Heatmiser PRT-W User manual
Operang Instrucons
Model: PRT-W
REF: PRT-W
Revision 1 11/11
1
%$)$)(
$)*""(%+( @6A
($*(#%)** B6E
%$).&"$ F
#&(*+()&"/ G
**$*#&(*+( G
**$*"%! G
%!$*(#%)** ?>
**$*%#%(*,") ??6?A
#&(*+(%" ?B6?D
%"/*+( ?E
+($$**$$5 ?E
*%(/)* ?F
&*%$"*+(*+& ?G6@D
?
2
$()"")%$'%*'
%+$***(#%)***/","4
$()"")%$
(+""/)&(**(%$*"%*
*(#%)**(%#*!&"*/&"$
)#"""**(#$"(,($*%*)"%*)
%$*%**%#%**(#%)**4
.*!&"**%*-""4"&*(%$*%
**(#%)***%*!&"*4
@
3
$()""$)))'(
@**()()+&&"-***(#%)**4
%))***(/%"(1&+)$
(")*%#&(*#$*%%(9"%*%$
*%**%#%**(#%)**:
$)*""***()$*%"(1%""%-$
*&%"(*/%***()4$&+)*
%"(!$)**(#%)**4
%+)%+"(&"***()$**(#%)**-$*
**(/%$))&"/%$*4$/%+,*!$*
**()%+*%**(#%)**1$)+(/%+(&"***()
-*$?#$+*$%((*%(*$*+(($*"%!)**$4
A
4
Pages 17-24 explain the different features available on this
thermostat.
Pairing with the RC1-W Receiver
If using with the UH1-W wiring centre, turn to page 6.
With the thermostat turned off:
• Press & hold the Clock buon unl you see two sets of
numbers appear.
• The small number 01 in the top right corner of the LCD is the
feature number.
• Press Clock repeatedly unl you see feature 06 (Receiver
Type). The opons within feature 06 are: 00 = UH1-W or
01 = RC1-W receiver.
• Use the Up/Down keys to set feature 06 to 01 (RC1-W).
• Press Clock again unl you see feature 07 (Receiver Address).
You can now select a Receiver Address from 01-32.
• Use the Up/Down keys to set feature 07 to 01. (You should set
a unique receiver address for each receiver installed).
• Press Clock again unl you see feature 08 (Zone number).
5
You are able to connect two PRT-W thermostats to one RC1-W
receiver. You should now use the up/down buons to select
which zone this thermostat controls, 01 or 02.
• Press A to accept, the display will now go blank.
Pairing the thermostat
• On the receiver, press and hold the pairing buon unl the
Comms LED comes on.
• With the thermostat turned off, press & hold the A buon for
5 seconds. The thermostat will send a signal for 1 minute, and
will flash the RF signal icon.
If successful, the Comms LED on the receiver will flash.
• Press the Power Buon once on the thermostat to confirm
pairing.
• If the pairing is unsuccessful, check features 06 to 08 have
been configured correctly, to eliminate a possible signal issue
try to reposion the thermostat closer to the receiver and
repeat the pairing process again.
6
Pairing with the UH1-W Wiring Centre
On the UH1-W wiring centre, take note of the number set on the
rotary switch (Board ID number 1-9). Each UH1-W on the system
will need a different ID number.
With the thermostat turned off:
• Press & hold the Clock buon unl you see two sets of
numbers appear.
• The small number 01 in the top right corner of the LCD is the
feature number.
• Press Clock repeatedly unl you see feature 06 (Receiver
Type). The opons within feature 06 are: 00 = UH1-W or 01 =
RC1-W receiver.
• Use the Up/Down keys to set feature 06 to 00 (UH1-W).
• Press Clock again unl you see feature 07 (UH1-W Board
Address).
7
• Use the Up/Down keys & set the large digits to the board
address of the UH1-W, this is the number set on the UH1-W
rotary switch. (You should set a unique board address on each
UH1-W installed).
• Press Clock again unl you see feature 08 (Zone Number,
01-08). The UH1-W is an 8 zone receiver. Use the up/down
buons to select the zone this thermostat should be linked to.
• Press Clock again unl you see feature 09.
00 = Under-floor heang, 01 = Radiators. Use the up/down
buons to select if the thermostat is controlling Under-Floor
heang or radiators.
• Press A to accept, the display will now go blank.
• Press the power buon once to turn the thermostat back on,
press the up buon & set the target temperature above the
room temperature, the flame symbol should then appear and
the assigned zone on the UH1-W should now be acvated.
This indicates pairing between the thermostat & the UH1-W is
successful.
8
He ng On
He ng Off – Frost Mode
Key Lock
RF Signal Ac ve
Ba ery
Holiday Ac ve
9
#&')*'(&".
%%##&K))*+(($*(%%#*#&(*+(4
)K))**#&(*+(/%+(*(/$*%,$/%+(
%#4
))$)"%!
