Hay CAN SOFA User manual

INSTRUCTION MANUAL
CAN SOFA
By Ronan & Erwan Bouroullec

In the Can sofa, Ronan and Erwan Bouroullec are seeking
to go beyond the creation of a practical, elegant and
comfortable design. The intention is to reinvigorate the
whole idea of the sofa, from something inherently
complicated, to something simple, relaxed and for everyone.
The sofa comes flat-packed and is assembled at home, as we
believe people are keen to get things in a quick and simple
way. It is better for all resources, it is less transportation, less
volume, less stock, it is just much easier to do.
INTRODUCTION

CARE AND MAINTENANCE
CAUTION
With a little care you can prolong the life of your
Can Sofa and keep the foam and fabric in
good condition.
Follow the instructions for the materials of your
specific sofa to make sure that it stays in the best
shape for as long as possible.
The information below is only intended as a general
guideline. For more information on how to remove
specific stains, please enquire where you bought
the furniture.
• Always remove stains quickly before they can do
any permanent damage to the furniture.
• Avoid placing the furniture in direct sunlight or
near a strong heat source to reduce changes. HAY
only uses top-quality fabrics but all fabrics fade, and
seams weaken, when exposed to sunlight or strong
heat.
• General exposure to dust and dirt wears down
the fabric. Regular cleaning is important in order
to keep the upholstery looking its best and to
prolong its life.
• The upholstery is fixed and cannot be removed.
• When you move your furniture, make sure you lift it
rather than pulling or pushing it to avoid damaging
the legs and mountings.
• Avoid improper use such as sitting on the back
or armrests, or standing on the sofa.
• Be careful not to scratch or damage the surface
with sharp objects.
• Smooth out creases and wrinkles with your hand
after use to even out the fabric and prevent seam
lines from becoming skewed. (See step 1718).
• Tighten up the screws after one to two months’
use and whenever required.
• Plump the cushions regularly to maintain the
shape.
• Turn the cushions regularly to avoid patinating on
one side only.

POWDER COATED OR CHROMED STEEL
• Wipe with a clean cloth wrung in water or in a
solution of water and a neutral detergent. Remove
soap residue immediately using a clean, dry cloth.
• Avoid using scouring cream or scouring pads, as
they may scratch the surface.
• White spirit (mineral spirit) can be used to
carefully remove stains from chromed surfaces.
• Do not use solvents as they may have an adverse
effect on the coating.
• Never use acetic acid or citric acid.
FABRICS
• Vacuum the furniture regularly to remove dust and
avoid fluff and pilling.
• Straighten the fabric with your hands from time
to time. Wrinkles in the fabric can be straightened
using a steamer.
• Soak up spilled liquids with an absorbent napkin or
cloth by dabbing gently towards the centre of the stain.
• Never use concentrated detergents or bleach,
ammonia or soap intended for hard surfaces.
• We do not recommend spot cleaning of individual
marks and stains as this damages the fabric and
causes colour loss.
• On wool fabrics, most stains can be removed
with lukewarm water on a clean lint-free cloth.
If necessary, add a little neutral detergent. Avoid
rubbing the material hard as this could result in
loss of colour and damage the fabric. It may also
be necessary to use a hairdryer to avoid leaving
an water outline. If the stain persists, consult a
specialist cleaner.
ANILINE LEATHER
• Aniline leather has no or only a light surface
treatment to preserve the leather’s natural surface
and soft touch.
• All natural markings, such as scars and insect
bites, will be visible on aniline leather, which
contributes to the leather’s exclusive appearance.
• This kind of leather is very susceptible to dirt, and
over time it will patinate and become slightly darker.
• Be careful not to scratch the leather.
• Aniline leather is demanding to maintain, and we
recommend that you keep a cleaner and care
product suitable for this type of leather at hand.
Using water may leave a permanent stain on the
surface.
• Do not use sharp objects, strong detergents
or solvents on the leather.
CARE AND MAINTENANCE

PARTS 1-SEATER
Seat frame (A) x 1 Front leg (B) x 2 Back leg (C) x 2
Armrest
tube (D)
x 2
Canvas (F) x 1Backrest
tube (E)
x 1

Allen key
Seat pillow (I) x 1
Back pillow (H) x 1
Side pillow (G) x 2
Screw (J) x 12

Seat frame (A) x 1
Front leg (B) x 2 Back leg (C) x 2 Armrest tube
(D) x 2
Canvas (F) x 1
Backrest tube
(E) x 1
PARTS 2-SEATER

Allen keySeat pillow (I) x 1
Back pillow (H) x 2
Side pillow (G) x 2
Screw (J) x 12

Seat frame (A) x 1
Front leg (B) x 2 Back leg (C) x 2 Armrest
tube (D)
x 2
Canvas (F) x 1
Backrest tube (E) x 1
PARTS 3-SEATER

Allen key
Seat pillow (I) x 1
Back pillow (H) x 3
Side pillow (G) x 2
Screw (J) x 12

1.
Locate the backside of the seat frame (A), marked with a white sticker, and insert
the back legs (C) into each back corner.
2.
Secure the back legs (C) to the seat frame (A) by slightly fastening one screw (J) in
the hole closest to the centre of the sofa.

3.
Pull the legs gently outwards.

4.
Insert the backrest tube (E) into the middle part of the canvas.
2- and 3-seaters: Make sure the backrest tube (E) is facing the right
way. The backrest tube (E) is marked with a white sticker that should
face the outside of the sofa.

5.
Insert the backrest tube (E) into both back legs (C). Make sure the canvas is
mounted with the cotton strap facing outwards. Twist E to hear a “click”.

6.
Insert the armrest tube (D) into the canvas.
Make sure the canvas is kept on the inside of the back leg (C).

7.
Insert the armrest tube (D) into the back leg (C).
Twist D to hear a “click”.

8.
Insert the front leg (B) gently into the frame (A) and armrest tube (D).
Repeat steps 6, 7 and 8 on the other side.

9.
Gently secure the front legs (B) and back legs (C) to the frame (A) by fastening the screws (J)
in all four corners.
It is important NOT to tighten the
screws completely yet.

10.
Flip the frame forward to give easy access to the bottom of the seat frame. Make sure to place
it on the box to avoid scratching the frame.