Hinkley SCULPT 80 User manual

CEILING FAN INSTRUCTION MANUAL
INDOOR / OUTDOOR LED FAN
80" SCULPT™
DC
DC MOTOR LED
PAIR WITH HINKLEY APP
HINKLEY
DOWNLOAD ON APP STORE or GOOGLE PLAY
CONTROL
READY
TO USE.
CONTROL
PRE-PAIRED.

SO WE’REHEREIF YOU HAVE A QUESTION, NEED SOME
HELP OR WANT TO CHAT ABOUTOUR PRODUCTS. SEND
SUGGESTIONS OUR WAY TOO—WE’REALWAYS LOOKING TO
MAKE YOUR EXPERIENCE WITH HINKLEY A POSITIVE ONE.
This manual contains complete instructions for the
installation and operation ofthis fan. It has been
designed to make the installation process as easy as
possible. If you are unfamiliar or uncomfortable with
wiring, please contact a qualified electrician. If you
need additional assistance or have any questions,
please reach out to us.
For warranty information,visit hinkley.com.
> [e-mail]
> 800.HINKLEY
> LET’S SEE THAT HINKLEY STYLE @Hinkleylighting
#HINKLEYSTYLE
WE WANT YOU TO LOVE YOUR NEW FAN

WARNING:
Read and follow these instructions carefully and be mindful of all warnings shown throughout.
©2023 Hinkley Lighting, Inc. |hinkley.com |01
TABLE OF CONTENTS
READY
TO USE.
CONTROL
PRE-PAIRED.
NOTE: If PAIRING is necessary, refer to the control pairing instruction
in the operation section of this Instruction Manual.
02 GENERAL INSTALLATION & OPERATING
INSTRUCTIONS
03 IMPORTANT SAFETY PRECAUTIONS
03 TOOLS & MATERIALS REQUIRED
04 UNPACKING YOUR FAN
05 PREPARATION
05 INSTALLING THE HANGING BRACKET
06 HANGING THE FAN
08 ELECTRICAL CONNECTIONS
09 CEILING CANOPY INSTALLATION
10 INSTALLATION OF THE BLADES
11 INSTALLING THE LED KIT AND GLASS SHADE
13 INSTALLING THE WALL CONTROL
15 OPERATION
17 CARE AND CLEANING
17 TROUBLESHOOTING
18 ENERGY GUIDE
18
19
SPECIFICATIONS
HINKLEY APP / WIFI

02 |hinkley.com
GENERAL INSTALLATION & OPERATION INSTRUCTIONS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning.
To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring. All electrical connections
must be made in accordance with local codes, ordinances and/or the National Electric Code. If you are unfamiliar with the
methods of installing electrical wiring and products, secure the services of a qualified and licensed electrician as well as
someone who can check the strength of the supportive ceiling members and make the proper installation(s) and connections.
WARNING: To reduce the risk of fire, electric shock, or other personal injury, mount fan only on an outlet box or supporting system
marked acceptable for fan support of 35 lbs (15.9 kg) or less and use mounting screws provided with the outlet box. Most outlet
boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced.
Consult a qualified electrician if in doubt.
Make sure that your installation site will not allow rotating fan blades to come in contact with any object. Blades should be at least
7 feet from floor.
Blades should be attached after motor housing is hung and in place. Fan motor housing should be kept in the carton until ready
to be installed to protect its finish. If you are installing more than one ceiling fan, make sure that you do not mix fan blade sets, as
each blade is part of a weighted set.
After making electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The
wires should be spread apart with the common conductor and the grounding conductor on one side of the outlet box, and the
"HOT" wires on the other side.
Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL listed and should be installed
per the light kit's installation instructions.
After fan is completely installed, check to make sure that all connections are secure to prevent fan from falling and/or causing
damage or injury.
The fan can be made to work immediately after installation - the bearings are adequately charged with grease so that, under
normal conditions, further lubrication should not be necessary for the life of the fan.
To operate the reverse function on this fan, press the reverse button while the fan is running.
CAUTION: Do not ingest battery - Chemical bum hazard. Keep new and used batteries away from children.
The remote control supplied with a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe
internal bums in just 2 hours and can lead to death.
If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

