HiB SELV Hush Chrome User manual

FI #05 005 R161206 Ver No. 1.1 Jan 2017
SELV Hush & SELV Breeze Wall Mounted Fans
Thank you for purchasing this HiB product.
Please read through these instructions carefully and refer back to them during
installation to ensure that your product is fitted safely and that it retains its high
quality finish.
Please retain this leaflet for future reference.
Before drilling, ensure there are no hidden cables or pipes in the wall.
Please see Fig. 1 on the back page for details
Suitable for installation in zones:1,2 & Outside Zones
SELV Breeze Chrome
Art no. 34800
SELV Breeze White
Art no. 34700
SELV Hush Chrome
Art no. 34600
SELV Hush White
Art no. 34500

2
Fitting
1) Choose a suitable position for your fan
according to Figure 1 on the back page. Use
a cable finder to check if there are any buried
cables or pipes in the wall or ceiling. Draw
around the outside of the fan with a pencil to
determine its exact position.
2) Make a suitable sized hole in the wall/ceiling
with the appropriate tools.
N.B. If wall mounted ensure the hole is angled
slightly downward to stop any moisture
running back into the motor.
If mounted in the ceiling ensure the hole is
between the joists.
3) Fit flexible ducting into the hole, flush with
both sides of the wall. Ensure the duct slopes
slightly downwards towards the outside.
Make good any plasterwork around the duct.
4) Position the fan back into place, and mark the
four fixing points. Drill the required holes in
the marked positions. If drilling through tile,
use a ceramic drill bit. Insert wall plugs into
the drilled holes.
5) Follow a similar procedure for the outside wall
grille.
6) If ceiling mounted the ducting should be
routed to the nearest soffit.
Technical Information
Power input: Breeze & Hush - 230v (must be
connected to 12v transformer supplied)
Maximum ventilation volume: Breeze - 77m3/h
Hush - 86m3/h
Power consumption: Breeze - 14w
. Hush - 7.5w
Dimensions: Breeze - W152 x H152 x D126mm h
. Hush - W158 x H158 x D107mm
Electrical Connection
1
4
5
2
3
Please ensure that the fan unit is positioned in
accordance with the diagram below i.e. With
the electrical access point (5) top le.
1
2
4
3
1 Holes for fan mounting (x4)
2 Terminal block
3 Electrical access points
4 Wire fixing rack
Breeze
1 Casing
2 Fan propeller
3 Function module
4 Protective cover of terminal block
5 Electrical access point
Fascia removal
Hush - Depress plastic nodule on the side of the
fascia and gently prise away from the casing.
Breeze - In order to remove the fascia for
maintenance, please remove the small retaining
screw and gently prise the fascia away from the
casing.
Hush

hib.co.uk 3
1) Ensure the domestic electrical mains supply to
which the fan is being connected is turned off.
This product is designed to be connected to
an on/off switch outside the bathroom, or to a
ceiling mounted pull cord switch.
2) Hush Only: Remove the front panel and
protective cover (4). Pass the power wire
through the hole in the rubber plug (beneath
protective cover) at the fan casing flange.
3) Breeze Only: Remove the protective grille.
Cut out blanking plug of electrical access
point (3) and lead the power supply cords
through the hole.
4) Make the electric connections according to
the relevant wiring diagram below.
5. Connect the electrical wiring to the motor
according to the diagram below.
- Switching fan and luminaire on/off
together with one switch.
6. Fix the fan to the wall/ceiling using 4
screws.
7. Replace the cover and protective grille.
Maintenance
In the event of a fault, please check the in-line
fuse located inside the connection box.
Fan maintenance is to be performed only aer
the fan is disconnected from the mains power
supply. Maintenance means periodic clearing
of the surfaces from dust and dirt.
In order to remove the fascia for maintenance,
please remove the small retaining screw and
gently prise the fascia away from the casing.
(SELV BREEZE ONLY).
Electrical Connection
+
-N
L
230v
SupplyTransformerFan
Ceiling mounted...
For ceiling mounting follow procedure for wall
mounting making sure ducting isn’t mounted
vertically to the outside. This is to ensure
moisture doesn’t come back into the motor.
Do not
mount vertically

These products are suitable for installation in zones: 1,2 &Outside Zones
All installations must comply with guidelines which are based on a zonal concept. The diagram above
illustrates this concept and must be followed to ensure the safe installation of electrical appliances in
the bathroom. These regulations apply to domestic installations only. Installations must be made in
accordance with the current IEE wiring regulations and relevant building regulations. HiB recommends
that all electrical bathroom products should only be fitted by a suitably qualified, Part P registered
electrician.
©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try and
make sure they are as accurate as possible. In the interest of continuous product development, HiB reserves the right to alter specifications as necessary. E & OE.
T: [phone] F: [phone] E: [e-mail] hib.co.uk
Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN
(Fig 1)
Electrical Safety Information
Ensure mains power supply is switched off before starting installation. Before
drilling, ensure there are no hidden cables or pipes in the wall.
Care Instructions
All surfaces should be cleaned with diluted detergent (i.e. washing up liquid) and
a so cloth. Do not use abrasives or solvents when cleaning this product.
Wipe off all water spillages as soon as possible using a so, damp cloth.
Aercare Service
In the unlikely event that this product should fail please contact HiB customer
services, details shown below.
WEEE compliance
Must not be mixed with general household waste