Vents-us TwinFresh Expert (Duo) RW1 User manual

www.vents-us.com
TwinFresh Expert (Duo) RW1
VENTS-US
400 Murray Road
Cincinnati, OH 45217
Phone: [phone]
E-mail: [email protected]
1
SINGLEROOM REVERSIBLE ENERGY REGENERATION VENTILATOR
TwinFresh Expert (Duo) RW1
INSTALLATION GUIDE
INSTALLATION
Tools required
Pencil Drill Ø6 mm (/’’), 40 mm (1 /’’) Screwdriver Dowel Ø6 mm (/’’), 40 mm (1 /’’) 4 pcs. Screws Ø6 mm (/’’), 40 mm (1 /’’) 4pcs.
MOUNTING
1. Prepare a round core hole in the outer wall.The hole size is shown in the gure below. While preparing a core hole it is recommended to make preparations for layout of the power
cable and other required cables.
Ø170
min 500
min 500
min 500
A-AA
A
Ø170
Inner side of the wall
Outer side of the wall
2. Install the air duct in the wall and x it with mounting foam.The air duct end must protrude for the distance that enables installation of the outer ventilation hood (see the User’s
manual for the outer ventilation hood).
0 – 3
10 – 110
0 -
1/8
’’
3
/ 8 ’’ - 4
5
/ 16 ’’
Inner side of
the wall
Outer side of
the wall
Seal the centred
air duct using the
mounting foam

www.vents-us.com
TwinFresh Expert (Duo) RW1
2
3. Stick the delivered cardboard master plate on the indoor wall using a mounting tape. The large opening in the master plate must be axially aligned with the air duct. For
aligning the master plate with respect to the horizon line it is recommended to use a builder’s level.Then mark the fastening holes for installation of the supplied dowels and drill the
holes to a required depth. Route the power cable from the wall outside through the specially marked opening on the master plate.
4. Unlatch and detach the front part of the indoor unit from its back part.
The thermal actuator rod
must be in lower position
when installing the front
panel of the
TwinFresh Expert unit.
5. Fix the back part of the indoor unit on the wall with the screws supplied with the mounting kit of the ventilator. Remove the two retaining screws from the left transparent
cover to enable access to the terminals.
VENTS-US
400 Murray Road
Cincinnati, OH 45217
Phone: [phone]
E-mail: [email protected]

www.vents-us.com
TwinFresh Expert (Duo) RW1
VENTS-US
400 Murray Road
Cincinnati, OH 45217
Phone: [phone]
E-mail: [email protected]
3
6. Route the power cable as gured below and connect the ventilator to power mains in compliance with the external wiring diagram, refer to page 4. Fix the power cable and
the signal cables with cable clamps. After completion of the electrical connection re-install the transparent cover to its place.
Cable clamp
7. Install the cartridge into the air duct as gured below.The pointer must be directed upwards.Then x the wire with the protruding clamp and connect the socket connector to
the circuit board.
Insert the wires under the
retaining clip and connect the
connector to the circuit board.
The pointer must
be directed upwards.
8. Install the front part of the indoor unit.The thermal actuator rod must be in lower position when installing the front panel, as shown in the figure in Section 4 on page 2.

www.vents-us.com
TwinFresh Expert (Duo) RW1
4
TwinFresh Expert RW1
9. Insert the sound absorbing material into the air duct from the outside.
Roll the layer of the sound absorbing material to match the air duct diameter. The
protecting paper layer must be outside.
Insert the sound absorbing roll into the cartridge against stop.
Make a mark at the end of the air duct, remove the material and cut the roll as marked.
After that insert the ready roll into the air duct.
TwinFresh Expert Duo RW1
9. Install the sectional air flow separators from the outside. Insert a required number of
the air flow separators in the air duct until they reach the cartridge. Mark the last air flow
separator to be flush with the air duct face, remove it from the air duct and cut the exces-
sive part of the last air flow separator.Tighter fixation is provided if the air flow separator
protrudes to some distance.
Install the adjusted air flow separators in the air duct.
10. Install the outer ventilation hood. For this, see the user’s manual for the hood.
VENTS-US
400 Murray Road
Cincinnati, OH 45217
Phone: [phone]
E-mail: [email protected]

www.vents-us.com
TwinFresh Expert (Duo) RW1
VENTS-US
400 Murray Road
Cincinnati, OH 45217
Phone: [phone]
E-mail: [email protected]
5
CONNECTION TO POWER MAINS
POWER OFFTHE POWER SUPPLY PRIOR TO ANY OPERATIONS WITH THE UNIT.
THE UNIT MUST BE CONNECTEDTO POWER SUPPLY BY A QUALIFIED ELECTRICIAN.
THE RATED ELECTRICAL PARAMETERS OF THE UNIT ARE GIVEN ON THE MANUFACTURER’S LABEL.
The ventilator is rated for connection to single-phase АС 100-240V 50/60 Hz power mains.
Connect the unit to power mains through the external automatic switch with a magnetic trip integrated into the xed wiring system. The tripping current of the circuit breaker is
selected based on the electrical characteristics shown on the label of the fan casing.
For electric installations use insulated, durable and heat-resistant electric leads (cables, conductors) with the minimum cross section 0.5upto0.75mm2 (No.20÷18AWG) for the power
cable and 0.25mm2(No.23AWG) for the control cables. The cable cross-section is given for reference only. The actual conductor cross-section selection must be based on its type,
maximum permissible heating, insulation, length and installation method.
Use copper wires for all the electric connections!
Connect the ventilator to power mains in compliance with the wiring diagram.
EXTERNAL CONNECTIONS DIAGRAM
The ventilator design enables connecting external devices with a normally open
contact (NO-contact), such as an external CO2sensor, a humidity sensor, a switch, etc.
When the normally open contact of the external device is closed, the ventilator goes
to a maximum speed.
The ventilators can be connected in series and in parallel with a central control by the
master ventilator.
In case of in series or in parallel connection of several ventilators power is supplied
either from a previous ventilator or from power mains.
L (~)
N (~)
QF*
N
L
N
L
In
Gnd
NO1
NO2
+12V
Power
АС 100-240V
50/60 Hz
Power to the
next ventilator
Input for 0-10 V
analogue sensor
NO contact
of an external control unit

www.vents-us.com
TwinFresh Expert (Duo) RW1
6
VENTS-US
400 Murray Road
Cincinnati, OH 45217
Phone: [phone]
E-mail: [email protected]

www.vents-us.com
TwinFresh Expert (Duo) RW1
VENTS-US
400 Murray Road
Cincinnati, OH 45217
Phone: [phone]
E-mail: [email protected]
7

www.vents-us.com
TwinFresh Expert (Duo) RW1
8Installation Guide133EN-01
VENTS-US
400 Murray Road
Cincinnati, OH 45217
Phone: [phone]
E-mail: [email protected]