%)**"%!1%""%-*)*&)"%-4
•***(#%)***+($%$1&())*"%!+**%$
*(*#)
•%+($%-"*%)**%+()+)$*&5%-$
!/)
•())*%&*
•%+($%-"*%)**#$+*)+)$*
&5%-$!/)
•())*%&*
G
10
•%+($%-"*%)**/%*-!+)$*
&5%-$!/)
•())*%)*%($.*
%!$)'#%())
*(#%)**)!/6"%!"*/4%$"1%""%-*)
)*&)2
•())$%"*$%-$!/%(?>)%$)
•%+-"")*"%!)/#%"&&(
•%+$"%!1(&**)*&)%,4
?>
11
Comfort Levels Explained
The Heatmiser PRT-W provides Weekday/Weekend or 7 Day
programming. You should consult the Configuraon Menu
secon to select the required mode.
The thermostat is supplied with comfort levels already
programmed, but these can be changed easily. The default mes
are:
08:00 – 21C (Wake)
09:30 – 16C (Leave)
16:30 – 22C (Return)
23:00 – 17C (Sleep)
If you only want to use 2 levels, you should program the unused
levels to --.––
12
• To
begin programming the comfort levels, press Clock
Once
• If your thermostat is setup for Weekday/Weekend
programming, you will see Mon-Fri shown. For 7 day
programming you will see Monday, you need to use
Up/Down arrow keys to select which day you would
like to program and then press H key to confirm.
• Using the Up/Down arrow keys, enter the required
Wake me
• Press H
• Using the Up/Down arrow keys, enter the required
Wake temperature
• Press H
• You will see Leave
• You should repeat the programming for each period,
entering --.– for unused periods.
• Press A to accept to confirm any changes made.
13
•
•
•
•
•
14
#&')*')
)$*&5%-$((%-!/)""%-)/%+*% +)**)*
*#&(*+(4$/%+&())*(%*)!/)1/%+-"")
*-%($*)(*#&(*+(4
())*%&*4
)$0
(%)*(%**3())$*&%-(+**%$%$-""&"*
*(#%)**$(%)*&(%**#%4$*)#%1**(#%)**
-"")&"/*(%)*%$$-""%$"/*+($**$%$
)%+"*(%%#*#&(*+((%&"%-*)**#&(*+(4
%+"**$*+($%$-")*$(%)*#%1*"#
)/#%"-"")&"/4%$"*(%)*&(%**#%1&())
*&%-(+**%$4
?D
15
•
•
•
The Heatmiser PRT-W has a holiday funcon. This allows you to
16
*(#%)**-"")%-)+*)$*$**(#%)**)
$%"/#%4%$"1(+*%"/+(*%$*%>>
/)4
)%'.()
*(#%)**)*%(/()*+$*%$4)-""()*""
)**$)!*%*(*%(/+"*4%&(%(#*%(/()*1
%""%-*))*&)2
•+($**(#%)**%
•())$%"*%-($&((%-!/+$*"*
&%-()+&4""%*%$)-"")&"/4$
*/,)&&(1**(#%)**)$()*4
?F
17
&)%$")*'(-&"$
)*'892#&')*'%'#)/)+$*%$""%-)/%+*%
)"**-$;5
)*'8:1,)$'$)"3)+$*%$""%-)/%+*%
$()*)-*$($*"%**(#%)**4+"*
)?;-#$)**-*)**#&(*+(%@>;1*
*(#%)**-"")-***$%$*?G;$%*@>;4
*@;($*"1**$-"")-*%$*?F;$%
*@>;
)*'8;2'%()'%))/%+$)*-*(**(#%)**
-""#$*$*(%)**#&(*+(-$**(#%)**)&"/
)*+($%4)+"*1*))$"
?G
18
Feature 04 – Frost Protect Temperature: This is the
temperature maintained when the thermostat is in frost mode.
The range is 07-17°C. The default is 12°C and is suitable for
almost all applicaons.
Feature 05 – Output Delay: To prevent rapid switching, and
output delay can be entered. This can be set from 00-15 minutes.
The default is 00 which means there is no delay.
Feature 06 – UH1-W or RC1-W receiver: The thermostat
can work with our UH1-W 8 zone wiring centre or RC1-W
2 channel receiver. This seng determines which is being used.
Feature 07 – Receiver Address: Within one building, up to 9
UH1-W’s or 32 RC1-W’s can be used. Each receiver must
have a unique receiver address.
Other manuals for PRT-W
1
Table of contents
Other Heatmiser Thermostat manuals
Heatmiser
Heatmiser PRTHW-TS User manual
Heatmiser
Heatmiser PRT-EN1 Slimline Series User manual
Heatmiser
Heatmiser UH8 User manual
Heatmiser
Heatmiser PRT-B User manual
Heatmiser
Heatmiser neoX User manual
Heatmiser
Heatmiser PRT-E User manual
Heatmiser
Heatmiser PRT-WTS User manual
Heatmiser
Heatmiser DT User manual
Heatmiser
Heatmiser PRT-EW User manual
Heatmiser
Heatmiser PRT-UWTS User manual
Heatmiser
Heatmiser Slimline-RF User manual
Heatmiser
Heatmiser TM4-TS User manual
Heatmiser
Heatmiser TM4-TS User manual
Heatmiser
Heatmiser DS-SB User manual
Heatmiser
Heatmiser smartstat User manual
Heatmiser
Heatmiser PRT-ETS User manual
Heatmiser
Heatmiser Senior User manual
Heatmiser
Heatmiser TouchScreen Series User manual
Heatmiser
Heatmiser PRT-WTS User manual
Heatmiser
Heatmiser PRT-EAU1 User manual
