Heritage Bathrooms TDCC00 Mounting instructions

Models covered:
Basin Taps
TDCC00 / TDCG00 / TDCN00
Short Nose Basin Taps
TDCCS00 / TDCGS00/TDCNS00
Bath Taps
TDCC01 / TDCG01/ TDCN01
Bath Filler
TDCC072 / TDCG072/TDCN07
Bath Shower Mixer
TDCC02 / TDCG02/ TDCN02
Please keep this booklet for future reference.
Installer: when you have read these instructions please
ensure you leave them with the user.
Dawlish Tap Range
Installation Instructions
and User Guide

Contents
When you buy a Heritage product, you can be confident that it not only features a beautiful,
distinctive, classic design, but that it has also been made to the very highest quality standards.
To ensure that it works to its full potential, it needs to be fitted correctly.
These fitting instructions have been created to give you all of the information you need and,
if you need any further help, please do not hesitate to give us a call on 0330 026 8503.
01
Important Safety Information 02
General Specifications 02
Dimensions 03-04
Installation 05-07
Basin Taps & Bath Taps 05
Bath Filler / Bath Shower Mixer 06-07
Maintenance 08-09
Troubleshooting 10
Guarantee 11
Notes 12-14

Before starting any installation project please consider the following:
•Prior to drilling into walls, check there are no hidden electrical wires or cables or water supply pipes with the
aid of an electrical detector.
•If you use power tools do not forget:
-Wear eye protection.
-Unplug equipment after use.
•This product must not be modified in any way as this will invalidate the guarantee.
•These fittings need to be installed in accordance with and meet the requirements of the Water Supply
(Water Fittings) Regulations 1999 and Scottish Byelaws 2004.
Safety Note
•Please read these instructions & retain for future use. All products manufactured & supplied
by Heritage are safe, provided they are installed correctly, used correctly, and receive regular
maintenance in accordance with these instructions.
•If you are in any doubt about your ability to install this product safely you must employ
the services of an experienced, qualified plumber.
02
General Specifications
Operating pressure range (bar) Min Max
½” Basin Taps 0.1 5.0
¾” Bath Taps 0.2 5.0
Bath Filler 0.2 5.0
Bath Shower Mixer 0.2 5.0
Maximum Static Pressure –10.0 bar
NOTE:-Nominally equal (balanced) inlet supply pressures are recommended for optimum
Performance of mixer taps.
All products manufactured and supplied by Heritage Bathrooms are safe to use provided that they are installed,
operated and receive regular maintenance in accordance with these instructions. This product needs to be installed in
accordance with, and meet the requirements of the Water Supply (Water Fittings) Regulations 1999 and current by-
laws. For full Installation Requirements & Notes (IRN) please visit wras.co.uk/directory.
Isolation valves must be fitted to the inlet water supplies to ensure ease of future maintenance. Before installing this
product the water supply must be thoroughly flushed in order to remove any swarf, solder etc. This product must
not be modified in any way as this will invalidate the guarantee. Full access must be made available for future
maintenance/servicing purposes. If in doubt, contact a registered plumber or your Local Water Authority or the
Secretary of the Institute of Plumbing, address as follows:-
The Institute of Plumbing,
64 Station Lane,
Hornchurch,
Essex,
RM12 6NB,
Tel: [phone]

Basin Taps (TDCC00/TDCG00/TDCN00)
Short Nose Basin Taps
(TDCCS00/TDCGS00/TDCNS00)
Bath Taps (TDCC01/TDCG01/TDCN01)
Dimensions
03

04
Bath Filler (TDCC072/TDCG072/TDCN07)
Bath Shower Mixer (TDCC02/TDCG02/TDCN02)
Dimensions Cont.

8*
Installation –Basin / BathTaps
1. Identify all components are present prior to starting installation.
2. Using the washer (10) and backnuts (11) secure the taps to the basin by tightening the backnuts
onto the pre-fitted threaded tails (9).A suitable spanner may be required to fully tighten the
backnuts (11).
3. Connect the hot and cold water supplies to the
connecting pipes
4. Turn on the water and fully open the mixer,
allowing it to run for a few minutes and check
all joints and connections for any leaks.
2
1. Indice x2
2. Handle Screw x2
3. Metal Washer x2
4. Handle x2
5. Shroud x2
6. Valve x2
7. Washer x2
8. Tap Body* x2
9. Threaded Tail x2
10. Washer x2
11. Backnut x2
6
1
3
4
5
7
9
10
11
*Tap body shown is for illustration purposes only. The
installation process applies to all models listed for this
booklet
05

8
Installation –Bath Filler / Bath Shower Mixer
2
1. Handset x1
2. Hose x1
3. Cradle Assembly x1
4. Diverter Assembly x1
5. Elbow Assembly x2
6. Pillar Assembly x2
6
1
3
4
7
9
10
11
5
12
7. Washer x2
8. Backnut x2
9. Handset Holder x1
10. Screw x1
11. Shroud x1
12. Rawl Plug x1
06

