Haws 5010.6427SS Guide

03/21 Model 5010.6427SS Page 1 of 4
1455 Kleppe Lane Sparks, NV 89431-6467 [phone] Fax [phone]
E-mail: [email protected]  website: www.hawsco.com
No. 0002075000 (1)
Model 5010.6427SS
INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
LIMITED WARRANTY
HAWS warrants that this specific product is guaranteed against defective material
or poor workmanship for a period of one year from date of shipment. HAWS
liability under this warranty shall be discharged by furnishing without charge F.O.B.
HAWS Factory any goods, or part thereof, which shall appear to the Company
upon inspection to be of defective material or not of first class workmanship,
provided that claim is made in writing to Haws within a reasonable period after
receipt of the product. Where claims for defects are made, the defective part or
parts shall be delivered to the Company, prepaid, for inspection. HAWS will not be
liable for the cost of repairs, alterations or replacements, or for any expense
connected therewith made by the owner or his agents, except upon written
authority from HAWS, Sparks, Nevada. HAWS will not be liable for any damages
caused by defective materials or poor workmanship, except for replacements, as
provided above. Buyer agrees that HAWS shall not be liable for general, special, or
consequential damages claimed to arise under the contract of sale. The drinking
fountain manufactured by HAWS is warranted to function if installation and
maintenance instructions provided are adhered to. The units also must be used for
the purpose for which they were intended.
NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED,
PROVIDED OR GIVEN BY HAWS.
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:
TECHNICAL SUPPORT: 1-800-766-5612
FOR CUSTOMER SERVICE: 1-888-640-4297

03/21 Model 5010.6427SS Page 2 of 4
OPERATION & MAINTENANCE INSTRUCTIONS
FLOW ADJUSTMENT:
Step 1: Gain access to flow adjustment screw by removing cover nut and button (see
Installation Drawing).
Step 2: Adjust flow with screwdriver: clockwise for more flow, counterclockwise for
less.
Step 3: If desired flow is not obtained, clean screen located at base of valve body (see
Installation drawing page 4 of 4) and make sure screwdriver stop (not supplied)
is fully opened. Note: To remove head and gain access to screen (for
example, when used with electric water cooler), keep the inlet nipple from
turning by holding it with locking pliers inside the fountain, beneath the basin.
Step 4: Replace button and cover nut.
CARTRIDGE ASSEMBLY REPLACEMENT:
Note: Replacement cartridge, screen, and gasket is available as P/N VRK5010. To gain
access to cartridge assembly with gasket:
Step 1: Remove cover nut and button, then remove retaining nut using universal
spanner wrench (Haws part number 0006983506 –not supplied).
Step 2: Pull cartridge assembly out.
Step 3: Insert new cartridge with gasket.
oDo not remove gasket that comes with new cartridge.
oEnsure that the gasket on the new cartridge is very clean with no debris.
oMake sure there is no foreign matter in the valve body before inserting the
new cartridge assembly with gasket into the valve body.
oWhen inserting cartridge assembly with gasket, align inlet and outlet ports
on cartridge, with holes in the valve body.
oEnsure the cartridge ports are properly aligned and cartridge has
bottomed out by turning slightly into place.
Step 4: Install retaining nut until it makes contact with the cartridge, then tighten 1 1/4
turn farther.
Step 5: Replace button and cover nut.
CAUTION: When replacing cartridge assembly, damage can occur if not properly
re-installed. Read instructions carefully.
OPTIONAL PB8C (COPPER PLATED PUSH BUTTON & NUT) CLEANING & CARE:
If evidence of copper oxidation arises, simply rub surface with a soft rag and salt &
water mixture. Soft cleaning solutions may also be used on the copper button surface.
© 2021 Haws®Corporation –All Rights Reserved
HAWS® and other trademarks usedin these materials are the exclusive property of Haws Corporation

BODY CARTRIDGE
ASSEMBLY
WASHER
WASHER
SCREEN
PARTS BREAKDOWN
RETAINING NUT
FLANGE
NUT
NIPPLE CARTRIDGE
SCREEN
INLET
ASSY.
APPROVED
DRAWN
PART NUMBER
SCALE: SHEET OF
REVISION
DRAWING TYPE: SIZE: A
BYECN NO.
PAGE
DATE
DATE
ECN:
REVISED PER
CHKD
Haws Corporation - All Rights Reserved
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
C
R
MODEL(S)
1455 KLEPPE LANE
SPARKS, NEVADA 89431
[phone] FAX [phone]
E-MAIL: [email protected]
WEBSITE: WWW.HAWSCO.COM
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER.
SLS
01-14-09
1
0002075000
5010.6427SS
N/A
11
FV 03/02/21
4215
JL
3 of 4
PARTS BREAKDOWN
5664
2021
VRK5010
CARTRIDGE
ASSEMBLY
ADJUSTING
SCREW
0003849387
NUT COVER HEX
(CHROME PLATED)
0001333699
PUSH BUTTON
(CHROME PLATED)
CHROME
PLATED
(STANDARD)
0006983506
SPANNER
WRENCH
(OPTIONAL)
0005384011
SPOUT ASSEMBLY
WITH O-RING,
SCREEN & STREAM
STRAIGHTENER
SCREEN
O-RING
PB8C
COPPER
PLATED
ASSEMBLY
(OPTIONAL)
NUT COVER HEX
(COPPER PLATED)
PUSH BUTTON
(COPPER PLATED)
WITH GASKET
SOCKET
WASHER
FIBER WASHER
RUBBER

Ø1 HOLE
3/8"NPT(F)
RUBBER WASHER
FIBER WASHER
COUNTER
LOCK NUT
*NUT COVER
RETAINING NUT
W/GASKET
CARTRIDGE ASSY
(MODEL VRK5010)
FLANGE
*PUSH BUTTON
Ø2 5/32
5 17/32
7/8 MAX.
NOTES:
TO ADJUST FLOW:
1. REMOVE HEX NUT COVER AND PUSH
BUTTON COVER.
2. ADJUST WITH SCREWDRIVER: CLOCKWISE
TO INCREASE FLOW & COUNTER-
CLOCKWISE TO DECREASE FLOW.
3. IF DESIRED FLOW IS NOT OBTAINED,
CLEAN SCREEN AT INLET (SEE 5010.6427SS
OPERATION AND MAINTENANCE MANUAL
FOR ACCESS INSTRUCTIONS.
4. REPLACE PUSH BUTTON COVER AND HEX
NUT COVER.
*CHROME PLATED PUSH BUTTON COVER & NUT ARE STANDARD ON
5010.6427SS. COPPER PLATED OPTION IS AVAILABLE AS MODEL PB8C.
APPROVED:
DRAWN:
PART NUMBER
SCALE: SHEET OF
REVISION
DRAWING TYPE: SIZE: A
BY:ECN NO.
DATE:
DATE:
ECN:
REVISED PER
CHK'D.:
Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
CR
MODEL(S)
1455 KLEPPE LANE
SPARKS, NEVADA 89431
[phone] FAX [phone]
E-MAIL: [email protected]
WEBSITE: WWW.HAWSCO.COM
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
SLS
01-14-09
1
0002075000.D
5010.6427SS
N/A
11
FV 03/02/21
4215
JL
INSTALLATION
5664
2021 PAGE 4 of 4