©2023 Hinkley Lighting, Inc. |hinkley.com |03
IMPORTANT SAFETY PRECAUTIONS
TOOLS &MATERIALSREQUIRED
WARNINGS:
•PHILLIPS SCREWDRIVER
• FLAT SCREWDRIVER
•WRENCH OR PLIERS
•WIRE CUTTER
• STEPLADDER
•WIRINGSUPPLIES AS REQUIRED BY
ELECTRICAL CODE
• Disconnect power by removing fuse or turning off circuit breaker before installing the fan and/or optional lighting.
• Support directly from building structure.
• To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked "acceptable for fan support" and use mounting
screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan
support and may need to be replaced. Consult a qualified electrician if in doubt.
• Do not use an incandescent light dimmer. Do not use this fan with any transformer type fan speed control device.
• To reduce the risk of personal injury, do not bend the blade arms when installing them, balancing the blades or cleaning the fan.
Do not insert any object(s) between rotating fan blades.
NOTE:
The important precautions, safeguards and instructions appearing in this manual are not meant to cover all possible conditions
and situations that may occur. It must be understood that common sense, caution and carefulness are factors which cannot be
built into this product. These factors must be supplied by the person(s) installing, caring for and operating the unit.

04 |hinkley.com
UNPACKING YOUR FAN
UNPACK YOUR FAN AND CHECK THE CONTENTS.
• Do not discard the carton. If warranty replacement or repair is ever necessary, the fan should be returned in original packing.
Remove all parts and hardware. Do not lay motor housing on its side, or the decorative housing may shift, be bent or damaged.
• Examine all parts. You should have the following:
3
9
10
11
12
13
4
5
6
7
8
+
NOTE: Design of parts shown above may look slightly different for
your specific model of fan.
SCULPT PACKAGE CONTENT
1 Blade Set of 3
3
2Blade Support Plates
4
Hanging Bracket
6
14
Ceiling Canopy and Trim Ring
Downrod Asm.
Yoke Cover
Adapter Plate
Hardware Bag
Bracket Mounting Hardware (wood
screws, screws, lock washers, star
washers, flat washers, wire nuts),
Blade to Motor Screws w/Lock
Washers, Safety cable hardware
(wood screw, flat washer), Allen
wrench, Balance Kit, Lead Wire
Extension (preassembled).
XX=FAN FINISH
x
In Hardware Bag
5
7
8
9
12
11
10
13
16W LED Kit
Metal Cover (for no light use)
Glass Shade
Controller Incl. 9 Wire Nuts
Cradle A, Wall Plate, Face Plate,
2 Mounting Screws, Cradle B
(for flat wall use only)
Wall Control w/2032 Battery,
Fan Housing with Motor
*Remove rubber shipping supports
around motor, if applicable. Save
the screws.
14
1
2
AP903856Fxx
CWT903680
LKC903856Fxx
GL903856OPET
LK903856Fxx
980014FWH-R
MH903680
YC900460Fxx
DR94016Fxx
CA902672Fxx
BL903680

©2023 Hinkley Lighting, Inc. |hinkley.com |05
PREPARATION
INSTALLING THE HANGING BRACKET
PREPARATION:
Parts identification on assembled fan.
Verify you have all parts before beginning the
installation. Check pulp insert closely for missing
parts. Remove motor from packing. To avoid
damage to finish, assemble motor on soft padded
surface or use the original pulp inset in motor box.
DO NOT LAY MOTOR HOUSING ON ITS SIDE AS
THIS COULD RESULT IN SHIFTING OF MOTOR
IN DECORATIVE ENCLOSURE.
1
2
3
Fig. 1
CAUTION: To avoid possible electrical shock, be sure electricity is
turned off at the main power box before wiring. All wiring must be
in accordance with National and Local Electrical Codes and the
ceiling fan must be grounded as a precaution against possible
electric shock.
Locate ceiling joist where fan is to be mounted, being sure
location agrees with the requirements in the minimum
clearance section of this guide. Wood joists must be
sound and of adequate size to support 35 pounds (See
page 2, items 3 and 4).
If not already present, mount a UL listed outlet box marked
"suitable for fan support" following the instructions
provided with the outlet box. The outlet box must be able
to support a minimum of 35 pounds.
Attach hanging bracket to outlet box using screws
provided with the outlet box.
Hanger bracket
Flat washer
Spring washer
Outlet box screw
Ceiling fan
outlet box
Light kit
Downrod
Blade
Yoke cover
Canopy
Motor housing

