Heart of House Abingdon 4020897 User manual

23465758
osaka
width: 40,0 cm
depth: 40,0 cm
height 59,6 cm
assembly instructions - please keep for future reference
if you need help or have damaged or missing parts, call the argos customer helpline: 03456 400 800
abingdon
4020897
dimensions
width: 131.5 cm
depth: 50.0 cm
height: 189.9 cm
issue 1 - 08-06-2015
350807-01

!safety and care advice
important - please read these instructions fully before starting assembly
care and maintenance
1
• assembly should be carried
out by a competent adult
only.
• check you have all the
components and tools listed
on pages 2 and 3.
• do not use this product if
any components are missing
or damaged.
• remove all fittings from the
plastic bags and separate
them into their groups.
• keep children and animals
away from the work area,
small parts could choke if
swallowed.
• make sure you have enough
space to layout the parts
before starting.
• do not stand or put weight
on the product, this could
cause damage.
• assemble the item as close
to its final position (in the
same room) as possible.
• assemble on a soft level
surface to avoid damaging
the unit or your floor.
• parts of the assembly will
be easier with 2 people.
• we do not recommend the
use of power drill/drivers for
inserting screws, as this could
damage the unit. Only use
hand screwdrivers.
• dispose of all packaging
carefully and responsibly.
• made for home retail group,
milton keynes.
• only clean using a damp
cloth and mild detergent, do
no use bleach or abrasive
cleaners.
• regularly check fastenings
to ensure they are tightened. • this product should not be
discarded with household
waste.
take to your local authority
waste disposal centre.
note: if required the next
page can be cut out and
used as reference
throughout the assembly.
keep this page with these
instructions for future
reference.

if you have damaged or missing components, call
the argos customer helpline: 03456 400 800
components - panels
please check you have all the panels listed below
2
350807-03
2
(182,1 cm x 45 cm)
side, left
15
(34 cm x 18,2 cm)
drawer back
18
(35,0 cm x 44,7 cm)
drawer bottom
17
(45 cm x 18,2 cm)
drawerside, right
1
(130,4 cm x 50 cm)
top
3
(182,1 cm x 45 cm)
side, right
7
(188,4 cm x 5 cm)
post, left
11
(121,5 cm x 9,2 cm)
front rail
12
(39,8 cm x 7 cm)
back rail, side
10
(156,5 cm x 41,5 cm)
back
8
(188,4 cm x 5 cm)
post, right
16
(45 cm x 18,2 cm)
drawerside, left
14
(40,1 cm x 20,9 cm)
drawer front
9
(154,5 cm x 1,7 cm)
h-profile
5
(121,5 cm x 46,4 cm)
bottom
22
(155,3 cm x 40,1 cm)
door
20
(79,3 cm x 2,2 cm)
hanging rail
19
(124,6 cm x 22,9 cm)
back, small
3
x
3
x
13
(38,9 cm x 7 cm)
back rail
4
(155,0 cm x 46,4 cm)
divider, large
6
(31,9 cm x 46,4 cm)
divider, small
21
(38,8 cm x 2,2 cm)
hanging rail, small
2
x
2
x
2
x
2
x
3
x
3
x
3
x
3
x 3
x

