
IMPORTANT!
#1 & #2
1/8"

Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: [phone]
43 of 6450-150 7029-9983
2
3
Stop 1/2 way
Loosen screws
1Level Unit
A
A1
Adjust
0.0”
5a Tighten Screws
4
K
WHEEL ADJUSTMENT
1
6Adjust glide to touch cabinet
A2
L
5b
Install Screw
Remove
Screw
C
C
#10 x 5/8" Truss, Serrated Screw
(C)

Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: [phone]
44 of 6450-150 7029-9983
#8 x 1/2" Screw Metal Screw
(B)
#10 x 5/8" Pan Head Screw
(E)
E
F
D1
G
2
3
G
B
D
1
2
D2
BEND ALL
4 SIDES OUT
(G)
M5 X 25mm Washer Head Screw

Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: [phone]
45 of 6450-150 7029-9983
OPTIONAL - REMOVAL/INSTALLATION
1
2

Rev:
Part No:
Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: [phone]
46 of 6450-150 7029-9983
1-5/8” (1.63) 1-5/8” (1.63)
5-5/8”
(5.63)
8-5/8”
(8.63)
FRONT EDGE OF WORKSURFACE
RIGHT EDGE OF WORKSURFACE
LEFT EDGE OF WORKSURFACE
30” DEEP UNIT - FRONT PILOT HOLE LOCATION
24” DEEP UNIT - FRONT PILOT HOLE LOCATION
RIGHT SIDELEFT SIDE
PLACE TEMPLATE
ON BOTTOM
OF WORKSURFACE
1/8"
Drill
1/2”