HIK VISION DS-KD-M User manual

Hikvision Video Intercom
Quick Start Guide (QSG): Configuring a DS-KD-DIS Display Module
Hik ision USA Inc., 18639 Railroad St., City of Industry, C 91748, US • Hikvision Canada, 4848 rue Levy, Saint Laurent, Quebec, Canada, H4R 2P1
Telephone: [phone] • Toll Free in US : [phone] • E-Mail: [e-mail] • www.hikvision.com
© 2019 Hikvision US Inc. • ll Rights Reserved • ny and all information, including, among others, wordings, pictures, and graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd., or its
subsidiaries (hereinafter referred to as “Hikvision”).
This user manual (hereinafter referred to as “Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Unless
otherwise stipulated, Hikvision does not make any warranties, guarantees, or representations, express or implied, regarding the Manual.
About this Manual: The Manual includes instructions for using and managing the product. Pictures, charts, images, and all other information hereinafter are for description and explanation only. The information
contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version on the company Website (http://www.hikvision.com/us). Use this Manual
under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners.
Legal Disclaimer: TO THE M XIMUM EXTENT PERMITTED BY PPLIC BLE L W, THE PRODUCT DESCRIBED, WITH ITS H RDW RE, SOFTW RE, ND FIRMW RE, IS PROVIDED “ S IS,” WITH LL F ULTS ND ERRORS, ND HIKVISION
M KES NO W RR NTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMIT TION, MERCH NT BILITY, S TISF CTORY QU LITY, FITNESS FOR P RTICUL R PURPOSE, ND NON-INFRINGEMENT OF THIRD P RTY. IN NO EVENT WILL
HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR GENTS BE LI BLE TO YOU FOR NY SPECI L, CONSEQUENTI L, INCIDENT L, OR INDIRECT D M GES, INCLUDING, MONG OTHERS, D M GES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION, OR LOSS OF D T OR DOCUMENT TION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION H S BEEN DVISED OF THE POSSIBILITY OF SUCH D M GES.
REG RDING TO THE PRODUCT WITH INTERNET CCESS, THE USE OF PRODUCT SH LL BE WHOLLY T YOUR OWN RISKS. HIKVISION SH LL NOT T KE NY RESPONSIBILITIES FOR BNORM L OPER TION, PRIV CY LE K GE, OR OTHER
D M GES RESULTING FROM CYBER TT CK, H CKER TT CK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNIC L SUPPORT IF REQUIRED.
SURVEILL NCE L WS V RY BY JURISDICTION. CHECK LL RELEV NT L WS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE TH T YOUR USE CONFORMS TO THE PPLIC BLE L W. HIKVISION SH LL NOT BE
LI BLE IN THE EVENT TH T THIS PRODUCT IS USED FOR ILLEGITIM TE PURPOSES.
IN THE EVENT OF NY CONFLICTS BETWEEN THIS M NU L ND THE PPLIC BLE L W, THE L TER PREV ILS.
Regulatory Information
FCC Information
FCC Compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
FCC Conditions: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
EU Conformity Statement
This product and, if applicable, the supplied accessories too are marked with “CE” and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2004/108/EC,
the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE Directi e): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info
2006/66/EC (Battery Directi e): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery
information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a
designated collection point. For more information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance: This device meets the C N ICES-3 ( )/NMB-3( ) standards requirements.
Safety Instruction: These instructions are intended to ensure that the user uses the product correctly to avoid danger or property loss. The precautions are divided into “Warnings” and “Cautions.”
WARNINGS: Follow these safeguards to prevent serious injury or death; serious injury or death may occur if any of the warnings are
neglected.
•Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user.
•In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Refer to technical specifications for detailed information.
•Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 24 V C or 12 VDC according to the IEC60950-1 standard. Refer to technical specifications for detailed
information.
•Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard.
•Make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed.
•If smoke, odor, or noise rise from the device, turn off the power at once and unplug the power cable, and then contact the service center.
CAUTIONS: Follow these precautions to prevent potential injury or material damage; injury or equipment damage may occur if any of the
cautions are neglected.
•Make sure the power supply voltage is correct before using the device.
•Do not drop the device or subject it to physical shock.
•If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently. If the device will not be used for an extended period, protect it from dirt.
•Do not place the device in extremely hot, cold, dusty, or damp locations, and do not expose it to high electromagnetic radiation. Do not operate product in outside of its stated environmental specs.
•To avoid heat accumulation, good ventilation is required for the operating environment.
•Keep the device away from liquids while in use.
•While in delivery, the device shall be packed in its original packing, or packing of the same durability.
•Regular part replacement: some equipment parts (e.g., electrolytic capacitor) shall be replaced regularly according to their average endurance time. The average time varies because of differences between
operating environments and usage history, so regular checking is recommended for all users. Contact your dealer for more details.
•Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery
manufacturer.
•If the product does not work properly, contact your dealer or the nearest service center. Never attempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by
unauthorized repair or maintenance.)

