HeartSine samaritan PAD 300P User manual

HeartSine PAD 300P Trainer User Manual 1
HeartSine®
HeartSine®
HeartSine samaritan®PAD
300P Trainer
User Manual
model TRN-300

2 www.heartsine.com
HeartSine samaritan®PAD 300P Trainer, model TRN-300
The HeartSine PAD 300P Trainer is non-medical device intended to be used for the training of emergency
responders in the proper use of the HeartSine PAD 300P. The Trainer has no therapeutic capabilities and
must not be used in real life rescue situations.
To allow quick and easy identication the HeartSine PAD 300P Trainer incorporates a yellow front user
interface membrane. The HeartSine PAD automated external debrillator has a navy blue/black front
membrane.
The 300P Trainer is intended to be used to train responders who may use the HeartSine PAD 300P
automated external debrillator.
This user manual has been written to include instructions on how to operate the HeartSine PAD 300P
Trainer.
HeartSine recommends that responders who may use one of its debrillators, should be trained in
Cardiopulmonary Resuscitation with debrillator use (CPR-D). The HeartSine PAD Trainer is intended to
be used by approved CPR-D training providers for this purpose.
The HeartSine PAD 300P Trainer is factory congured to operate in accordance with the joint American
Heart Association/European Resuscitation Council 2005 guidelines for CPR. The device comes with 4 pre-
progammed scenarios. The samaritan PAD Trainer can also be manually controlled by the accompanying
remote control.
Should the Guidelines change software will be available to upgrade the PAD 300P Trainer to comply,
please contact your HeartSine authorized distributor or HeartSine Technologies direct.
Once turned on the HeartSine PAD Trainer will play audible voice prompts and accompanying visual
indicators. The Trainer may be controlled with the accompanying remote control included with the device.
Please contact your authorized HeartSine distributor for a list of replacement accessories.

HeartSine PAD 300P Trainer User Manual 3
Warranty Exclusion
HeartSine Technologies or the authorized distributors are not obliged to carry out service/repairs under
warranty if:
a. Unauthorized modications have been made to the device.
b. Non-standard components are used.
c. The user has not used the device in accordance with the indications for use or the instructions pro-
vided in this manual.
d. The serial number of the apparatus is removed, defaced, misused or altered.
e. The device, electrodes or batteries are stored or used operationally outside of environmental speci-
cations.
f. The device has been tested using unapproved methods or inappropriate equipment (see maintenance
section).
Any claims made under warranty must be directed via your distributor from whom the device was origi-
nally purchased. Before carrying out service under warranty, HeartSine Technologies require evidence of
purchase. The product must be used in accordance with the user manual and for the purpose for which it
was intended. If you have a query please contact [email protected] for assistance.
Disposal Instructions
PAD 300P Trainer
The PAD 300P Trainer is a reusable device. If maintained in accordance with the instruction in this
manual it has a warranty period of two years from the date of manufacture. The year of manufacture of
the device is indicated by the rst two digits of the serial number.
Disposal
If you wish to dispose of the PAD 300P Trainer unit, it should be disposed of at an appropriate recycling
facility according to national, state and local requirements. Alternatively return the unit to your local
distributor or HeartSine Technologies for disposal.
Within the European Union
Do not dispose of the PAD 300P Trainer unit as unsorted municipal waste. Collect the PAD 300P Trainer
separately to be reused or recycled in accordance with Directive 2002/96/EEC of the European Parlia-
ment and the Council of the European Union on Waste Electronic and Electrical Equipment (WEEE), or
return to your local distributor or HeartSine Technologies for disposal.
HeartSine samaritan®PAD 300P Trainer, model TRN-300

4 www.heartsine.com
1) Ensure that the HeartSine PAD 300P Trainer is fully charged (see Charging section of this manual).
2) Place the HeartSine PAD 300P Trainer and the trainer Pad-Pak on a at surface. Push the trainer
Pad-Pak into the opening of the HeartSine PAD 300P Trainer and listen for a “click” sound to ensure that
it is properly inserted.
3) Place the batteries supplied with your Trainer into the HeartSine PAD Remote Control.
4) Press the On/Off Button on the HeartSine PAD 300P Trainer and listen to the voice prompts to
ensure that the unit is functioning.
5) If the HeartSine PAD 300P Trainer has insufcient charge, it will not function correctly. Plug charger
into the system to recharge the system. For full instructions see the Charging section of this manual. You
may continue to operate the HeartSine PAD 300P Trainer as it recharges although charging will be at a
reduced rate.
Turning on and off the HeartSine PAD 300P Trainer
To turn on the HeartSine PAD 300P Trainer press the On/Off button on the HeartSine PAD 300P Trainer.
By default the Trainer will function in the last scenario setting used.
To turn off the HeartSine PAD 300P Trainer press the On/Off Button again.
Once the HeartSine PAD 300P Trainer has been turned on, it may be turned off using the accompanying
remote control. To turn the Trainer off press the Off Button (red button) on the remote control.
When turned on the HeartSine PAD 300P Trainer will automatically turn OFF after fteen
minutes if the device is not being used.
Preparing the HeartSine PAD Trainer for use