Installation –Bath Filler / Bath Shower Mixer Cont.
* Bath shower mixer only
1. Identify all components are present prior to starting installation.
2. Connect the elbow assembly (5) to the tap body, then connect the pillar assembley (6) to the
elbow (5).
3. Using the washer (7) and backnuts (8) secure the pillars to the bath by tightening the backnuts
onto the pre-fitted threaded tails.A suitable spanner may be required to fully tighten the
backnuts (8).
4. * Attach the cradle assembly (3) to the tap body, again ensuring the washers are correctly
placed.
5. * Fit the handset (1) to the shower hose (2) and connect the hose to the outlet on the cradle.
6. Connect the hot and cold water supplies.
7. Turn on the water and fully open the mixer, allowing it to run for a few minutes and check all
joints and connections for any leaks.
8. * To fit the wall bracket, ensure firstly that the position will allow the handset to comfortably
reach it when attached to the 1.5m hose. Mark out and drill the hole to suit the rawl plug (12).
Using the screw (10), fit the shroud (11) to the wall and assemble the remaining components as
shown in the diagram.
Wall Mount Installation
To wall mount this product, unscrew the elbows from the body and screw the legs directly into the
rear inlets of the tap body.
NOTE: This will alter how far out the product will sit proud of the wall. Care must be taken
when attaching the product, Please do not place weight on this product when fitting
as a wall mounted option.
07

General Cleaning
Heritage products are made from premium materials, with hand polishing, PVD, EPD and
electroplated finishes.
Your product should be regularly cleaned with warm water, a mild pH-neutral liquid soap, and
polished with a soft cloth.Any residues from soap, toiletries etc. should be rinsed off straight
after use.
Household bleaches and cleaners contain harsh chemicals and may damage the surface finish.
Avoid using abrasive cloths, scouring pads, scrub sponges, steel wool or anything similar.
Some surfaces such as nickel and pewter may be affected by the dye found in some cloths, so it
is also important to avoid leaving cloths on surfaces.
We advise that your fitting is regularly serviced in hard water areas to maintain optimum
performance.
Cleaning the Showerhead -Bath Shower Mixer
The hardness of the water in your area will determine how often you should clean your
showerhead. Build up of scale in particularly hard water areas combined with constant use
means you may need to clean your shower head once a week.To ensure continued performance
the shower head needs to be regularly de-scaled. If de-scaling products are used, rinse
thoroughly with clean water after use to prevent damage.
Maintenance
08

Maintenance Cont.
If your fitting begins to leak the following should be
carried out;
Isolate both hot and cold water supplies to the tap
by either:
•Turning the water supply off at the mains
stopcock or
•Turning off the isolation valves to the tap.
1. Unscrew the indice, to reveal the screw and
washer and proceed to remove these with a
suitable screwdriver.
2. Remove the handle and unscrew the shroud.
3. Using a suitable spanner remove the valve.
4. Replace the valves. Please visit
www.heritagebathrooms.com in order to find
spare parts for this product
5. Place the valve into the tap body, ensuring the
washer is in the required position, and tighten
the valve fully using a suitable spanner.
6. Re-connect the shroud, handle and all other
components.
7. Turn on water supply and check for leaks.
9. Contact our helpline should if problem persists.
Replacing the Valves
Handle
Indice
Tap Body
Shroud
Washer
Valve
Screw
&
Washer
Handle
Indice
Shroud
Screw & Washer
Valve
Washer
Tap Body
09

Troubleshooting
Symptom Cause Remedy
No flow or poor flow rate. Partially closed isolation valve. Open isolation valve.
Instantaneous water heater cycles on
and off as flow rate or pressure is too
low.
Increase water flow rate or pressure
through system.
Head of water is below the
minimum distance required.
Refer to specification for minimum
distance required.
Hot or cold water being drawn off
elsewhere causing pressure changes or
instantaneous boiler temperature
changes.
Do not use other water outlets when
using the taps.
Airlock or partial blockage in the supply
pipework.
Flush through pipework to ensure
removal of debris and any airlocks.
Airlock or partial blockage in the supply
pipework.
Water dripping for a few
seconds after the tap has
been turned off.
This is normal for a short time after
using the taps.
This is caused by residual water
tension, the build up of water in the tap
body
If water continues to drip, possibly due
to the ceramic disc valves.
Remove valves and clean, refer to
'Maintenance'
section before starting any
maintenance.
Constant dripping / leaking
when the tap is not in use.
Cartridge / Valve not fully shutting off. Service fitting and replace cartridge /
valve. Refer to maintenance section on
page 06.
Fitting does not turn on. Closed isolation valve. Open isolation valve.
Closed stop or service valve. Open stop or service valve.
Water does not come out
of the showerhead when
using the bath shower
mixer.
Diverter mechanism not fully open. Open the diverter mechanism fully.
Mains water supply turned off. Turn on mains water supply.
10

Heritage Bathrooms Guarantee
The confidence we have in the quality of our products and services enables us to offer a free
peace-of-mind product guarantee from 2years up to alifetime guarantee against any manufacturing
faults, with proof of purchase. In addition, our attentive customer service team are available to
help solve any problems which may arise quickly and effectively so you can enjoy your bathroom.
To see the specific guarantee for this product, scan the QR Code
or visit the following URL:
https://www.heritagebathrooms.com/service-centre/guarantee
G UARANTEE
11

Notes
Please use this space to add any notes which you or your installer may have regarding the plumbing,
installation, and/or servicing of this product:
12

Notes
Please use this space to add any notes which you or your installer may have regarding the plumbing,
installation, and/or servicing of this product:
13

Notes
Please use this space to add any notes which you or your installer may have regarding the plumbing,
installation, and/or servicing of this product:
14

We love to see how Heritage products are used so please keep in
touch and share pictures of your new bathroom with us.
If you have any queries, our dedicated customer service teams and
products experts are available to help.
Email us [e-mail]
Call us 0330 026 8503
Website www.heritagebathrooms.com
UK: Heritage Bathrooms, Pooley Hall Drive, Birch Coppice Business Park, Dordon,
Ta m w o r t h B78 1SG
EU: Masco Europe S.à.r.l., 14 Rue Strachen, 6933 Mensdorf, Luxembourg.
@heritagebathrooms
D3