Hirschmann RS20 series User manual

RM Web
Release 6.0 07/2010
Technical Support
[email protected]
Reference Manual
Web-based Interface
Industrial ETHERNET (Gigabit) Switch
RS20/RS30/RS40, MS20/MS30, OCTOPUS

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2010Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. For devices with embedded software, the end-user license agreement on the
enclosed CD applies.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann-ac.de).
Printed in Germany
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
Rel. 6.0 1-01-07/2010 – 14.7.10

Contents
About this Manual 7
Key 9
Opening the Web-based Interface 11
1 Basic Settings 15
1.1 System 16
1.2 Network 21
1.3 Software 23
1.3.1 View the software versions present on the device 23
1.3.2 TFTP Software Update 24
1.3.3 HTTP Software Update 24
1.3.4 Automatic software update by ACA 25
1.4 Port Configuration 26
1.5 Power over ETHERNET 28
1.6 Loading/Saving the Configuration 30
1.6.1 Loading the configuration 31
1.6.2 Saving the Configuration 31
1.6.3 URL 32
1.6.4 Deleting a configuration 32
1.6.5 Using the AutoConfiguration Adapter (ACA) 33
1.6.6 Canceling a configuration change 34
1.7 Restart 36
2 Security 39
2.1 Password / SNMPv3 access 40
2.2 SNMPv1/v2 Access Settings 42
2.3 Telnet/Web Access 45
2.3.1 Description of Telnet Access 46
2.3.2 Description of Web Access 46
2.4 Restricted Management Access 47
2.5 Port Security 50

Contents
4RM Web
Release 6.0 07/2010
3Time 53
3.1 SNTP configuration 55
3.2 PTP (IEEE 1588) 59
3.2.1 PTP Global (MS20/MS30, PowerMICE, MACH 104,
MACH 1040) 60
3.2.2 PTP Version 1 (MS20/MS30, PowerMICE,
MACH 104, MACH 1040) 64
3.2.3 PTP Version 2 (BC) (MS20/MS30, PowerMICE,
MACH 104, MACH 1040) 66
3.2.4 PTP Version 2 (TC) (MS20/MS30, PowerMICE) 71
4 Switching 75
4.1 Switching Global 76
4.2 Filters for MAC addresses 80
4.3 Rate Limiter 82
4.3.1 Rate Limiter settings 82
4.4 Multicasts 85
4.4.1 IGMP (Internet Group Management Protocol) 85
4.5 VLAN 93
4.5.1 VLAN Global 93
4.5.2 Current VLAN 96
4.5.3 VLAN Static 98
4.5.4 VLAN Port 100
5 QoS/Priority 103
5.1 Global 104
5.2 Port Configuration 107
5.2.1 Entering the port priority 108
5.3 802.1D/p mapping 109
5.4 IP DSCP mapping 111
6 Redundancy 113
6.1 Ring Redundancy 114
6.1.1 Configuring the HIPER-Ring 116
6.1.2 Configuring the MRP-Ring 120
6.2 Ring/Network Coupling 123
6.2.1 Preparing a Ring/Network coupling 123

Contents
RM Web L2E
Release 6.0 07/2010 5
6.3 Spanning Tree 130
6.3.1 Global 132
6.3.2 Port 138
7 Advanced 147
7.1 DHCP Relay Agent 148
7.2 Industrial Protocols 150
7.2.1 PROFINET IO 150
7.2.2 EtherNet/IP 152
7.3 Command Line 153
8 Diagnostics 155
8.1 Syslog 156
8.2 Event Log 161
8.3 Ports 162
8.3.1 Statistics table 162
8.3.2 Utilization 163
8.3.3 SFP modules 164
8.4 Topology Discovery 165
8.5 Port Mirroring 167
8.6 Device Status 169
8.7 Signal contact 172
8.7.1 Manual setting 172
8.7.2 Function monitoring 172
8.7.3 Device status 174
8.7.4 Configuring traps 174
8.8 Alarms (Traps) 176
8.9 Report 179
8.10 IP address conflict detection 181
8.11 Self Test 183
8.12 Service mode 184
8.12.1 Activating the service mode 185

Contents
6RM Web
Release 6.0 07/2010
8.12.2 Deactivating the service mode 186
A Appendix 189
B Readers’ Comments 197
C Index 199
D Further Support 203

About this Manual
RM Web L2E
Release 6.0 07/2010 7
About this Manual
The "Web-based Interface" reference manual contains detailed information
on using the Web interface to operate the individual functions of the device.
The "Command Line Interface" reference manual contains detailed
information on using the Command Line Interface to operate the individual
functions of the device.
The “Installation” user manual contains a device description, safety
instructions, a description of the display, and the other information that you
need to install the device.
The “Basic Configuration” user manual contains the information you need to
start operating the device. It takes you step by step from the first startup
operation through to the basic settings for operation in your environment.
The “Industry Protocols” user manual describes how the device is connected
by means of a communication protocol commonly used in the industry, such
as EtherNet/IP or PROFINET IO.
The Network Management Software HiVision/Industrial HiVision provides
you with additional options for smooth configuration and monitoring:
XConfiguration of multiple devices simultaneously.
XGraphical interface with network layouts.
XAuto-topology discovery.
XEvent log.
XEvent handling.
XClient / Server structure.
XBrowser interface
XActiveX control for SCADA integration
XSNMP/OPC gateway

