Haztec 4-1430 Series User manual

Haztec International Ltd ∙ Moorfield Road ∙ Leeds ∙ LS19 7BN ∙ UK
T: [phone] ∙ inf[email protected] ∙ www.haztec.uk
4-1430-XX 12V 12W
LED Button Hide-Away
M066 Issue 1.1 Created by: Technical - 1 - March 2020
Thank you for purchasing this Haztec product. Before proceeding with installation it is essential
to read and understand this instruction booklet.
Warning!
This product must be installed by persons competent in vehicle electrical installations
Care should be taken to ensure that water ingress cannot occur through mounting or
wiring holes
Regularly inspect the product to confirm correct operation
DO NOT stare directly into the light it produces as permanent damage to the eyes
may result
Use only a mixture of soap and water to clean this product
DO NOT allow solvents and fuels, etc. to come into contact with this product
Basic Operating Specifications:
Supply voltage range:
10-16VDC
Maximum current draw:
1.3A @ 12VDC / 0.65A [Single Colour]
1.3A @ 12VDC / 0.65A [Dual Colour]
Operating temperature range:
-30~50OC
Light source:
4 diode high power LED
Dimensions:
Ø29mm x 40mm
Cable length:
150mm
Wire gauge:
24AWG
Connection Instructions:
Wire
Connect to
Function
Red
Positive [+] via switch/fuse [2A]
Main feed
Black
Permanent negative [-]
Earth / Chassis ground
Blue
Positive [+]
Pattern select
White
Positive [+]
Dim mode
Green
Positive [+]
Steady burn
Yellow1
Positive [+] via switch/fuse [2A]
Second colour
1 Dual-Colour version only
14 Flash Patterns
12VDC
Steady burn function
Alternating & Simultaneous flash
Synchronisation for connecting multiple units
IP68 rated
Flush or screw mount
Optional bracket mount available

Haztec International Ltd ∙ Moorfield Road ∙ Leeds ∙ LS19 7BN ∙ UK
T: [phone] ∙ inf[email protected] ∙ www.haztec.uk
4-1430-XX 12V 12W
LED Button Hide-Away
M066 Issue 1.1 Created by: Technical - 2 - March 2020
Selecting Flash Pattern:
Momentarily apply the BLUE wire to +VDC to advance the flash pattern
Apply the BLUE wire to +VDC for 3-5 seconds to reset to flash pattern 1
FLASH PATTERN
1
Single [120 f/min]
2
Double [120 f/min]
3
Single [SAE]
4
Double [SAE]
5
Quad [SAE]
6
Single fast
7
Double fast
8
Quad fast
9
Quad fast continue
10
Combo 1
11
Combo 2
12
Breathing
13
Random
14
Steady burn
Dual-Colour Flashing:
Apply the RED and YELLOW wires to +VDC together
Both colours will flash alternate
Two colours and dual colour can be set to different flash and directional patterns
Simultaneous or Alternate Flash:
Power up the light
Apply BLUE wire to +VDC for 7 seconds to enter grouping mode
Momentarily tap the BLUE wire to +VDC to change the Group
2 LED flash = Group 1 (default)
4 LED flash = Group 2
Lights in the same group will flash simultaneously
Lights in a different group will flash alternate
Disconnect power to save and exit the grouping mode
The flash pattern will reset to pattern 1
Synchronisation:
Connect the BLUE wire of all lights together
Ensure all lights are set to the same flash pattern

Haztec International Ltd ∙ Moorfield Road ∙ Leeds ∙ LS19 7BN ∙ UK
T: [phone] ∙ inf[email protected] ∙ www.haztec.uk
4-1430-XX 12V 12W
LED Button Hide-Away
M066 Issue 1.1 Created by: Technical - 3 - March 2020
Dim Function:
Apply the WHITE wire to +VDC. The light intensity will decrease to 60% for night
operation
Steady Burn Function:
Apply the GREEN wire to +VDC. Steady burn will operate and over-ride original flash
Installation:
Flush Mount
1. Drill a Ø30mm (1 3/16”) hole in the
panel
2. Install grommet from the front
3. Insert light into the grommet
4. To prevent rotation, apply silicone
sealant around the reverse side if
possible
5. Ensure optical lines align vertically

Haztec International Ltd ∙ Moorfield Road ∙ Leeds ∙ LS19 7BN ∙ UK
T: [phone] ∙ inf[email protected] ∙ www.haztec.uk
4-1430-XX 12V 12W
LED Button Hide-Away
M066 Issue 1.1 Created by: Technical - 4 - March 2020
Screw Mount
1. Drill a Ø30mm (1 3/16”) hole in the
panel
2. Secure the mounting ears onto the
light with the screws provided
3. Secure the light onto the panel with
screws
Bracket Mount
1. Install the grommet onto the bracket
from the front and insert the light
2. Secure the light with a screw and
secure the bracket onto the surface
with screws