Haws 3511 Guide

10/19 Model 3511 Page 1 of 4
1455 Kleppe Lane Sparks, NV 89431-6467 [phone] Fax [phone]
E-mail: [email protected]  website: www.hawsco.com
No. 0002074001 (18)
Model 3511
Drinking Fountain
INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
LIMITED WARRANTY
HAWS warrants that this specific product is guaranteed against defective material
or poor workmanship for a period of one year from date of shipment. HAWS
liability under this warranty shall be discharged by furnishing without charge F.O.B.
HAWS Factory any goods, or part thereof, which shall appear to the Company upon
inspection to be of defective material or not of first class workmanship, provided that
claim is made in writing to Haws within a reasonable period after receipt of the
product. Where claims for defects are made, the defective part or parts shall be
delivered to the Company, prepaid, for inspection. HAWS will not be liable for the
cost of repairs, alterations or replacements, or for any expense connected therewith
made by the owner or his agents, except upon written authority from HAWS,
Sparks, Nevada. HAWS will not be liable for any damages caused by defective
materials or poor workmanship, except for replacements, as provided above. Buyer
agrees that HAWS shall not be liable for general, special, or consequential
damages claimed to arise under the contract of sale. The drinking fountain
manufactured by HAWS is warranted to function if installation and maintenance
instructions provided are adhered to. The units also must be used for the purpose
for which they were intended.
NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED,
PROVIDED OR GIVEN BY HAWS.
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:
TECHNICAL SUPPORT: 1-800-766-5612
FOR CUSTOMER SERVICE: 1-888-640-4297

10/19 Model 3511 Page 2 of 4
RECOMMENDED TOOLS: Hack saw, pipe joint sealant, screwdriver, level, 12"
adjustable wrench, 10" pipe wrench, 9/16”, 1/2”, 7/16” socket wrench or open-end
wrench, 5/32” hex key wrench.
LOCATION OF UNIT: The Model 3511 Drinking Fountain is a wheelchair accessible
drinking water facility. The height dimensions shown, meet current ADA
requirements. When installing this unit, local, state or federal codes should be
adhered to. If height other than shown is required, then dimensions must be adjusted
accordingly.
SUPPLY LINE: The minimum recommended line size is 1/2“IPS with 30-90 psi (2-6
ATM) flowing pressure. Where sediment or mineral content is a problem, an inlet
filter is recommended.
PLUMBING CONNECTIONS: Inlet is 3/8”O.D. compression fitting. Waste outlet is
1-1/2” O.D. tailpiece.
MAINTENANCE: Periodically clean the strainer. Refer to 5874 Series Valve Manual
for more information.
TROUBLESHOOTING
PROBLEM
REPAIR CHECKLIST
1.
Insufficient bubbler flow.
1a.
Check that inlet screwdriver stop valve
is in wide-open position.
b.
Verify minimum 30 psi flowing supply
pressure.
c.
Clean strainer. See 5874 Series Valve
Manual.
d.
Adjust valve to increase flow. Use
front adjust screw or see 5874 Series
Valve Manual.
e.
Clean screens (inside nozzle body).
Unscrew nozzle insert and very gently
activate water supply to pop out qty. 3
screens (be careful not to lose
screens). Remove any debris clogging
the screen openings and place back
into nozzle body. Reassemble nozzle
insert.
General Notes:
Before tightening nut and ferrule assembly, push tubing into fitting until it bottoms out to
ensure correct engagement with O-Ring.
For more information about Haws products, see our website: www.hawsco.com
© 2019 Haws®Corporation –All Rights Reserved
HAWS® and other trademarks usedin these materials are the exclusive property of Haws Corporation.

