Hay NEW ORDER User manual

INSTRUCTION MANUAL
CREDENZA
NEW ORDER
By Stefan Diez

CARE AND MAINTENANCE
CAUTION
With a little care, you can prolong the life of your furniture.
Follow the instructions for the materials of your specific
product to make sure it stays in the best shape for as long
as possible.
The information below is only intended as a general
guideline. For more information on how to remove specific
stains, please inquire where you bought the furniture.
• Always remove stains quickly before they can do any
permanent damage to the furniture.
• When you move the shelf, make sure to lift it rather than
pulling or pushing it to avoid damaging the floor and
mountings.
• Tighten up the screws after one to two months’ use.
• Avoid improper use such as putting your feet on the shelf,
or standing on it.
• Use coasters for damp, hot or colored objects to avoid
permanent stains.
• Be careful not to scratch or damage the surface with
sharp objects.
CARE AND MAINTENANCE
Clean with a damp cloth and a mild detergent. Remove
soap residue immediately using a clean, dry cloth.
WARNING
Do not put a TV on this product.
Install the provided safety bracket, before using the
product.

PARTS
Top Shelf (X2)
Middle Shelf (X2)
Bottom Shelf (X2)
Allen Key (X1)
Metal Doors (X2)
Back Panel (X2)
Side Panel (X4)
Safety Brackets (X2)
Double Profile (X4)
Single Profile (X8)
Door Clip (X4)

REQUIRED TOOLS
• Level
• Drill
• Allen Key (provided)
• Six anchor screws, select proper screws for the type of
wall the Credenza will be mounted to.
WEBSITE
For a video that demonstrates how to assemble your
New Order storage, visit www.hay.com/assembly
2.
If the Bottom Shelf is not level, adjust the feet to level the shelf by unscrewing the
four adjustable feet, either by hand or with an Allen Key.
1.
Place a level on the Bottom Shelf to determine if the shelf is level. Make sure both
Bottom Shelves are level, before starting the assembly.
INSTRUCTIONS

3. Mount Double and Single Profiles
SET SCREW PLACEMENT
When mounting the Profiles to the
shelf make sure that the set screws
are pointing towards the middle of
the shelf.
DOUBLE PROFILE
Mount the Double Profiles in the
middle, to connect the two Bottom
Shelves.
SINGLE PROFILE
Mount the Single Profiles in each outer
corner of the credenza.
AVOIDING GAPS
Make sure that the Profiles are
pressed firmly against the shelf
leaving no gaps. Any gaps can lead
to difficulties later on in the assembly
process.

4. Each Profile contains set screws that lock into the shelf in order to stabilize the
construction. When you have finished building the Credenza make sure to tighten all
set screws.

5. Install the Middle Shelves, the second level of Profiles and the Top Shelves.

PANEL INSTALLATION
1. First, install Back Panels by inserting the panel edge into
the channels on the underside of the Top Shelf.
2. When the Panel is in place, use an Allen Key to depress
the tabs (x7 per Panel) to lock the Panel in place.
3. Install the Side Panels by sliding them between the Profiles.
4. When the Panel is in place, use an Allen Key to depress the
tabs (x4 per Panel) to lock the Panel in place.

DOOR INSTALLATION
1. Attach Clips to the underside of the Top Shelf and the surface
of the Middle Shelf by snapping into their respective channels.
3. Attach right-hand door hinge to the Profile by
sliding into the Profile channel.
4. Depress top tab into the underside channel of the
Top Shelf to lock into place. Depress bottom tab into the
Middle Shelf channel to lock into place.
2. Rest right side of the door on the Middle
Shelf. Snap left door hinge into the two Clips
while applying pressure to the back of the Clip.

SAFETY BRACKETS
1. Clip bracket (A) into back side of the Middle Shelf channel, turn
up 90degrees so it is flush with bottom side of Middle Shelf.
2. Match bracket (B) to underside of bracket (A).
3. Mark the location of where you will anchor bracket (B)
into the wall with screws.
4. Pre-drill holes for your screws.
A
B
5. Drill bracket (B) into the wall. Ensure it is flush with the wall.
6. Use Allen Key and provided bolts to screw bracket (B) into bracket (A)
and adjust position if necessary.

05242019
Havnen 1 8700 Horsens Denmark
www.hay.com