Heritage Bathrooms TSBC00 Mounting instructions

Models covered:
TSBC00 Basin Taps
TSBC01 Bath Taps
Please keep this booklet for future reference.
Installer: when you have read these
instructions please ensure you leave them
with the user.
Somersby Tap Range
Installation Instructions
and User Guide
www.divapor.com

Contents
When you buy a Heritage product, you can be confident that it not only features a beautiful,
distinctive, classic design, but that it has also been made to the very highest quality standards.
To ensure that it works to its full potential, it needs to be fitted correctly.
These fitting instructions have been created to give you all of the information you need and,
if you need any further help, please do not hesitate to give us a call on 0844 701 8503.
01
Important Safety Information 02
General Specifications 02
Dimensions 03
Installation 04
Maintenance 05-06
Map of Hard Water Regions 07
Troubleshooting 08
Guarantee 09-10
www.divapor.com

Before starting any installation project please consider the following:
•Prior to drilling into walls, check there are no hidden electrical wires or cables or water supply
pipes with the aid of an electrical detector.
•If you use power tools do not forget:
- Wear eye protection.
- Unplug equipment after use.
•This product must not be modified in any way as this will invalidate the guarantee.
•These fittings need to be installed in accordance with and meet the requirements of the Water
Supply (Water Fittings) Regulations 1999 and Scottish Byelaws 2004.
Safety Note
•Please read these instructions & retain for future use. All products manufactured & supplied
by Heritage are safe, provided they are installed correctly, used correctly, and receive regular
maintenance in accordance with these instructions.
•If you are in any doubt about your ability to install this product safely you must employ
the services of an experienced, qualified plumber.
02
General Specifications
Operating pressure range (bar) Min Max
Basin Taps 0.2 5.0
Bath Taps 0.2 5.0
Maximum static pressure – 10.0 bar
NOTE:- Nominally equal (balanced) inlet supply pressures are recommended for optimum
Performance of mixer taps.
Designed to comply with BS EN 200 for single taps / combination taps for water systems of type 1 and
2 general technical specifications; and to be used within systems designed to BS 6700.
BS 6700 recommends the temperature of stored water should never exceed 65°C.A stored water
temperature of 60°C is considered sufficient to meet all nominal requirements and will minimise
the build up of lime scale in hard water areas.
www.divapor.com

Dimensions
03
Basin Taps (TBC00)
Bath Taps (TBC01)
75
100
G1/2”
56
33
116
103
153
90
112
63
G3/4”
38
66
www.divapor.com

Installation
1. Indice x2
2. Handle Screw x2
3. Lever Handle x2
4. Spline Adapter x2
5. Valve x2
6. Tap Body x2
7. Plinth x3
8. Rubber ‘O’ Ring x3
9. Rubber Washer x3
10. Backnut x2
11. Locking Pin x2
12. Anti-Splash x2
1. Identify all components are present prior to starting installation.
2. Ensure that the rubber ‘O’ ring (8) is fitted to the underside of the plinth (7); slide onto the
threaded tail and install the taps to the basin.
3. Using the washer (9) and backnut (10) secure the taps to the basin by tightening the backnut on
the underside of the basin.A suitable spanner may be required to fully tighten the backnut (10)
and secure the tap into the desired position.
4. Connect the hot and cold water supplies to the taps.
5. Turn on the water supplies and open both taps letting the water flow for a few minutes to
check all joints and connections for any leaks.
04
1
2
3
4
5
6
7
8
9
10
12
11
www.divapor.com

General Cleaning
Your fitting has a high quality finish and should be treated with care to preserve the visible
surfaces.All finishes will wear if not cleaned correctly.The only safe way to clean your product is
to wipe with a soft damp cloth. Stains can be removed using washing up liquid.All bathroom
cleaning products (powders and liquids) will damage the surface of your fitting, even the non-
scratch cleaners.
Note: Never use abrasive detergents or disinfectants or those containing alcohol, hydrochloric
acid or phosphoric acid.
See map of Hard Water Regions on page 07 to see the water type in your area
Maintenance
05
www.divapor.com

Maintenance cont.
We advise that your fitting is regularly serviced in
hard water areas to maintain optimum
performance; see map of Hard Water Regions on
page 07.
If your fitting begins to leak the following should
be carried out;
Isolate both hot and cold water supplies to the
tap by either:
•Turning the water supply off at the mains
stopcock or
•Turning off the isolation valves to the tap.
1. Remove the indice at the top of the handle
to reveal the concealed screw.
2. Remove the screw and pull the handle
upwards from the spline adapter and valve.
3. Using a suitable spanner remove the valve
from the tap body.
4. Clean the valve and the seating inside the tap
body.
5. If necessary replace the valve.
Please visit www.heritagebathrooms.com in
order to find spare parts for this product.
6. Replace the valve into the tap body and
tighten fully using a suitable spanner.
7. Re-connect handle assembly.
8. Turn on water supply and check for leaks.
9. Contact our helpline should if problem
persists.
Cleaning the Valves Within The Side Bodies
Spline Adapter
Valve
Ta p B o d y
Handle
Indice
Screw
06
www.divapor.com