HeartSine PAD 300P Trainer User Manual 5
On/Off button
Press this button to turn the device
on and off.
Attach pads indicator
The action arrows around this icon
will ash to instruct the user that the
PAD 300P pads should be attached
to the patient as indicated.
Safe to touch indicator
It is safe to touch the patient when
the action arrows around this icon
are ashing. You may perform CPR
or check the patient.
Action arrows
The action arrows around an icon
will ash to indicate the actions that
the user should be performing.
A
B
C
D
E
F
G
H
I
J
Data Port
Status Indicator
Shock Button
Safe To Touch Indicator
Speaker
Pad-Pak Cartridge
On/Off Button
Do Not Touch Indicator
Pads Placement Indicator
Action Arrows
ABC
HE
F
G
D
I
J
HeartSine samaritan®PAD 300P Trainer, model TRN-300
PAD 300P Trainer
Do not touch indicator
Do not touch the patient when the
action arrows around this icon are
ashing. The PAD 300P may be
analysing the patients heart rhythm
or preparing to deliver a shock.
Shock button
Press this button to deliver a
therapeutic shock.

6 www.heartsine.com
Turning off the Trainer
The remote control can be used to turn off the HeartSine PAD 300P Trainer. To turn the
trainer off press the red button on the remote control.
Changing the Volume
There are four volume settings available on the HeartSine PAD 300P Trainer. The volume
control buttons are to the left of the Off Button on the remote control. To increase the
volume press the ‘+’ Button and to decrease the volume press the ‘-’ Button.
Pausing the Trainer
During training the HeartSine PAD 300P Trainer may be paused. To pause the trainer press
the Pause Button ( ||/►). The trainer will remain paused until the Pause Button is pressed
again at which point it will continue to play the scenario selected.
Changing the scenario
The HeartSine PAD 300P Trainer comes with four preprogrammed training scenarios. (For
details on the scenarios see the training scenarios section of this manual). The scenario
may be changed by pressing the appropriate number button on the remote control i.e.
pressing ‘3’ will select training scenario three.
Once the scenario has been changed the device will operate as detailed in the scenarios
section. The device will remain in this scenario until a new scenario is selected.
The remote control
PAD 300P Trainer Remote Control
A
B
C
D
E
F
G
H
Off Button
Volume Control
Low battery indicator
Pause Button
Shock required Scenario
No shock required Scenario
Select Scenario
Attach electrodes
A
B
D
EF
G
H
C

