HiB 33400 User manual

Cyclone Fans
Cyclone Chrome Non-Illuminated
Art no.: 33400
Cyclone White Non-Illuminated
Art no.: 33300
Cyclone White Illuminated
Cool White Art no.: 32600
Warm White Art no.: 33800
Cyclone Chrome Illuminated
Cool White Art no.: 32700
Warm White Art no.: 33700
Components
1x Fascia
1x LED Driver - (for illuminated products only)
1x High powered Inline Fan
1x 3 metre flexible ducting
1x Brown external fixed grille
4x Galvanized steel hose clamps
1x Screw and dowels pack
1x Plastic Screwdriver
1x Fitting instructions
All installations must comply with guidelines which are based on a zonal concept Fig.1. This concept must be fol-
lowed to ensure the safe installation. These regulations apply to domestic installations only. Installations must be
made in accordance with the current IEE wiring regulations and relevant building regulations.
Thank you for purchasing this HiB product. We recommend that all electrical bathroom products should only be
fitted by a suitably qualified, Part P registered electrician.
Suitable for installation in zones: 2 & outside zones
Fig.1
Electrical safety information - Ensure mains power supply is
switched off before starting installation. Before drilling, ensure
there are no hidden cables or pipes in the wall.
Please retain this leaflet for future reference. R210728 Ver No. 1.0 Jan 2019

Mounting Fascia
Mounting Fan Unit
1. The ventilation should be ducted through the roof space, ducting to an external soffit under the eaves or
grille in the slope of your roof. Ducting can only run between joists, not across them.
2. Mark the position of the fascia with a pencil in a suitable posistion on the ceiling, making sure that it is
between joists.
3. Drill a 9mm hole through the ceiling along the edge of the pencil line. Now cut out the hole with a pad
saw.
4. Hold the fascia against the ceiling and mark the posistion of the fixing holes, fix the unit in place using suit-
able fixings - (not supplied)
5. Attach the flexible ducting with the metal hose clamps. Ensure the ducting has a smooth flow towards the
motor body. Follow a simular procedure for the outside wall grille. Extra ducting may be used to extend the
distance to the external grille but the performance will be reduced.
Install the Cyclone Inline fan within the lo or ceiling space, ensuring the correct direction of air flow using
the arrows on the fan. DO NOT COVER the motor or LED driver with lo insulation. The fan is only suitable for
horizontal mounting on a wall or floor. See fig A and fig B.Follow the visual aids below to mount the Fan unit.
Do not run the ducting over the joists, this will cause a build of condensation and reduce the
extraction rate. Ensure the ducting is run between joists to create smooth airflow.
min 1m
g. A horizontal on a wall g. B horizontal on a oor Do not mount duct or
motor vertically

Electrical Connection
Ensure the mains power supply to which the fan is being connected to is turned off. This product is designed
to be connected to an on/off switch outside the bathroom, or to a celing mounted pull cord switch. Please
follow the visual aids below for wiring the fan.
Once the cover has been taken off
then you can Install the fan wires
into the terminals. The fan should
be wired as follows:
N= Black or Blue L= Brown LT=
Grey .
See image le.
Alternatively if you only have a
two core cable, you can wire the
fan up as follows:
N= Black or Blue L= Brown now
you can loop from the L to the LT.
This does bypass the timer func-
tion. The fan will now only oper-
ate as an on/off fan.
See image le.
L1 L2
C
LT L1LN
NL
LOOP
Power Supply
Wall Switch
C
e
i
l
i
n
g
R
o
s
e
Fan
Earth connection has
been removed for
illustration purposes only
LT L1LN
Fan
L1 L2
C
NL
LOOP
Power Supply
Wall Switch
C
e
i
l
i
n
g
R
o
s
e
Earth connection has
been removed for
illustration purposes only
1. 2. 3.

©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try and make sure they are as accurate as possible. In the interest of continuous
product development, HiB reserves the right to alter specifications as necessary. E & OE.
T: [phone] F: [phone] E: [e-mail] hib.co.uk
Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN
Maintenance
In order to maintain the safe and effective operation of the fan regular maintenance must be performed
Fan maintenance is to be performed only aer the fan is disconnected from the mains power supply.
This includes periodic cleaning of the surface of dust and dirt.
All surfaces should be cleaned with a diluted detergent and a so cloth. Avoid water dripping on the electric
components. Wipe the surfaces dry aer cleaning.
Aercare service - In the unlikely event that this product should fail, please contact HiB customer services.
The details are shown below.
WEEE compliance
Must not be mixed with
general household
waste
Timer System
Wiring diagram for lamp
The timer circuit is under mains Voltage. Ensure mains power supply is switched off before making
any adjustments.
The fan is operated by turning on the wall
switch. When the switch is turned off the fan
will continue to operate within the set perios
of time. Adjustable between 2-30mins. This
can be adjusted by turning the potentionme-
ter T clockwise to increase and anticlockwise
to decrease the run time.
Cool White and Warm White illuminated fans.
ONLY
use the
screwdriver
provided
to adjust
the timer
setting.
AC in DC out
Live is RedLive supply is Red or Brown
Neutral supply is Blue or Black Neutral is Black