heightec RescuePack WK32 User manual

The heightec Group Ltd, Lake District Business Park, Mint Bridge Road, Kendal, Cumbria, LA9 6NH, UK The heightec Group Ltd, Lake District Business Park, Mint Bridge Road, Kendal, Cumbria, LA9 6NH, UK
Prompt Sheet
WK32 - RescuePackTM
This equipment should only be used by Competent Persons, who have been trained in the use of this specic kit.
These Prompt Sheets are to be read in conjunction with user instructions for each item of the kit.
B
A
c
D E
REF: UI WK32 Issued: 04/02/2021 Revised: 04/02/2021 Approved: SBE
Lowering
1. Select an unquestionably sound anchorage structure,
above casualty.
2. Pass anchor strop (A) around anchorage and connect
karabiner to screwlink.
3. Fit open hook to end of pole. With control device half-
threaded, extend pole to casualty (B). Attach hook to
harness and pull to release, ensuring hook gate closes
fully.
4. Pull rope to casualty tight by pulling tail end through
device (C).
5. Fully thread control-device & lock-o󰀨 by passing tail
rope loop through the screwlink then around device
(D).
6. Check all connections, then cut casualty’s fall arrest
lanyard, with shears.
7. Remove the ‘lock-o󰀨’ and gently lower casualty by
holding tail rope and squeezing device handle into
‘sweet spot’ (E).
REF: UI WK32 Issued: 04/02/2021 Revised: 04/02/2021 Approved: SBE
This equipment should only be used by competent persons, who have been trained in the use of this specic kit.
These user instructions are to be read in conjunction with user instructions for each item of the kit.
Raising
1. Select an unquestionably sound anchorage structure,
above casualty.
2. Pass anchor strop (A) around anchorage and connect
karabiner to screwlink.
3. Fit open hook to end of pole. With control device half-
threaded, extend pole to casualty (B). Attach hook to
harness and pull to release, ensuring hook gate closes
fully.
4. Pull rope to casualty tight by pulling tail end through
device (C).
5. Attach hauling-device to casualty rope as shown (D).
DO NOT PUT DEVICE OVER EDGE
6. To raise casualty, pull tail rope (E).
7. When hauling-device reaches control-device, slide
hauling-device back down rope.
8. Repeat steps 6 & 7 to incrementally raise casualty as
required.
A
c
E
D
Prompt Sheet
WK32 - RescuePackTM
B

The heightec Group Ltd, Lake District Business Park, Mint Bridge Road, Kendal, Cumbria, LA9 6NH, UK
WK32 - Rescue Pack
The heightec Group Ltd, Lake District Business Park, Mint Bridge Road, Kendal, Cumbria, LA9 6NH, UK
REF: AI WK32 Issued: 04/02/2021 Revised: 04/02/2021 Approved: SBE
Disclaimer: It is the users responsibility to assemble the kit correctly referring to individual product user instructions.
User, Kit Assembly Instructions
Assembly
1. Feed rope complete with modied sca󰀨hook attached, into bag. Sca󰀨hook
end at top!
2. Place MSRM pole in bag, attach MSK2 shears + pouch to pole karabiner
with CKA1
3. Thread D011 Quadra on to rope following diagram marked on device/
pictures in le. Quadra should be approx. 10cm from sca󰀨hook end of rope.
Attach screwlink to bottom hole.
4. Attach S25N120P sling to D011 Quadra using screwlink, hand tighten
screwlink. Ensure non sewn end of sling is attached to screwlink.
5. Captivate CKS3 krab to other end of sling (stitched end).
6. Attach D431 Hurricane onto rope – around pulley wheel
(close and latch front plate).
CODE DESCRIPTION
B50 Kari Transport bag 50L
CH01AM Alloy sca󰀨old hook
CKA1 Altair karabiner
CKS3 Astra karabiner
CSN08 Screwlink 8mm
D011 Quadra rescue device Alloy
D431 Hurricane Rescue Hauler
MSK2 Rescue shears with cord and pouch
MSRM RescuePack pole
RS110G Tectra 11mm rope
S25N120P Sling, protected nylon
Kit Contents