HeartSine PAD 300P Trainer User Manual 7
The remote control
The HeartSine PAD trainer has four preprogrammed training scenarios to choose from. All
preprogrammed scenarios are based on AHA/ERC 2005 guidelines. Details of the four preprogrammed
scenarios are given below.
Scenario 1
1. Setup mode - “Call for Medical assistance”, “Pull green tab”, etc
2. User intervention - “Pads” button to be pressed to conrm electrodes placed
3. Monitor Mode - “Assessing heart rhythm”, “Do not touch the patient”, etc
4. Shock advised - User to press the shock button
5. CPR mode - User to apply CPR with advisory as required
6. Monitor Mode - “Assessing heart rhythm”, “Do not touch the patient”, etc
7. No shock advised
8. CPR mode - User to apply CPR with advisory as required
9. Repeat - Steps 6 to 8 repeated until ‘ON/OFF’ button is pressed
Scenario 2
1. Setup mode - “Call for Medical assistance”, “Pull green tab”, etc
2. User intervention - “Pads” button to be pressed to conrm electrodes placed
3. Monitor Mode - “Assessing heart rhythm”, “Do not touch the patient”, etc
4. No shock advised
5. CPR mode - User to apply CPR with advisory as required
6. Monitor Mode - “Assessing heart rhythm”, “Do not touch the patient”, etc
7. Shock advised - User to press the shock button
8. CPR mode - User to apply CPR with advisory as required
9. Repeat - Steps 6 to 8 repeated until ‘ON/OFF’ button is pressed
Scenario 3
1. Electrodes - Device assumes the electrodes are already attached
2. Monitor Mode - “Assessing heart rhythm”, “Do not touch the patient”, etc
3. Check Pads - “Check Pads”
4. User intervention - “Pads” button to be pressed to conrm electrodes placed
5. Monitor Mode - “Assessing heart rhythm”, “Do not touch the patient”, etc
6. Shock advised - User to press the shock button
7. CPR mode - User to apply CPR with advisory as required
8. Monitor Mode - “Assessing heart rhythm”, “Do not touch the patient”, etc
9. No shock advised
10. CPR mode - User to apply CPR with advisory as required
11. Repeat - Steps 3 to 10 repeated until ‘ON/OFF’ button is pressed
Scenario 4
1. Electrodes - Device assumes electrodes are already attached
2. Monitor Mode - “Assessing heart rhythm”, “Do not touch the patient”, etc
3. Shock advised - User to press the shock button
4. CPR mode - User to apply CPR with advisory as required
5. Monitor Mode - “Assessing heart rhythm”, “Do not touch the patient”, etc
6. Shock advised - User to press the shock button
7. CPR mode - User to apply CPR with advisory as required
8. Monitor Mode - “Assessing heart rhythm”, “Do not touch the patient”, etc
9. No shock advised
10. CPR mode - User to apply CPR with advisory as required
11. Repeat - Steps 5 to 10 repeated until ‘ON/OFF’ button is pressed
Pre - programmed Training Scenarios

8 www.heartsine.com
Manual Control of the HeartSine PAD 300P Trainer
The remote control allows Training providers to control the scenario manually. When turned on the
HeartSine PAD 300P Trainer will operate as detailed in the training scenarios listed. Training providers
can override this by pressing the ‘Shock required’, ‘No Shock required’ or ‘Attach Electrodes’ button.
Shock required.
Pressing the ‘Shock required ‘button will cause the HeartSine PAD 300P Trainer to
override the selected training scenario. Each subsequent analysis period will adivse
a shock to be delivered until either the Trainer is turned off or the ‘No Shock advised’
button on the remote control is pressed.
No Shock required.
Pressing the ‘ No Shock required’ button will cause the HeartSine PAD 300P Trainer
to override the selected training scenario. Each subsequent analysis period will advise
no shock to be delivered until either the Trainer is turned off or the ‘Shock advised’
button on the remote control is pressed.
Attach Electrode Pads.
If the ‘Attach Electrodes’ button is pressed the Trainer will play the attach
the electrodes prompts during the analysis period of operation. The Trainer
will continue to play attach electrode prompts until the ‘Attach Electrodes’
button is pressed again.

HeartSine PAD 300P Trainer User Manual 9
HeartSine PAD 300P Trainer battery management.
The HeartSine PAD 300P Trainer contains a rechargeable battery. It is recommended that you ensure the
HeartSine PAD 300P Trainer is fully charged prior to commencing training activities.
When fully charged the HeartSine PAD 300P Trainer will give you approximately four hours of usage
before it needs to be recharged.
The HeartSine PAD 300P Trainer will monitor the capacity of the battery, as it approaches depletion. Prior
to the battery becoming depleted the Trainer will play the following message.
“Warning. Low battery”
If this warning is heard you may continue to use your HeartSine PAD 300P Trainer for a limited period of
time. If the trainer becomes completely depleted of power it will shut itself down. At this point the Trainer
should be recharged.
If you wish to continue to use the HeartSine PAD 300P Trainer, without recharging it, you may plug the
charger into the device. The device will charge at a much slower rate but the Trainer may continue to be
used.
Recharging the HeartSine PAD 300P Trainer.
To safely recharge the HeartSine PAD 300P Trainer follow the instructions given below.
1) Insert the charger adaptor into the socket on the HeartSine PAD 300P Trainer
as shown in the picture. Ensure the adaptor is fully inserted.
2) Plug the charger into the mains electricity supply.
3) Leave the Trainer to charge. To charge a depleted HeartSine PAD 300P Trainer will take approximately
4 hours.
4) Remove the adaptor from the HeartSine PAD 300P Trainer. Turn on the trainer to ensure that the device
is working.
If the HeartSine PAD 300P Trainer is switched on during charging the charger should be switched off then
on again to restart fast charging.
The HeartSine PAD 300P Trainer must only be charged with the charger supplied with it. Use of any other
charging device will nullify the warranty and may result in damage to the HeartSine PAD 300P Trainer.
The HeartSine PAD 300P Trainer and charger are designed for indoor use only. Do not use in wet or damp
environments.
There are no user serviceable parts inside your HeartSine PAD 300P Trainer, Trainer Pad-Pak or charger.
These products should not be opened. In the unlikely event of a malfunction, please contact your
distributor immediately.
Maintenance