About this Manual
8RM Web
Release 6.0 07/2010

Key
RM Web L2E
Release 6.0 07/2010 9
Key
The designations used in this manual have the following meanings:
Symbols used:
XList
Work step
Subheading
Link Indicates a cross-reference with a stored link
Note: A note emphasizes an important fact or draws your
attention to a dependency.
Courier ASCII representation in user interface
WLAN access point
Router with firewall
Switch with firewall
Router
Switch
Bridge

Key
10 RM Web
Release 6.0 07/2010
Hub
A random computer
Configuration Computer
Server
PLC -
Programmable logic
controller
I/O -
Robot

Opening the Web-based Interface
RM Web L2E
Release 6.0 07/2010 11
Opening the Web-based Interface
To open the Web-based interface, you need a Web browser (a program that
can read hypertext), for example Mozilla Firefox version 1 or later, or
Microsoft Internet Explorer version 6 or later.
Note: The Web-based interface uses Java software 6 (“Java™ Runtime
Environment Version 1.6.x”).
Install the software from the enclosed CD-ROM. To do this, you go to
“Additional Software”, select Java Runtime Environment and click on
“Installation”.
Figure 1: Installing Java
Start your Web browser.
Check that you have activated JavaScript and Java in your browser
settings.
Establish the connection by entering the IP address of the device which
you want to administer via the Web-based management in the address
field of the Web browser. Enter the address in the following form:
http://xxx.xxx.xxx.xxx

Opening the Web-based Interface
12 RM Web
Release 6.0 07/2010
The login window appears on the screen.
Figure 2: Login window
Select the desired language.
In the drop-down menu "Login", you select
– user, to have read access, or
– admin, to have read and write access
to the device.
The password “public”, with which you have read access for the login
"user", is preset in the password field. If you wish to have write access to
the device, use the login "admin", select the contents of the password field
and overwrite it with the password “private” (default setting).
Click on OK.
The Web site of the device appears on the screen.

Opening the Web-based Interface
RM Web L2E
Release 6.0 07/2010 13
Note: The changes you make in the dialogs will be copied to the device when
you click “Set”. Click “Reload” to update the display.
To save any changes made so that they will be retained after a power cycle
or reboot of the device use the save option on the "Load/Save" dialog (see
on page 30 “Loading/Saving the Configuration“)
Note: You can block your access to the device by entering an incorrect
configuration.
Activating the function “Cancel configuration change” in the “Load/Save”
dialog enables you to return automatically to the last configuration after a set
time period has elapsed. This gives you back your access to the device.
Figure 3: Website of the device with speech-bubble help

Opening the Web-based Interface
14 RM Web
Release 6.0 07/2010
The menu section displays the menu items. By placing the mouse pointer in
the menu section and clicking the alternate mouse button you can use “Back”
to return to a menu item you have already selected, or “Forward” to jump to
a menu item you have already selected.

Basic Settings
RM Web L2E
Release 6.0 07/2010 15
1 Basic Settings
The Basic Settings menu contains the dialogs, displays and tables for the
basic configuration:
XSystem
XNetwork
XSoftware
XPort configuration
XPower over Ethernet
XLoad/Save
XRestart

Basic Settings
16
1.1 System
RM Web
Release 6.0 07/2010
1.1 System
The “System“ submenu in the basic settings menu is structured as follows:
XDevice Status
XSystem data
XDevice view
XReloading data
Figure 4: "System" Submenu
Device Status
This section of the website provides information on the device status and
the alarm states the device has detected.

Basic Settings
RM Web L2E
Release 6.0 07/2010
1.1 System
17
Figure 5: Device status and display of detected alarms
1 - Symbol indicates the Device Status
2 - Cause of the oldest existing alarm detected
3 - Time of the oldest existing alarm detected
System Data
This area of the website displays the system parameters of the device.
Here you can change
– the system name,
– the location description,
– the name of the contact person for this device,
– the availability of the media modules (see fig. 6)
– the temperature threshold values.
Name Meaning
Name System name of this device
Location Location of this device
Contact The contact for this device
Basic module Hardware version of the device
Media module 1 Hardware version of media module 1
Media module 2 Hardware version of media module 2
Media module 3 Hardware version of media module 3
Media module 4 Hardware version of media module 4
Media module 5 Hardware version of media module 5
Media module 6 Hardware version of media module 6
Media module 7 Hardware version of media module 7
Power supply (P1/P2) Status of power units (P1/P2)
Uptime Time that has elapsed since this device was last restarted.
Temperature Temperature of the device. Lower/upper temperature
threshold values. If the temperature goes outside this range,
the device generates an alarm.
Table 1: System Data
132

Basic Settings
18
1.1 System
RM Web
Release 6.0 07/2010
Figure 6: Availability of the media modules
1 - Module present
2 - Empty slot
3 - Module was removed. Click this check mark to define this slot as an
empty slot.
Device View
The device view shows the device with the current configuration. The
symbols underneath the device view represent the status of the individual
ports.
123

Basic Settings
RM Web L2E
Release 6.0 07/2010
1.1 System
19
Figure 7: Device View
Meaning of the symbols:
The port (10, 100 Mbit/s, 1, 10 Gbit/s) is enabled
and the connection is OK.
The port is disabled by the management
and it has a connection.
The port is disabled by the management
and it has no connection.
The port is in autonegotiation mode.
The port is in HDX mode.
The port is in RSTP discarding mode (100 Mbit/s).
The port is in routing mode (100 Mbit/s).
Updating
This area of the website at the bottom left displays the countdown time
until the applet requests the current data of this dialog again. Clicking the
"Reload" button calls the current dialog information immediately.
The applet polls the current data of the device automatically every
100 seconds.

Basic Settings
20
1.1 System
RM Web
Release 6.0 07/2010
Figure 8: Time until update