06 |hinkley.com
HANGING THE FAN
Downrod
Hanger
ball
Set screw
Cross pin
1
2
3
4
5
Remove ball from downrod by loosening set screw in the
side of the ball. Slide ball down and remove cross pin;
remove ball. (Fig. 1)
Carefully support fan body (motor) in its pulp packing with
the mounting collar (where the wires come out) facing
upward.
Loosen the two security set screws and remove the downrod
pin and cotter clip from the coupling on top of the motor
assembly. (Fig. 2)
Carefully feed the electrical lead wires and safety cable
from the fan through the downrod. Thread downrod into
coupler until holes align. Insert downrod pin through holes
in mounting collar and downrod; clip cotter pin through
small hole in end of downrod pin to hold downrod in place.
Tighten security set screws against downrod using a large
flat blade screwdriver to ensure a tight fit against downrod.
Fig. 1
Fig. 2
Mounting collar
Downrod pin Cotter pin
Downrod
Safety cable
Security screws
Lead wires

©2023 Hinkley Lighting, Inc. |hinkley.com |07
Fig. 4
Attach the wood screw and the flat washer to the ceiling joist as
shown (do not fully tighten). Slide the cable clamp onto the safety
cable from the fan. Loop the safety cable around the wood screw
that was just attached to ceiling joist. Feed the end of the cable
into the clamp and pull as much cable through as possible. Firmly
tighten screw in the clamp. Cut off excess cable and tighten the
wood screw to ceiling joist.
INSTALLATION OF SAFETY CABLE SUPPORT
6
7
8
NOTE:
6 feet of lead wire is supplied on the fan for use with
longer downrods.
Slip the yoke cover, trim ring and canopy onto the downrod.
(Fig. 3)
Slide the hanger ball onto the downrod, insert the cross pin
through the downrod and tighten. Tighten the set screw.
Lift ball/downrod/fan into hanger bracket opening.
NOTE: The tab opposite hanger bracket opening should fit
in slot on ball. (Fig. 4)
REMEMBER to turn off the power before you begin.
To properly install your ceiling fan, follow the steps below.
Safety cable clamp
Safety cable
Wood ceiling joist
Safety cable loop
Wood screw and washer
Top of
fan body
Yoke cover
Canopy
Trim ring
Fig. 3
Hook-up (5) wires
Downrod
Hanger ball
Set screw
Cross pin
*
*IMPORTANT: Take the lead wires and make sure that you
have pulled them all the way through the top of the dawnrod.
Star at the TOP of the downrod and measue 8 in. of lead wire,
and then cut the excess wires off with wire cutters (not included).

08 |hinkley.com
ELECTRICAL CONNECTIONS
Fig. 1
Hanger
bracket
Receiver
Fig. 2
CONTROLLER
FAN
OUTLET BOX
CEILING
WH (AC IN)
WH
BLK
BLK (AC IN) GROUND
RED
YELLOW
GRAY
GRAY
RED
YELLOW
BLUE
WHITE
BLUE
WHITE
YELLOW / GRN (hanger bracket)
YELLOW / GRN (downrod)
YELLOW / GRN
REMEMBER -Turn off the power! NOTE - Control must be installed
within 30 feet of fan.
WARNINGS: Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire nuts, except for
the ground wire.
CAUTION: To reduce the risk of electric shock, this fan must be
installed with an isolating wall control/switch. Turning off the isolating
wall switch can override any smart enabled or remote operation
commands.
1. Insert the controller into the ceiling mounting bracket with the
flat side of the controller facing the ceiling. (Fig. 1) For best
performance, make sure the Black Antenna and WIFI Antenna,
on the end of the controller, remains extended and not tangled
with any of the electrical wires.
2. Make wire connections from the fan to the controller unit. For
this step use the bundle of 5 wires on the controller. (Fig. 2)
Connect the YELLOW lead wire extension wire to the YELLOW
controller wire.
Connect the GRAY lead wire extension wire to the GRAY
controller wire.
Connect the RED lead wire extension neutral wire to the RED
controller neutral wire.
Connect the WHITE lead wire extension neutral wire to the
WHITE controller neutral wire.
Connect the BLUE lead wire extension neutral wire to the BLUE
controller neutral wire.
3. Connect the wiring from the ceiling to the controller unit. (Use the
2 wire bundle on the controller.) Secure with supplied wire nuts.
Connect the BLACK building supply wire to the BLACK
controller wire.
Connect the WHITE building neutral wire to the WHITE
controller neutral wire.
Connect the COPPER building ground wire to the 3 YELLOW/
GREEN ground wires from the fan and controller.
Turn the wire nut connections upward, spreading them apart so
the green (ground) and white wires will be on one side of the
outlet box and the black wire will be on the other side.

