HiB 33600 User manual

Turbo Fans
Turbo Chrome Non-Illuminated
Art no.: 33600
Turbo White Non-Illuminated
Art no.: 33500
Turbo White Illuminated
Cool White Art no.: 32200
Warm White Art no.: 34000
Turbo Chrome Illuminated
Cool White Art no.: 32300
Warm White Art no.: 33900
Components
1x Fascia.
1x LED Driver - (for illuminated products only)
1x High powered Inline Fan
1x 3 metre flexible ducting
1x White external fixed grille
4x Galvanized steel hose clamps
1x Screw and dowels pack
1x Plastic Screwdriver
1x Fitting instructions
1x Foam strip.
All installations must comply with guidelines which are based on a zonal concept Fig.1. This concept must be fol-
lowed to ensure the safe installation. These regulations apply to domestic installations only. Installations must be
made in accordance with the current IEE wiring regulations and relevant building regulations.
Thank you for purchasing this HiB product. We recommend that all electrical bathroom products should only be
fitted by a suitably qualified, Part P registered electrician.
Suitable for installation in zones: 2 & outside zones
Fig.1
Electrical safety information- Ensure mains power supply is switched off
before starting installation. Before drilling, ensure there are no hidden
cables or pipes in the wall. The Turbo illuminated Inline Fans are supplied
with a 5 Watt LED Lamp. DO NOT replace with any other lamp as this will
invalidate any warranty. DO NOT exceed the stated wattage.
Please retain this leaflet for future reference. R211007 Ver No. 1.0 Oct 2021
Please note:
Once the fan is powered this may turn on straight away. This is because the fan has a capacitor and holds an initial charge.

Mounting Fascia
Mounting Fan Unit
1. The ventilation should be ducted through the roof space, ducting to an external soffit under the eaves or
grille in the slope of your roof. Ducting can only run between joists, not across them.
2. Mark the position of the fascia with a pencil in a suitable posistion on the ceiling, making sure that it is
between joists.
3. Drill a 9mm hole through the ceiling along the edge of the pencil line. Now cut out the hole with a pad
saw.
4. Hold the fascia against the ceiling and mark the posistion of the fixing holes, fix the unit in place using
suitable fixings- (not supplied)
5. Attach the flexible ducting with the metal hose clamps. Ensure the ducting has a smooth flow towards the
motor body. Follow a simular procedure for the outside wall grille. Extra ducting may be used to extend
the distance to the external grille but the performance will be reduced.
Install the Turbo Inline fan within the lo or ceiling space, DO NOT COVER the motor or LED driver with lo
insulation. The fan is only suitable for horizontal mounting on a wall or floor. Follow the visual aids below to
mount the Fan unit.
Do not run the ducting over the joists, this will cause a build of condensation and reduce the extraction rate.
Ensure the ducting is run between joists to create smooth airflow.
min 1m
g. A horizontal on a wall g. B horizontal on a oor Do not mount vertically

Electrical Connection
Ensure the mains power supply to which the fan is being connected to is turned off. This product is designed
to be connected to an on/off switch outside the bathroom, or to a celing mounted pull cord switch.
Once the cover has been
taken off then you can
Install the fan wires into the
terminals. The fan should
be wired as follows:
N= Black or Blue L= Brown
LT= Grey
See image le.
Alternatively if you only
have a two core cable, you
can wire the fan up as
follows:
N= Black or Blue L= Brown
now you can loop from the L
to the LT.
This does bypass the timer
function. The fan will now
only operate as an on/off
fan.
See image le.
Bridge L, LT Only if permanent
live is not available
L1 L2
C
LT L
N
NL
LOOP
Power Supply
Wall Switch
C
e
i
l
i
n
g
R
o
s
e
Fan
Earth connection has
been removed for
illustration purposes only
LT LN
Fan
L1 L2
C
NL
LOOP
Power Supply
Wall Switch
C
e
i
l
i
n
g
R
o
s
e
Earth connection has
been removed for
illustration purposes only

©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try and make sure they are as accurate as possible. In the interest of continuous
product development, HiB reserves the right to alter specifications as necessary. E & OE.
T: [phone] F: [phone] E: [e-mail] hib.co.uk
Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN
WEEE compliance
Must not be mixed with
general household
waste
Timer System
Wiring diagram for lamp
The timer circuit is under mains Voltage. Ensure mains power supply is switched off before making
any adjustments.
The fan is operated by turning on the wall
switch. When the switch is turned off the fan
will continue to operate within the set perios
of time. Adjustable between 2-30mins. This
can be adjusted by turning the potentionme-
ter T clockwise to increase and anticlockwise
to decrease the run time.
Cool White and Warm White illuminated fans.
ONLY
use the
screwdriver
provided
to adjust
the timer
setting.
AC in DC out
Live is RedLive supply is Red or Brown
Neutral supply is Blue or Black Neutral is Black
Maintenance
In order to maintain the safe and effective operation of the fan regular maintenance must be performed
Fan maintenance is to be performed only aer the fan is disconnected from the mains power supply.
This includes periodic cleaning of the surface of dust and dirt.
All surfaces should be cleaned with a diluted detergent and a so cloth. Avoid water dripping on the electric
components. Wipe the surfaces dry aer cleaning.
Aercare service - In the unlikely event that this product should fail, please contact HiB customer services.
The details are shown below.
This product contains a light source of energy efficiency class E
Electrical Information