Heal-Tech Speedohealer v4 User manual

SHv4_D01_InstallGuide_en.pdf [rev. 003] - 1 -
http://www.speedohealer.com
Install Guide for SH-D01Harness Kit
For use with the following DUCATI motorcycles:
Hypermotard (2007-2010), Monster (2003-2010), Multistrada (2003-2010), ST3
(2004-2007), ST4s (2004-2005), Streetfighter (2009-2010), 749 (2003-2006), 848
(2008-2010), 999 (2003-2006), 1098 (2007-2009), 1198 (2009-2010)
Also fits MV AGUSTA F4 (2003-2010), Brutale (2004-2010)
Disclaimer: Donotattempttoinstalltheproductifyoudon’thavebasicmechanicalskills.
The SpeedoHealer is intended to improve speedometer accuracy. However, HealTech
Electronics Ltd. and its distributors shall not be liable for any loss, damage or penalties
caused by improper installation or inaccurate speed readings.
1. Locating the Speed Sensor coupler
Preparation:
- The ignition key should be in OFF position.
-Raise the rear wheel off the ground by using a stand.
Make sure the rear wheel spins freely.
- Remove the seat.
Ducati: The Speed Sensor is mounted at the rear wheel. Trace the cable from the
sensor until you find the 3-pole black speed sensor connector. The connector is usually
accessible by removing the rightsidefairingandonmostmodels it is in close proximity
of the right side engine cover.
MV Agusta: the connector is at the front sprocket cover.
Ifindoubt,checkthebike’sServiceManualoraskyourdealerforthelocationofthe
Speed Sensor coupler.
Confirmation:
Separate the Speed Sensor coupler (you might need to use a small flathead screwdriver
togetthecouplerapart). Rotate the rear wheel while the ignition is on.
Does the speedometer show 0, turn the ignition off and proceed to the next step.
Otherwise, try again since you have disconnected something else.

- 2 –
2. Installation
1. After separating the Speed Sensor coupler, plug in boththemaleandfemale
3-pole SH harness connectors. Make sure the connectors are fully seated.
2. Connect the 4-pole SH harness connector to the SH box.
3. Check whether the SH is installed and working properly:
- Have the ignition OFF.
- Press SEL and keep it depressed while you turn ignition ON.
[t] (test) is now indicated. Release the button.
The speedo should indicate a number other than zero.
- Rotate the rear wheel.
[t] should be blinking as the wheel turns.
- Press SEL to exit from Test mode.
The speedometer should work the same way as with no SH installed.
If the tests fail, disconnect the 3-poleand4-pole connectors and check
whether the connector pins are bent or pushed out of position.
4. Find a place in your bike for the SH box regarding the followings:
-Tobeabletochangethesettingseasily,placetheunitwhereitis
quickly accessible.
-Frequently wet areas should be avoided.
-Donotplacetheunitveryclosetohotplacesliketheengineor
exhaust pipe.
-Keep at least 2 cm(1”)distancefromother electronics,suchasthe
bike's ECU or a Power Commander.
In most cases, the under-seatcompartmentisthebestlocationforthebox.
Secure the unit with the supplied Velcro strips.
5. Neatly route the SH harness from the 3-pole plugs to the mounting location,
preferably along the frame. To reduce possible interference, try not to route the SH
harness along with other electrical cables.
Do not bend the SH harness near the SHconnector.Otherwisethepinsmaybreak
over time.
To minimize cable stress,usethesuppliedcabletiestofastentheunitandthe
harnesstoasolidpartofthebike.MakesurethattheSHswitcheswon’tbehitby
loose objects in the trunk.
6. IfyouwishtousetheTopSpeedRecallfeature,connect the 2-pole plug of the
remote button.Routetheharnesstowardsthefrontendofthebikeandsecurethe
remote button at the dashboard with the supplied cable ties.
Ifyouwish,youcaneasilychangetheharnesslengthorreplacetheremotebutton
per your liking (any SPST momentary “push-to-make” switch can be used).
7. Please visit www.speedohealer.com and use our on-line calculator to generate
set-up instructions for your SH. Alternatively, refer to the User’s Guide for
instructions.