10 www.heartsine.com
Remote Control Batteries
The HeartSine PAD 300P Trainer Remote Control contains a low battery warning indicator. If this
indicator ashes red two times after a button on the remote in pressed it is an indication that the batteries
within the remote need replaced.
The remote control uses standard AAA batteries.
The batteries can be accessed by removing the battery cover at the back of the remote control.
Inserting the batteries into the handheld remote whilst pressing the OFF button will cause the
remote to enter pairing mode and take a new transmission ID. This will be different to that
previously stored on to the trainer device. If this occurs accidentally it will be necessary to
complete the pairing procedure in full to pair the device remote up with the HeartSine PAD 300P
Trainer again.
Normal battery replacement does not cause a problem since pairing is only initiated when the
OFF button is also held down.
HeartSine PAD 300P Trainer Conguration Tool
The HeartSine PAD 300P Trainer conguration tool is software which can be downloaded for free from
the HeartSine website (www.HeartSine.com). This software allows you to upgrade your Trainer. The
following options are available.
Language
The HeartSine PAD 300P Trainer can be reprogrammed to operate with audible prompts in any one of
a selection of languages. Download the current HeartSine PAD 300P Trainer conguration tool user
manual from the HeartSine website for instructions on how to perform this.
Pairing a remote control with the samaritan PAD Trainer
Each HeartSine PAD 300P Trainer has an specic remote control to operate it. This is to allow multiple
devices to be used in close vicinity without interference. In the unlikely event that your remote control no
longer operates with your Trainer it may need to be paired with your Trainer again.
The HeartSine PAD 300P Trainer Conguration Tool can be used to pair a remote with your Trainer. Full
instructions are contained within the accompanying user manual.
Device Identications
Each HeartSine PAD 300P Trainer is given an identication number between 001 and 255 during
manufacture. The remote control for each Trainer is then given the same identication number. In
the unlikely event that two devices with the same ID number are being used at the same time use
the HeartSine PAD 300P Trainer Conguration Tool to assign new numbers to the devices. It will be
necessary to pair the device with its remote control after assigning a new ID number.
Maintenance

HeartSine PAD 300P Trainer User Manual 11
CPR Guidelines 2005
The following is a brief overview of the fundamentals of CPR for lay rescuers as advised by both the American Heart
Association (AHA) and the European Resuscitation Council (ERC) in their 2005 published Guidelines for CPR and ECC. This
is intended only as a quick reference for trained CPR providers. HeartSine recommend that all potential users of the PAD
300P are trained by a competent training organisation in both the use of CPR and PAD 300P, prior to placing a PAD 300P into
service. Should the Guidelines change software will be available to upgrade the PAD 300P to comply, please contact your
HeartSine authorized distributor or HeartSine Technologies direct.
CALL Emergency Services
(999/911/112 etc) Send for an AED
Watch, feel, listen
2 Breaths 30 Compressions
(AHA) / 30 compressions 2
Breaths (ERC)
If available use an AED
Continue CPR until Emergency Services arrive.
Alternate with second person after one cycle or 2
minutes
Person not responsive?
Address person and shake on shoulder
Open the airway, check for breathing
Address person and shake on shoulder
Perform CPR until an AED is available
OR arrival of emergency physician
Engage other people to help you and
alternate CPR
If AED is available switch on and follow
instructions
Analysis shock decision
YES NO
DELIVER SHOCK
Continue CPR for 2 minutes/ 5 cycles

12 www.heartsine.com
Authorized Distributor
English
H017-001-700-0 February 2010
Worldwide Headquarters:
HeartSine Technologies Inc
121 Friends Lane
Suite 400
Newtown, PA 18940
Tel: [phone]
Fax: [phone]
Manufactured by:
HeartSine Technologies Ltd
Canberra House
203 Airport Road West
Belfast BT3 9ED
Northern Ireland
Tel: [phone]
www.heartsine.com
www.heartsine.eu
[email protected]
HeartSine®