©2023 Hinkley Lighting, Inc. |hinkley.com |09
CEILING CANOPY INSTALLATION
1
2
3
Tuck connections neatly into ceiling outlet box.
Remove one screw on bracket and slide the canopy up to
mounting bracket and place the key hole on screw on the
mounting bracket, turn canopy until it locks in place at the
narrow section of the key holes.
Align the circular hole on canopy with the remaining hole
on the mounting bracket, secure by tightening the two set
screws.
NOTE: Adjust the canopy screws as necessary until the
canopy and trim ring are snug.
WARNING:
Make sure the hook on the hanging bracket properly sits in the groove in the hanger ball before
attaching the canopy to the bracket by turning the housing until it drops into place.
NOTE:
Follow this step ONLY if you did not cut the extra length from
the wires coming from the ceiling fan.
Canopy
Screws
Trim ring
Ceiling fan
outlet box
Hanger bracket Groove
Fig. 1

WARNING: To reduce the risk of personal injury, do not bend the
blades while installing, balancing the blades, or cleaning the fan.
Fasten the blade to the motor, through the blade support
plates, with the provided screws and lockwashers. Make
sure screws are TIGHT! Loose motor screws can contribute
to unnecessary noise during operation.
Repeat this process to attach the other blades.
10 |hinkley.com
1
2
Fig. 1
NOTE:
Cordless power screwdrivers are NOT recommended,
as they usually strip the heads of the screws and
usually will not fully compress the lock washers on
the motor screws.
INSTALLATION OF THE BLADES
Screws
Blade support plates
Blades

©2023 Hinkley Lighting, Inc. |hinkley.com |11
INSTALLING THELIGHT KIT AND GLASS SHADE
1
2
3
4
5
6
7
5
NOTE: Before starting installation, disconnect the power by
turning off the circuit breaker or removing the fuse at fuse
box. Turning power off using the fan switch is not sufficient
to prevent electric shock.
If you do not wish to install the light kit, skip this
step and proceed to next step.
Remove one of the three screws on the mounting hub
located on the fan motor. Loosen the other 2 screws. (Do
not remove) (Fig. 1)
Place the key holes on the adapter plate over the 2 screws
previously loosened, turn the adapter plate until it locks in
place at the narrow section of the key holes. Secure by
tightening the 2 screws previously loosened and the one
previously removed.
Remove one of the three screws on the adapter plate
located on the fan motor. Loosen the other 2 screws. (Do
not remove) (Fig. 2)
Fig. 1 Fig. 2
While holding the LED light kit under your fan, make the
polarized plug connections: (Fig. 2)
- White to white
- Black to blue
Tuck connections neatly into adapter plate. Place the key
holes on the light kit over the 2 screws previously loosened,
turn the light kit until it locks in place at the narrow section of
the key holes. Secure by tightening the 2 screws previously
loosened and the one previously removed.
Raise the glass shade or metal cover against the LED light kit
and turn clockwise until snug, DO NOT OVERTIGHTEN.
Restore power and your light kit is ready for operation.
Adapter
plate
Wire connectors
Light kit
Glass shade
Screws
Mounting hub
(bottom of motor)
Adapter plate
Screws