5705
BUBBLER HEAD
STRAINER
0005624292
5874PB VALVE
MODEL 6250LF BIB FAUCET
(OPTIONAL)
MUST BE USED WITH 6250LF
SPANNER WRENCH
0006983506
ACCESS PLATE
0004521763 6635
SAND TRAP
W/MOUNTING PLATE
(OPTIONAL)
A
STYLE B
(TUBING CONNECTS TO
INSERT ASSY)
FOUNTAIN COULD HAVE EITHER STYLE
STYLE A
(TUBING CONNECTS
TO ELBOW)
ROTATED 90° INTO VIEW
DETAIL A
(OPTIONAL)
FOR REMOVAL
OF NOZZLE
WITH TUBE
0002082253
(OPTIONAL)
APPROVED
DRAWN
PART NUMBER
SCALE: SHEET OF
REVISION
DRAWING TYPE: SIZE: A
BYECN NO.
DATE
DATE
ECN:
REVISED PER
CHKD
Haws Corporation - All Rights Reserved
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
CR
MODEL(S)
1455 KLEPPE LANE
SPARKS, NEVADA 89431
[phone] FAX [phone]
E-MAIL: [email protected]
WEBSITE: WWW.HAWSCO.COM
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER.
P.M. 05-03-00
18
0002074001
3511
1:4
11
IR 12/09/19
.
DP
PARTS BREAKDOWN
5438
2019
FV
PARTS BREAKDOWN
NOTES:
1 5874PB INCLUDES VRK5874 CARTRIDGE ASSEMBLY AND PBA7
RECESSED PUSH BUTTON.
2 ENSURE TUBE IS DISCONNECTED FROM PUSH BUTTON VALVE
BODY PRIOR TO REMOVAL. APPLY ONE DROP OF LOCTITE
222MS TO NOZZLE THREADS PRIOR TO FASTENING BACK ONTO
BUBBLER HEAD. RE-ATTACH TUBE TO VALVE.
3 IMPORTANT: IF HOSE BIB IS USED ALONG WITH A SAND TRAP, IT
MUST BE USED WITH SAND TRAP 6611. CANNOT OFFER HOSE BIB
AS OPTION WITH SAND TRAP 6635. IF HOSE BIB IS PURCHASED,
ACCESS PLATE, 0004521763, MUST BE USED.
PBA7 PUSH
BUTTON ASSY
VRK5874 VALVE
REPAI R KIT
1
1
1
5705LAMIN
(OBSOLETE -
SHOWN FOR
REFERENCE
ONLY.)
3

6"
152mm
27"
29 3/8"
746mm
686mm
248mm
9 3/4"
MOUNTING DETAIL
248mm
9 3/4"
(SUPPLIED)
359mm
14 1/8""
76mm
3"
76mm
3"
457mm
18"
(TO SPOUT
OUTLET) (TO SPOUT OUTLET)
NOTES:
1
0004521763
1/2" NPT INLET
BIB FAUCET DETAIL
(OPTIONAL)
6250LF
BIB FAUCET INLET
STRAINER
TO
1/2" NPT SCREWDRIVER
STOP, COMPRESSION
FITTING & 3/8" O.D. TUBING
(NOT SUPPLIED)
36"
914mm 40"
1016mm
1. REFER TO 5874 SERIES OPERATION AND
MAINTENANCE MANUAL FOR PUSH BUTTON
AND VALVE INSTALLATION/MAINTENANCE
INSTRUCTIONS.
1 1/2" O.D. TAILPIECE
SAND TRAP
MODEL 6635
W/MOUNTING PLATE
(OPTIONAL)
WASTE
(NOT SUPPLIED)
(NOT SUPPLIED)
FINISHED GRADE
(NOT SUPPLIED)
1/2" IPS SUPPLY
SCREWDRIVER STOP
30" SQUARE
CONCRETE SLAB
(NOT SUPPLIED)
1/2-13 ANCHORS
W/MOUNTING
HARDWARE
(SUPPLIED)
1/2" NPT
1/2" TUBING AND
COMPRESSION FITTINGS
(NOT SUPPLIED)
1/2" TEE
(SUPPLIED)
ACCESS PLATE
(OPTIONAL)
1-1/2" O.D TAILPIECE
2. OPTIONAL SAND TRAP MODEL 6635 W/ MOUNTING
PLATE AND 1-1/2" O.D. TAILPIECE. SEE MODEL 6635
FOR ADDITIONAL INSTALLATION INSTRUCTIONS.
2
APPROVED:
DRAWN:
PART NUMBER
SCALE: SHEET OF
REVISION
DRAWING TYPE: SIZE: A
BY:ECN NO.
DATE:
DATE:
ECN:
REVISED PER
CHK'D.:
Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
CR
MODEL(S)
1455 KLEPPE LANE
SPARKS, NEVADA 89431
[phone] FAX [phone]
E-MAIL: [email protected]
WEBSITE: WWW.HAWSCO.COM
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
P.M.
05-30-00
18
0002074001.D
3511
1:8
11
IR 12/09/19
.
DP
INSTALLATION
5438
2019
FV