components - ttings
please check you have all the panels listed below
note: the quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
3350807-04
39 ø7.8 x 40mm wooden dowel x
Aa
Cb
ø5 x 8, cc34mm bolt x 33
Ca
ø15 x 10.5mm cam x
41
1.2 x 15mm nail x
Di
50
Kb
ø5.8 x 8mm screw x 12
17060 16040 90 15013070 120100 14011050 803020100
ruler - use this ruler to help correctly identify the screws
tools required
flatblade screwdriver
(medium)
hammer phillips screwdriver
(medium & large)
back fitting w. ø3.5 x 15mm screw x
Fi
6
ø4 x 25mm screw x
Jb
20
54mm handle x
Gm
6
m4 x 20mm screw x
Hd
6
2
Vl
44 x 23 x 23mm angle x
Ko
8 ø4,2 x 9,5mm screw x
ø3.5 x 35mm screw x
Ba
18 ø3 x 12mm screw x
Bo
46
wall strap and instruction x 1
Fh
3
CL
450mm drawer runner, left, side x 3
CR
450mm drawer runner, right, side x
3
DR
450mm drawer runner, right x 3
DL
450mm drawer runner, left x
Mc
9 0mm crossplate x
Mf
6 ø26mm cup hinge x
Fl
4
support for hanger rail - 15mm x
back fitting - 14 x 19mm x
Fc
12
self adhesive bumper, ø10 x 3mm x
Et
6
Pm
door stop x
6
Me
3 ø26mm cup hinge x
Cd
m4, cc34mm bolt x 8
Cm
m4 / ø5 x 12mm threaded tube x
4
ø18 x 9mm Spacer x
Nu
6
Kf
6 ø5.8 x 19mm Screw x

assembly instructions
x the posts
7
and
8
onto the sides
2
and
3
using screws
Jb
into the
holes indicated.
the top of the posts
7
and
8
and the sides
2
and
3
must
be ush.
step 1.1
assembly of the
wardrobe.
step 1
4
350807-05
ø4 x 25mm screw x
Jb
20
Jb
Jb
Jb
Jb
Jb
Jb
Jb
Jb
3
8
7
2
11
5
7
2
8
10
1
3
12
10
9
Jb
Jb
Jb
Jb
Jb
Jb
Jb
Jb
8
10
7
20
Jb
Jb
Jb
Jb
8
7
4
12
13
66
19
21

assembly instructions
x the crossplates
Mc
to the sides
2
and
3
using the pre-mounted
screws.
position the crossplates
Mc
exactly as shown.
x the supports for
hangerrails
Fl
to the
sides
2
and
3
using
screws
Bo
.
step 1.3
knock the dowels
Aa
into the holes indicated
on the sides
2
and
3
.
use a small
hammer.
screw the bolts
Cb
into
the holes indicated on the
sides
2
and
3
.
step 1.2
350807-06
5
Cb
ø5 x 8, cc34mm bolt x 8
6 ø7.8 x 40mm wooden dowel x
Aa
Cb
Cb
Aa
Aa
Aa
Aa
Cb
Cb
Cb
Cb
Cb
Cb
Mc
6 0mm crossplate x
Fl
2
support for hanger rail - 15mm x
ø3 x 12mm screw x
Bo
2
Mc
Mc
Bo
Fl
Mc
Bo
Fl
Mc
Mc
2
3
3
2
Mc

assembly instructions
x the drawer runners
CL
and
CR
to the sides
2and 3using screws
Kf
through the holes
and the spacers
Nu
as
indicated.
see details.
step 1.4
knock the dowels
Aa
into the holes indicated
on the back rails
12
and
13
, the large divider
4
and the small dividers
6
using a small hammer.
step 1.5
6
350808-07
note the hole!
bottom end of
right hand side
1
CL
450mm drawer runner, left, side x
1
CR
450mm drawer runner, right, side x
15
ø7.8 x 40mm wooden dowel x
Aa
2
3
Kf
Kf
Kf
Kf
Kf
Kf
CL
ø18 x 9mm Spacer x
Nu
6
Kf
6 ø5.8 x 19mm Screw x
4
6
13
12
Aa
Aa
Aa
Aa
Aa
Aa
Aa
Aa
Aa
Aa
Aa
2
x
2
x
1
x