12 |hinkley.com
FAN WITHOUT LIGHT KIT (OPTIONAL)
Fig. 1
Fig. 2
WARNING: Before starting installation, disconnect the power by
turning off the circuit breaker or removing the fuse at fuse box.
Turning power off using the fan switch is not sufficient to prevent
electric shock.
NOTE: The metal plate assemblyr included with your fan is an
option to replace the LED light kit for the light in the event that
you prefer not to use the light feature of your fan. The metal plate
assembly is not necessary for the light operation; it can be saved
for later use if desired.
2
3
4
5
6
7
Remove six Allen screws located in the metal plate assembly
by using the allen wrench provided. Take out the metal
cover from adapter plate. (Fig. 1)
Remove one of the three screws on the mounting hub
located on the fan motor. (Fig. 2)
Loosen the other two screws.
Install adapter plate to mounting hub.
Line up the two slotted holes with the two loose screws on
the mounting hub located on fan motor.
Re-install the third screw previously removed and tighten
all three screws.
Install metal cover to the adapter plate with six allen screws
previously removed by using the allen wrench provided.
(Fig. 2)
1
Adapter plate
Metal cover
Adapter plate
Metal cover
Allen wrench
Allen wrench
Allen
screws
Allen
screws
Screws
Mounting hub
(bottom of motor)

©2023 Hinkley Lighting, Inc. |hinkley.com |13
INSTALLING THE WALL CONTROL
Fig. 1
REMEMBER to turn off the power before you begin.
NOTE - Secures to any surface or application: flat wall, single gang
box, multi gang box.
1
2
3
4
Option 1. Flat Surface Installation
Select a desired location. Use the wall plate to mark the
location of the mounting holes. Plastic wall anchors or
mounting screws are needed for this application. (Fig. 1)
Seat the cradle B into the wall plate. Secure the wall plate
to the wall using the provided hardware.
Snap the face plate cover onto the wall bracket.
Remote transmitter will be held in place with built in magnets.
Remove the existing wall plate and the old switch from the
wall outlet box.
Seat the cradle A into the wall plate. (Fig. 2)
Connect the black lead wires from the switch in the cradle A
to the black wires in the switch box. Hot input wire to one of
the cradle A switch leads. Power lead to the fan is connected
to the remaining switch lead.
Connect the wall plate/cradle A assembly to the wall outlet
box using the supplied hardware.
Snap the face plate cover onto the wall bracket.
Remote transmitter will be held in place with built in magnets.
1
2
3
4
5
6
Option 2. For single gang box
Transmitter
Face plate
Wall plate Cradle B
Wall
Plastic
anchor
Fig. 2
Outlet box
Transmitter
Face plate
Wall plate
Cradle A
HIRO Control System

14 |hinkley.com
Fig. 3
Remove the existing wall plate and old switch from the wall outlet box. (Fig. 3)
Connect the black lead wires from the switch in the cradle A to the black wires in the switch box. Hot input wire to one of the cradle
switch leads. Power lead to the fan is connected to the remaining switch lead. (Fig. 4)
Attach the cradle A to the wall switch box using the supplied hardware.
Attach the multi-gang faceplate (not provided) to the switch set in the wall outlet box. Cradle A of Hinkley switch will fit in any
standard decora face plate.
Remote transmitter will be held in place with built in magnets.
1
2
3
4
5
Option 3. Multi Gang Wall Switch Box Installation
Outlet box
Face plate
Switch
Fig. 4
Outlet box
Transmitter
Face plate
Cradle A
HIRO Control System

©2023 Hinkley Lighting, Inc. |hinkley.com |15
OPERATION
Your DC brushless motor is equipped with
an automatically learned type remote control.
There is no frequency switches on the
receiver or transmitter. The fan can start to
use once the pairing process is done.
Remove the panel from the transmitter and
then install one 2032 battery (included). You
need to use a coin to open or close the battery
cover. To prevent damage to transmitter,
remove the battery if not use for long periods
of time (Fig. 1)
Fig. 1
Fig. 2
Signal light
ON
OFF
WARNING: Chemical Burn Hazard.
Keep batteries away from children.
This product contains a lithium button/coin
cell battery. If a new or used lithium button
/coin cell battery is swallowed or enters the
body, it can cause severe internal burns
and can lead to death in as little as 2 hours.
Always completely secure the battery
compartment. If the battery compartment
does not close securely, stop using the
product, remove the batteries, and keep it
away from children. IF you think batteries
might have been swallowed or placed inside
any part of the body, seek immediate medical
attention.
The batteries shall be disposed of properly,
including keeping them away from children;
Even used cells may cause injury.
HIRO Control System
Pairing Process
NOTE: If installing/pairing more than
one fan in an area, the power must be
disconnected from all fans except the
one fan being paired.
NOTE: Fan must be fully installed
with the blades prior to pairing the
controls.
With the fan’s power off, restore power to
the fan. Press and hold “ ” button for about
5 seconds and release. If optional light kit is
installed, the light kit will flash three times
and the motor spin up for 10 seconds on low
speed. The fan has completed the pairing
process with the wall control and is ready
for use.
NOTE: A single fan can be controlled with as
many as 3 wall controls in one room. Every
control will need to repeat the pairing
process based on instructions above and
all controls must be within 30 feet of the fan.
1
2
3
4
5
button:
Press and release this button to turn
the light on / off.
button:
Press these buttons to dim or brighten
the lights to the desired level and
release.
button:
Press this button to set fan wind
direction up or down.
button:
Press these buttons to adjust fan
speeds up / down between speeds 1
and 6
button:
Press and release this button to turn
the fan on / off.
Signal light (Fig. 2)
6

