Heritage Bathrooms PGRW01L User manual

Granley
Low-Level Cistern Fittings
PGRW01L
Fitting Instructions
& Contents List
Please keep these instructions for future reference and request of
replacement part
(HFI CC00/CC01) (Rev D1)
AFTERCARE INSTRUCTIONS
Your fitting has a high quality finish and should be treated with care to
preserve the visible surfaces.
All surface finishes will wear if not cleaned correctly, the only safe way to clean
your product, is to wipe with a soft damp cloth. Stains can be removed using
washing up liquid. All bath cleaning powders and liquids can damage the
surface of your fitting even the non-scratch cleaners.
GUARANTEE
All products are manufactured to the highest standards and a 10-year
guarantee covers any defect in manufacture.
CONTACT DETAILS
If you require further assistance please contact Heritage Sales and
Technical Enquiries:
Sales: 0844 701 8501
Technical: 0844 701 8503
Email: [email protected]
Website: www.heritagebathrooms.com
Heritage Bathrooms
Unit 6 Albert Road
St Philips Central
Bristol
BS2 0XJ
Before starting any installation project please consider:
Prior to drilling into walls, check there are no hidden electrical
wires, cables or water supply pipes with the aid of an electronic
detector. If you use power tools do not forget:
- Wear eye protection
- Unplug equipment after use
SAFETY
NOTE

Component Pack Fitting Instructions
Please ensure these instructions are followed carefully-if your
unsure about any aspect of the installation,please consult a
qualified installer. In the event of any problem with the function of
this equipment, please check installation before consulting your
supplier.
Do not use mole grips on plastic nuts.
Do not use a sealing compound as damage may occur to plastic
components.
Do not over tighten plastic nuts
Warning
Push the piston assembly from the bottom, inside the housing of
the siphon & remove the tie wrap from the piston rod (shown in
picture’ A’) insert the C-Link into the piston rod as shown in
picture ‘B’.
Feed the lever through the handle hole & secure in place using
back-nut provided, slide the plastic lever arm over the shaft,
ensure the end of the lever arm lines up over the top of the piston,
remove from shaft cut plastic lever arm to suit ( if applicable),
attach onto C- Link, slide back onto shaft & secure in place using
screw. The diagram ‘K’ shows a low level mechanism when
wedges are required, the chrome/gold wedge is to be fitted
externally on the Cistern.
Secure the fulcrum bracket in place using the screw & flat nut
provided, hook the fulcrum arm onto the C-Link & clip the fulcrum
arm into the fulcrum bracket, attach the high level chain & pull.
Final Commissioning
Before turning on the water supply, check all components are free
moving & all joints are correctly made.
Fill the cistern with water & carefully check for leaks.
Test the overflow by holding the float down, ensure that incoming
water is completely discharged, if not partially close the isolation
valve (Not Supplied) & try again, repeat until all incoming water is
discharged.
Check that the inlet valve shuts off on the water line indicated
inside the Cistern. l

Close-Coupled - Plated Kit.
Place the rubber washer over the threads of the siphon as
shown in picture ‘H’ & feed through hole in Cistern, place the
plate over threads of siphon, secure hand tight using back-nut
provided as shown in picture ‘I’ & tighten a further half turn
using a suitable spanner. Picture ‘J’ shows the complete
assembly.
Both methods of closed coupled packs require a close couple
washer between the WC Pan & Cistern as shown in the pictures
above.
Low/High Level
For low/high level packs, place the rubber
washer over the threads of the siphon as
shown in picture ’D’ & feed through hole in
Cistern. Secure hand tight using back-nut
provided as shown in picture ‘E’ & tighten a
further half turn using a suitable spanner. The
flushpipe assembly is shown below (high
level flushpipe not supplied).
When fitting either seal ensure that the
rounded edge on the low level seal & the
bevelled edge on the high level seal are
pointing towards the end of the flushpipe that
is to be inserted into the threads of the
siphon (
).
do not insert more than 40mm into
the tail of the siphon

Hold the swivel arm screw on the
underside of the float arm. Insert the
swivel arm clamp from the top of the
inlet valve arm, tighten to secure in
place, screw the float onto the swivel
arm screw, check for free movement
of the float, (ensure the float does not
get caught on the side/back wall of
cistern). To adjust water level rotate
the water level adjustment screw,
turn clockwise to reduce shut-off
level, turn anti-clockwise to raise
shut-off level, secure by hand
tightening the locking nut.
The inlet valve is fitted with a high
pressure seat (white), if water
pressure is low, the inlet valve is
supplied with low pressure seat (red,
attached to the inlet valve arm) that
can be swapped, diagram ‘N’ shows
the internal assembly of the inlet
valve body.
Assemble the 2 bolts as diagram ‘F’ shows,
feed through respective holes & secure
using the metal washer & nut as picture ‘C
Shows. The complete assembly of the
bolted kit is shown in diagram ‘G’. Place the
rubber washer over the threads of the
siphon as shown in picture ‘D’ & feed
through the hole in Cistern. Secure hand
tight using back-nut provided as shown in
picture ‘E’ & tighten further half turn using a
Suitable spanner.