assembly instructions
screw one of the bolts
Cd
into each of the threaded
tubes
Cm
.
push the bolt
Cd
+ the
tube
Cm
into the holes
indicated on the dividers
6
and x them using
bolts
Cd
into the threaded
tubes
Cm
from the other
side of the dividers
6
.
step 1.7
x the angles
Vl
using
screws
Ko
into the holes
indicated on the front
rail
11
.
step 1.8
x the drawer runner
CL
to the right hand
side of the dividers
6using screws
Kb
through the holes as
indicated.
turn around the
dividers 6 and x the
drawer runner
CR
to
the left hand side of
the dividers
see details.
step 1.6
350807-08
7
Kb
ø5.8 x 8mm screw x 12
2
CL
450mm drawer runner, left, side x 2
CR
450mm drawer runner, right, side x
Ko
Ko
2
Vl
44 x 23 x 23mm angle x
Ko
4
ø4.2 x 9.5mm screw x
Vl Ko
11
Cb
Cb
Kb
Kb
Cd
m4, cc34mm bolt x
4
Cm
m4 / ø5 x 12mm threaded tube x
2
Cb
ø5 x 8, cc34mm bolt x 2
Vl
2
x
2
x
6
6
Kb
Kb
CL
CR
Kb
Kb
CR
CL
Cd
Cd
Cm
Cd
Cd
Cm

assembly instructions
x the crossplates
Mc
to the divider
4
using
the pre-mounted screws.
position the crossplates
Mc
exactly as shown.
x the support for
hangerrail
Fl
to the left
hand side of the divider
4
using screws
Bo
.
turn around the
divider
4
and x
the support for
hangerrail
Fl
to the
other side using screws
Bo
.
step 1.9
screw the bolts
Cb
into
the holes indicated on the
top
1
.
knock the dowels
Aa
into the holes indicated
on the bottom
5
using
a small hammer.
push the door stops
Pm
into the holes indicated
on the top 1
and the
bottom
5.
step 1.10
350807-08
7
Kb
ø5.8 x 8mm screw x 12
2
CL
450mm drawer runner, left, side x 2
CR
450mm drawer runner, right, side x
Ko
Ko
2
Vl
44 x 23 x 23mm angle x
Ko
4
ø4.2 x 9.5mm screw x
Vl Ko
11
Cb
Cb
Kb
Kb
Cd
m4, cc34mm bolt x
4
Cm
m4 / ø5 x 12mm threaded tube x
2
Cb
ø5 x 8, cc34mm bolt x 2
Vl
2
x
2
x
6
6
Kb
Kb
CL
CR
Kb
Kb
CR
CL
Cd
Cd
Cm
Cd
Cd
Cm
8
350807-09
Cb
ø5 x 8, cc34mm bolt x 9
1
5
Pm Pm
Pm
Aa
Aa
Aa
Aa
Aa
Aa
Cb
Cb
Cb
Cb
Cb
Cb
Pm
door stop x
6
6 ø7.8 x 40mm wooden dowel x
Aa
Pm
Pm
Pm
Cb
Cb
Cb
Mc
3 0mm crossplate x
Fl
2
support for hanger rail - 15mm x
ø3 x 12mm screw x
Bo
2
4
Mc
Mc
Bo
Fl
Mc
Bo
Fl

assembly instructions
screw one of the bolts
Cd
into each of the threaded
tubes
Cm
.
push the bolt
Cd
+ the
tube
Cm
into the holes
indicated on the
bottom
5
.
x them using bolts
Cd
into the threaded tubes
Cm
from the other side of
the bottom
5
.
screw the bolts
Cb
into
the holes indicated on the
bottom
5
.
step 1.11
place the divider 4
onto the
bottom
5
.
push cams
Ca
into the
holes indicated on
the
divider
4
, arrows
pointing towards the
bottom 5.
turn the cams
Ca
to the
right to x the
divider 4.
step 1.12
350807-10
9
Ca
ø15 x 10.5mm cam x 2
4
5
5
Cm
Cd
Cd
Cd
m4, cc34mm bolt x
4
Cm
m4 / ø5 x 12mm threaded tube x
2
Cb
ø5 x 8, cc34mm bolt x 2
Cd Cm
Cd
Cd
Cb
Cb
Ca
Ca