QSG Configuring a DS-KD-DIS Display Module
QSG How To Configure a DS-KD-DIS Display Module 112719N 2
Configuring a Hik ision Video Intercom DS-KD-DIS Display Module


Preparation−
−−
−The following items are required for configuration:
•Display Module (DS-KD-DIS, v1.0.0_190520)
•Main Unit (DS-KD-8003-IME1, v2.0.6_190808 above)
•Sub Module (DS-KD-KP/DS-KD-M/ DS-KD-KK, v1.0.0_190522)
•Client Software iVMS-4200 (v3.1.11 and above)
NOTES: If the keyboard module is not connected, the display module directly enters the
address book interface; if the keyboard module is connected, the display module will
show the main interface. Press the Up (∧
∧∧
∧) and Down (∨
∨∨
∨) arrow keys to enter the
address book interface.
The maximum number of modules is eight, or a maximum of five if the display module
is included. The maximum number of sub-modules is as follows:
-Maximum Nametag Modules: 8
-Maximum Keyboard Modules: 1
-Maximum Card Modules: 5
-Maximum Display Modules: 1
It is recommended to upgrade the other sub-modules’ firmware before upgrading the
display module firmware.
Make sure all related devices are powered off during wiring.


Wiring
1. Configure the sub module DIP switches. Each sub-module’s DIP switch address should be unique
for connecting to the main unit. The sub module DIP switches and corresponding DIP switch status
are displayed below (DIP switches 1, 2, 3, and 4 are used to code the sub module address; valid sub
module addresses are from 1 to 8).

QSG Configuring a DS-KD-DIS Display Module
QSG How To Configure a DS-KD-DIS Display Module 112719N 3


Calling a Resident ia the Address Book
1. Configure the door station and indoor station Room No. (default room number is “1”)
2. ssociate the room number with a specific person.
a. Click the Person icon on the iVMS-4200 to display the interface.
b. Create the organization, add the person, and fill in the name and resident information.
c. Click the Access Control icon on the iVMS-4200 to display the interface.
d. Click the Access Group icon.
e. dd the permission group, choose All-Day Authorized template, and select the person and
door.
f. Click Apply All to the device, and the display module will show the “importing” status.

QSG Configuring a DS-KD-DIS Display Module
QSG How To Configure a DS-KD-DIS Display Module 112719N 4
3. Press the Up (∧
∧∧
∧) or Down (∨
∨∨
∨) keys on the display module to enter the address book interface. The
address book will automatically show the person and corresponding room number.
4. Select the name displayed in the address book, press OK to enter the confirmation interface, and
then press OK again to call the indoor station that corresponds to the room number (long press the
Up (∧
∧∧
∧) and Down (∨
∨∨
∨) keys to speed up the page flipping speed of the address book).

QSG Configuring a DS-KD-DIS Display Module
QSG How To Configure a DS-KD-DIS Display Module 112719N 5


Calling a Resident ia the Keypad Module
1. You can call a resident via the keypad module. When a number is input via the keyboard module,
the display module simultaneously displays the number. When finished entering the room number,
press the # key to start the call.


Unlocking a Door ia the Keypad Module
1. Follow the operation process displayed on the display module to unlock the door, the password
formats are as follows:
•【#】+ Public Password +【#】
•【#】+ Unlock Password +【#】
•【#】+ Duress Password +【#】
2. When entering the unlock password, the public password, or the duress password, the display
module will update in real time and prompt that the door is open, the password is wrong, etc.