Hillrom Welch Allyn Spot Vital Signs 4400 User manual

Welch Allyn®
Spot Vital Signs 4400
Quick reference
Power button
• Located on the device housing
• Powers up the device
• When the device is on, opens pop-up dialog with controls
to power down, enter sleep mode, or cancel out of the
power menu
Power down
1. Touch the power button.
2. Touch Power down.
Battery status
Charging Battery removed or
not holding a charge
Approximate
operating time
remaining
NIBP measurement
Stat/Stop Stat average/Cancel/Skip
START STOP
CANCEL
START
AVERAGE
SKIP
START STOP
CANCEL
START
AVERAGE
SKIP
Stat an NIBP averaging program
The averaging program takes consecutive NIBP measurements within a
congurable amount of time. When the program is complete, the average
measurement is displayed in the Home tab.
1. Place the proper cu around the patient’s bare upper arm.
2. On the Home tab, touch Start Average.
3. If necessary, touch Skip to stop the current measurement. The
measurement restarts at the end of the countdown.
4. When averaging completes, touch Save to save the patient data, or touch
Clear to discard the data.
Results of an NIBP averaging program
NIBP AVERAGED
SYS/DIA mmHg ( 76 MAP )
111/62 1. 120/80
2. 123/82
3. 110/64
4. 111/62
5. 108/61
6. 105/59
TOTAL READINGS AVERAGED: 4
Displays the average of the readings.
Displays “NIBP AVERAGED.”
Displays the readings taken by the program. A reading with a line
through it is excluded from the average.
Note To retain an NIBP average, touch Save.

Manually enter vitals measurements
NIBP
SYS/DIA mmHg ( MAP ) /MIN
PULSE RATE
SpO2 TEMPERATURE
°F (°C)
START
AVERAGE
START
1. Press and hold a frame, such as NIBP. A pop-up dialog appears.
2. On the left, touch an empty eld and enter the vitals measurement.
3. Touch OK.
4. When you are nished entering measurements, touch OK.
5. Touch Save to save the patient data.
Enter additional parameters
SaveClear
Home Review Settings
Height
in lbs
Weight Pain
bpm
RR BMI
Adult
1. Touch the Additional parameters frame.
2. Modify the parameters as desired. If height and weight are entered, BMI will
be automatically calculated.
3. Touch OK.
4. When you are nished entering measurements, touch OK.
5. Touch Save to save the patient data.
Clean the equipment
CAUTION Do not use unapproved cleaning agents. Use of
unapproved cleaning agents may cause damage to
components.
See “Prepare to clean the equipment” in Directions for use
for a list of approved cleaning agents.
Follow the cleaning agent manufacturer’s instructions to prepare solution,
if applicable, and clean all exposed surfaces of the device, basket, cords and
cables, and stand. Wipe all surfaces until no visible soil remains. Change the
wipe or cloth throughout the cleaning procedure as needed.
1. Disconnect the AC power cord from the mains outlet.
2. Wipe the top of the device.
3. Wipe the sides, front, and rear of the device.
4. Clean the LCD screen with an agent that is approved for cleaning the
display. To avoid residual lm buildup after cleaning, wipe the LCD screen
with a clean cloth dampened with water and then wipe the screen dry with
a dry cloth.
5. Wipe the bottom of device.
6. Wipe the AC power cord.
7. Wipe the stand from top to bottom.
Pull vitals data into an EMR
Refer to hillrom.com to learn how to integrate the Spot 4400 with your
EMR provider. Once the device is integrated, you can pull patient vitals
measurements to your EMR host computer using the USB cable provided.
Hillrom Technical Support
hillrom.com/en-us/about-us/locations/
Welch Allyn, Inc. is a subsidiary of Hill-Rom Holdings, Inc.
hillrom.com 80025232 Ver. B Revision date: 2019-09 © 2019 Welch Allyn, Inc. All rights reserved.