assembly instructions
place the dividers 6
onto the
back rail
13
.
place the
back rails 12
onto the dividers 6.
push cams
Ca
into the
holes indicated on the
back rails
12
and
13
,
arrows pointing towards
the dividers
6
.
turn the cams
Ca
to the
right to x the back
rails 12 and 13 .
step 1.13
place the dividers 6
onto the
bottom
5.
push cams
Ca
into the
holes indicated on the
dividers 6.
turn the cams
Ca
to the
right to x the
dividers 6.
step 1.14
350807-10
9
Ca
ø15 x 10.5mm cam x 2
4
5
5
Cm
Cd
Cd
Cd
m4, cc34mm bolt x
4
Cm
m4 / ø5 x 12mm threaded tube x
2
Cb
ø5 x 8, cc34mm bolt x 2
Cd Cm
Cd
Cd
Cb
Cb
Ca
Ca
10
350807-11
Ca
ø15 x 10.5mm cam x
4
12
13
12
6
6
Ca
ø15 x 10.5mm cam x
4
6
6
5
Ca
Ca
Ca
Ca
Ca
Ca
Ca
Ca

assembly instructions
place the front rail 11
onto the dividers 6.
push cams
Ca
into the holes
indicated on the dividers
6
arrows pointing
towards the front rail.
turn the cams
Ca
to the
right to x the front rail
11
.
step 1.15
place the sides
2
and
3
onto the bottom
5
and
the back rail
12
.
push cams
Ca
into the
holes indicated on the
bottom
5
and the
back rails
12
, arrows
pointing towards the
sides.
turn the cams
Ca
to the
right to x the sides
2
and
3
.
step 1.16
350807-12
11
Ca
ø15 x 10.5mm cam x 2
2
3
5
12
Ca
Ca
Ca
Ca
Ca
Ca
Ca
11
6
6
Ca
Ca
Ca
ø15 x 10.5mm cam x 8
Ca
12

assembly instructions
place the top 1onto
the sides 2and 3
and the divider 4.
push cams
Ca
into
the holes
indicated
on the sides
2and 3and the
divider 4, arrows
pointing towards the
top 1.
turn the cams
Ca
to the
right to x the top 1.
step 1.17
place the front rail 11
as shown.
x the angles
Vl
to the
sides using screws
Ko
.
see detail.
step 1.18
350807-12
11
Ca
ø15 x 10.5mm cam x 2
2
3
5
12
Ca
Ca
Ca
Ca
Ca
Ca
Ca
11
6
6
Ca
Ca
Ca
ø15 x 10.5mm cam x 8
Ca
12
12
350807-13
Ca
ø15 x 10.5mm cam x 9
Ko
Ko
4
ø4,2 x 9,5mm screw x
Ko
2
4
3
1
Ca
Ca
Ca
Ca
Ca
Ca
11

assembly instructions
step 1.19
place two of the backs
10 into the rabbet on
the top 1and onto
the divider 4.
!important!
make sure the
angle between
the top 1and the
sides is 90°.
x the backs 10 to
the top 1using nails
Di
and to the divider
4using screws
Bo
through the back
ttings
Fc
.
nally x the back 10 to
the post 7using
nails
Di
and a small
hammer.
350807-14
13
back fitting - 14 x 19mm x
Fc
5
1.2 x 15mm nail x
Di
21 ø3 x 12mm screw x
Bo
5
4
Bo
Fc
Di
Di
Di Di
Bo
Fc
Fc Bo
Fc Bo
Bo
Fc
10
10
7
5
1

assembly instructions
step 1.20
place the remaining
back 10 into the rabbet
on the top 1, into the
h-prole 9, onto the
post 8
x the back
10
to the
top
1
and the posts
8
using nails
Di
.
place the back 19 onto
the posts 5and 6,
the bottom 5
and the
back rails
12
/
13
.
x
the back 19 to the
posts 7and 8
and
the back rails
12
/
13
using nails
Di
.
nally x the backs
10
and
19 to the bottom
5
using screws
Bo
through
the back ttings
Fc
.
350807-14
13
back fitting - 14 x 19mm x
Fc
5
1.2 x 15mm nail x
Di
21 ø3 x 12mm screw x
Bo
5
4
Bo
Fc
Di
Di
Di Di
Bo
Fc
Fc Bo
Fc Bo
Bo
Fc
10
10
7
5
1
14
350807-15
1.2 x 15mm nail x
Di
29
back fitting - 14 x 19mm x
Fc
7
ø3 x 12mm screw x
Bo
7
4
65
10
19
9
10
10
8
1
13
7
Di
Di
Di
Di