16 |hinkley.com
Fig. 3 Fig. 4
SUMMER MODE
(COUNTERCLOCKWISE DIRECTION)
WINTER MODE
(CLOCKWISE DIRECTION)
1
2
3
Summer Mode (forward):
A DOWNWARD airflow creates a cooling effect as shown in Figure 3. This allows you to set your air conditioner on a warmer setting
without affecting your comfort.
Winter Mode (Reverse):
An UPWARD airflow moves warmer air off the ceiling area as shown in Figure 4. This allows you to set your heating unit on a cooler
setting without affecting your comfort.
Airflow direction can be changed between summer mode and winter mode by pressing the reverse button on the HIRO control.
Summer Mode and Winter Mode Operation

©2023 Hinkley Lighting, Inc. |hinkley.com |17
CARE AND CLEANING
TROUBLESHOOTING
CAUTION:
Switch off power supply before carrying out any of these checks.
PROBLEM SOLUTION
Periodically it may be necessary to re-tighten blade to blade arm screws or blade arm to motor screws to prevent clicking or humming
sound during operation. This is especially true in climates with broad temperature and humidity ranges.
When dusting the blades, you must support the blade to prevent bending - no pressure should be applied to the blades. If you experience
any flaws in the operation of your fan, please check the following points.
FAN WILL
NOT START
FAN SOUNDS
NOISY
FAN WOBBLES
1. Check to assure that a new batteries is installed in the remote or wall control. Check circuit fuses or breakers.
2. Check wall control LED indicator light. If LED is not illuminated when pushing a button, it is not transmitting a
signal. Please check battery, power to wall control/circuit breaker and all electrical connections.
3. Assure that there are no more than 12 fans operating on a circuit through an on/off wall switch or a breaker (not
through a wall control).
4. Assure that the fan in within range of the WiFi (150 ft.) or wall control (30 ft.).
1. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan will disappear during this time.
2. Make sure all motor housing screws are securely fastened.
3. Make sure the screws that attach the fan blade to the fan are tight.
4. Make sure your ceiling box is secure and rubber isolator pads are used between the mounting bracket and outlet
box.
1. Check that all blade to motor and blade arm screws are secure.
2. If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight
and possibly result in smoother operation.
3. Make sure the mounting plate is securely fastened to the ceiling outlet box.
4. Make sure ceiling box is secure.

18 |hinkley.com
ENERGY GUIDE SPECIFICATIONS
ftc.gov/energy
• The higher the airflow, the
more air the fan will move
• Airflow Efficiency: 299 Cubic
Feet Per Minute Per Watt
Airflow
6,873
Cubic Feet Per Minute
• Based on 12 cents perkWh and 6.4 hours use perday
• Your cost depends on rates
• Energy Use: 23 Watts
and use
$
3
$
34
Cost Range of Similar Models (19” – 84”)
$6
Estimated
Yearly Energy Cost
All estimates based on typical use, excluding lights
Airflow Shown Is a Weighted Average of High and Low Cubic Feet per Minute Based on Close to Ceiling
AVERAGE PERFORMANCE AND ENERGY INFORMATION
3786
9597
33.6 4.0
286 946
PERFORMANCE
SPECIFICATIONS
STANDARD
HIGH SPEED LOW SPEED
Airflow (CFM)
Energy Use (Watts)
Airflow Efficiency (CFM/W)
Energy Costs (Yearly)
Amps
0.46 0.06
RPMs
115 50
6
$
1
$