Hard to very hard
Above 200mg/l as
calcium carbonate
equivalent
Soft to
moderately soft
0 - 100mg/l as
calcium carbonate
equivalent
Slightly hard to
moderately hard
100 - 200mg/l as
calcium carbonate
equivalent
Map of Hard Water Regions
07
www.divapor.com

Symptom Cause Remedy
No flow or poor flow rate. Partially closed stop or service valve in
water supply pipework to the tap.
Open stop or service valve.
Head of water is below the minimum
distance required.
Refer to the Specification section for
minimum pressures required.
Possible airlock / blockage in supply
pipework
Remove water supplies from the fitting
and flush the system to remove any
airlocks / debris.
Cartridge / Valve not opening fully. Service fitting. Refer to maintenance
section on page 5-6.
Water dripping for a few
seconds after the tap has
been turned off.
This is caused by ‘capillary action’ and
residual water in the spout being
siphoned out. This should only last for a
couple of seconds.
Constant dripping / leaking
when the tap is not in use.
Cartridge / Valve not fully shutting off. Service fitting and replace cartridge /
valve. Refer to maintenance section on
page 5-6.
Fitting does not turn on. Water supplies not turned on. Check that the water supplies to the
fitting are turned on.
Closed stop or service valve. Open stop or service valve.
Water does not come out
of the showerhead when
using the bath shower
mixer.
Diverter mechanism not fully open. Open the diverter mechanism fully by
pulling the diverter knob up.
Insufficient water pressure / header
height.
Refer to the specification section for
minimum pressures required.
Troubleshooting
08
www.divapor.com

Heritage Bathrooms Guarantee
When you buy a Heritage product, you can be confident that it not only features distinctive design, but that
it has also been made to meet our rigorous quality standards.
We offer robust guarantees and an attentive aftercare service to ensure that if you do experience any
issues, we can deal with a problem quickly, and effectively.
Please note that guarantees are only valid with proof of purchase.
Our guarantees are as follows:
Register now for additional peace of mind
Register your product with us now and, if you do have any queries after installation, we’ll be able to quickly
identify the product and give you the best advice. It also means that you won’t have to keep your proof of
purchase to validate your guarantee. To register, simply go online at www.heritagebathrooms.com/register
GuaranteeTerms and Conditions
This guarantee is in addition to your statutory and other legal rights and is subject to the following
conditions:
The product was purchased within the United Kingdom or Republic of Ireland
The product is used in domestic applications only
The guarantee applies solely to the original purchaser with proof of purchase
The installation must allow ready access to all products for the purpose of inspection, maintenance or
replacement
Repair under this guarantee does not extend the original expiry date. The guarantee on any
replacement parts or product ends at the original expiry date
Any part found to be defective during the guarantee period will be replaced without charge, providing that
the product has been installed in accordance with the instructions given in this guide and used as the
manufacturer intended. If the product is no longer available, Heritage will endeavour to provide the nearest
equivalent.
2 Years on
Mirrors &
WC Seats
5 Years on
Bath Screens,
Furniture,
Shower Valves,
Taps, Wastes
& Accessories
Lifetime Guarantee
on Acrylic &
Cast Iron Baths
And Sanitaryware
09
www.divapor.com

Heritage Bathrooms Guarantee Cont.
The guarantee does not cover:
Damage or defects caused by
‐General wear and tear (including special non-chrome finishes; components such as filters, seals,
‘O’ rings and washers)
‐Incorrect installation
‐Repair using non-Heritage parts
‐Accidental or wilful misuse
‐Corrosion and the use of inappropriate cleaning products.
‐System debris including the build-up of limescale (which can be controlled through regular
servicing and maintenance)
Compensation for loss of use of the product or consequential loss of any kind.
In the interests of continuous product improvement, Heritage reserves the right to alter product
specifications without notice.
Need help?
In the unlikely event that you encounter a problem with your Heritage product, you must, in the first
instance, contact the retailer you purchased it from. They will advise as to whether it is due to a
manufacturing fault or an installation fault. If the problem is due to a manufacturing fault, they will contact
us to arrange a supply of a replacement product as soon as possible. To speak to a Heritage customer
service advisor, please contact our technical helpline on 0844 701 8503.
10
www.divapor.com

Heritage Bathrooms
Birch Coppice Business Park
Dordon
Ta m w o r t h
B78 1SG
Website: www.heritagebathrooms.com
Telephone: [phone]
Email: [e-mail]
HFI (SOMERSBY – BAS/BATH) REV. D1
www.divapor.com