assembly instructions
!
important!
the wardrobe is
heavy. lift with care.
its recommended that
the wardrobe is xed to
the wall.
use the ttings
Fh
.
follow the instructions
included with the
ttings.
step 1.21
350807-16
15
wall strap and instruction x 1
Fh
20
21
20 21

assembly instructions
assembly of the
drawers.
step 2
step 2.3
screw the bolts
Cb
into
the holes indicated on
the drawer front 14 .
x the drawer sides 16
and 17 to the drawer
back 15 as shown,
using screws
Ba
.
step 2.1
knock the dowels
Aa
into the holes indicated
on the drawer sides 16
and 17 using a smal
hammer.
step 2.2
350807-16
15
wall strap and instruction x 1
Fh
20
21
2021
16
350807-17
Cb
ø5 x 8, cc34mm bolt x 12
16
Aa
Aa
17
12 ø7.8 x 40mm wooden dowel x
Aa
Cb
14
Aa
Aa
14
18
16
15 17
15
16
Ba
Ba
17
ø3.5 x 35mm screw x
Ba
18
Cb
Cb
Cb
3
x
3
x
3
x
3
x

assembly instructions
step 2.6
!
important!
make sure the
angle between
the drawer front
14
and
the drawer sides
16
and
17
is 90° before the drawer
bottom
18
is xed using
Fi
as shown.
to adjust the angle between
the drawer sides and the
front push the tting
Fi
sidewards.
see details.
step 2.5
push the drawer front
14
onto the drawer sides
16
and
17 .
place cams
Ca
into the
holes indicated, arrow
pointing towards the front.
turn the cams
Ca
to the
right to x the front.
slide the drawer bottom
18
into the drawer sides
16
and
17
.
step 2.4
90°
350807-18
17
Fi
Fi
Fi
18
14
16
17
Fi
Fi
back fitting w. ø3.5 x 15mm screw x
Fi
6
16
17
Ca
Ca
17
16
18
Ca
ø15 x 10.5mm cam x 12
14
3
x
3
x
3
x

assembly instructions
step 2.7
place the drawer runners
DL
and
DR
onto the drawer
sides
16
and
17
and push
them onto the back of the
front
14
.
x the drawer runners
DL
and
DR
to the drawer sides
16
and
17
using screws
Bo
into the holes indicated.
step 2.8
x the metal handles
Gm
to the drawer front
14
using screws
Hd
.
slide the drawer onto
the runners and into the
wardrobe.
step 2.9
90°
350807-18
17
Fi
Fi
Fi
18
14
16
17
Fi
Fi
back fitting w. ø3.5 x 15mm screw x
Fi
6
16
17
Ca
Ca
17
16
18
Ca
ø15 x 10.5mm cam x 12
14
3
x
3
x
3
x
18
350807-19
m4 x 20mm screw x
Hd
3
Hd
54mm handle x
Gm
3
Gm
14
Bo
Bo
Bo
17
16
Bo
3
DL
450mm drawer runner, left x
3
DR
450mm drawer runner, right x
ø3 x 12mm screw x
Bo
12
14

assembly instructions
step 3
assembly of the doors.
place the cup hinges
Me
and
Mf
into the holes
indicated on the
doors
22
.
x the hinges using
screws
Bo
.
step 3.1
350807-20
19
ø3 x 12mm screw x
Bo
18
Mf
6 ø26mm cup hinge x
Bo Bo
Mf
Bo
Bo
Mf
Mf
22
22
22
Door, left
Door, right
Door, center
Large
Mf
Small
Me
Door, right
Door, center
Door, left
Large
Mf
Me
3 ø26mm cup hinge x
22
22
22
Me
Bo
Mf
Mf
Bo
Bo
Mf
Me
Bo
Bo
Me
Bo Bo