Hirschmann RSP 20 User manual

Installation RSP 20/25/30/35
Release 08 08/2014
Technical support
https://hirschmann-support.belden.eu.com
User Manual
Installation
Industrial Ethernet Rail Switch Power
RSP 20/25/30/35

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2014 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. For devices with embedded software, the end-user license agreement on the
enclosed CD/DVD applies.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Printed in Germany
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
Installation RSP 20/25/30/35 039 792-001-08-0814 - 07.08.2014

Installation RSP 20/25/30/35
Release 08 08/2014 3
Contents
Safety instructions 5
About this manual 11
Key 11
1 Description 12
1.1 General description 12
1.2 Device name and product code 13
1.3 Combination options 16
1.4 Device views 17
1.4.1 Front view 17
1.4.2 Rear view 18
1.5 Power supply 18
1.5.1 Working voltage characteristic value K9 18
1.5.2 Working voltage with the characteristic value KK 18
1.5.3 Working voltage characteristic value CC 19
1.6 Ethernet ports 19
1.6.1 10/100 Mbit/s twisted pair port 19
1.6.2 100/1000 Mbit/s twisted pair port (optional) 20
1.6.3 100 Mbit/s F/O port 20
1.6.4 100/1000 Mbit/s F/O port (optional) 20
1.7 Display elements 21
1.7.1 Device state 21
1.7.2 Port state 22
1.8 Management interfaces 23
1.8.1 V.24 interface (external management) 23
1.8.2 SD card interface 23
1.9 Signal contact 24
2 Installation 25
2.1 Checking the package contents 25
2.2 Installing the SD card (optional) 25
2.3 Installing and grounding the device 26
2.3.1 Installing the device onto the DIN rail 26
2.3.2 Grounding the device 27
2.4 Installing an SFP transceiver (optional) 28
2.5 Connecting the terminal blocks 28

4Installation RSP 20/25/30/35
Release 08 08/2014
2.5.1 Working voltage characteristic value K9 29
2.5.2 Working voltage with the characteristic value KK 30
2.5.3 Working voltage characteristic value CC 31
2.5.4 Signal contact 32
2.6 Operating the device 32
2.7 Connecting data cables 33
2.8 Filling out the inscription label 33
3 Making basic settings 34
4 Upgrading Software 35
5 Monitoring the ambient air temperature 36
6 Maintenance and service 37
7Disassembly 38
7.1 Removing the device 38
7.2 Removing an SFP transceiver (optional) 39
8 Technical data 40
A Further Support 51

Installation RSP 20/25/30/35
Release 08 08/2014 5
Safety instructions
General safety instructions
You operate this device with electricity. The proper and safe operation of
this device depends on proper handling during transportation, proper
storage and assembly, and conscientious operation and maintenance
procedures. Improper use of this device is associated with the risk of
personal injury or property damage.
Read this documentation as well as the safety instructions and warn-
ings before connecting any cables.
Never start operation with damaged components.
The device does not contain any service components. If the device is
not functioning correctly, or if it is damaged, turn off the power supply
and return the device to Hirschmann for inspection.
Qualification requirements for personnel
Only allow qualified personnel to work on the device.
Qualified personnel have the following characteristics:
Qualified personnel are properly trained. Training as well as practical
knowledge and experience make up their qualifications. This is the
prerequisite for grounding and labeling circuits, devices, and systems
in accordance with current standards in safety technology.
Qualified personnel are aware of the dangers that exist in their work.
Qualified personnel are familiar with appropriate measures against
these hazards in order to reduce the risk for themselves and others.
Qualified personnel receive training on a regular basis.
Certified usage
Use the device solely for the application cases described in the
Hirschmann product information, including this manual.
Operate the device solely according to the technical specifications.
See “Technical data” on page 40.
WARNING
UNCONTROLLED MACHINE ACTIONS
To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

6Installation RSP 20/25/30/35
Release 08 08/2014
National and international safety regulations
Verify that the electrical installation meets local or nationally applicable
safety regulations.
Grounding the device
Grounding the device is by means of a separate ground connection on the
device.
Ground the device before connecting any other cables.
Disconnect the grounding only after disconnecting all other cables.
The overall shield of a connected shielded twisted pair cable is connected
to the ground connector on the front panel as a conductor.
Working voltage
The working voltage is connected to the chassis through protective
elements exclusively.
Connect only a working voltage that corresponds to the type plate of
your device.
Only for device variants featuring working voltage with the character-
istic value K9 or KK:
See “Device name and product code” on page 13.
Every time you connect the electrical conductors, make sure that the
following requirements are met:
The power supply conforms to overvoltage category I or II.
The power supply has an easily accessible disconnecting device
(e.g., a switch or a plug). This disconnecting device is clearly iden-
tified. So in the case of an emergency, it is clear which discon-
necting device belongs to which power supply cable.
The electrical wires are voltage-free.
Supply with DC voltage:
A fuse suitable for DC voltage is located in the plus conductor of the
power supply.
The minus conductor is on ground potential. Otherwise, a fuse is
also located in the minus conductor.
Regarding the properties of this fuse: See “General technical data”
on page 40.
Supply with AC voltage:
A fuse is located in the outer conductor of the power supply.
The neutral conductor is on ground potential. Otherwise, a fuse is
also located in the neutral conductor.
Regarding the properties of this fuse: See “General technical data”
on page 40.
Supply with AC voltage:
The wire diameter of the power supply cable is at least 0.75 mm²
(North America: AWG18) on the working voltage input.

Installation RSP 20/25/30/35
Release 08 08/2014 7
Supply with DC voltage:
The wire diameter of the power supply cable is at least 1 mm²
(North America: AWG16) on the working voltage input.
The cross-section of the protective conductor is the same size as
or bigger than the cross-section of the power supply cables.
The power supply cables used are permitted for the temperature
range required by the application case.
Relevant for North America:
The power cords are suitable for ambient air temperatures of at
least 167 °F (75 °C). The power cord wires are made of copper.
Start connecting the electrical wires only if all the above safety require-
ments are fulfilled.
Solely for device variants with the characteristic value CC for the
working voltage:
See “Device name and product code” on page 13.
Every time you connect the electrical conductors, make sure that the
following requirements are met:
The power supply is Class 2 compliant.
The power supply conforms to overvoltage category I or II.
The working voltage inputs are designed for operation with safety
extra-low voltage. Connect only SELV circuits with voltage restric-
tions in line with IEC/EN 60950-1 to the working voltage connec-
tions.
The power supply has an easily accessible disconnecting device
(e.g., a switch or a plug). This disconnecting device is clearly iden-
tified. So in the case of an emergency, it is clear which discon-
necting device belongs to which power supply cable.
The electrical wires are voltage-free.
A fuse suitable for DC voltage is located in the plus conductor of the
power supply.
The minus conductor is on ground potential. Otherwise, a fuse is
also located in the minus conductor.
Regarding the properties of this fuse: See “General technical data”
on page 40.
The wire diameter of the power supply cable is at least 1 mm²
(North America: AWG16) on the working voltage input.
The cross-section of the ground conductor is the same size as or
bigger than the cross-section of the power supply cables.

8Installation RSP 20/25/30/35
Release 08 08/2014
The power supply cables used are permitted for the temperature
range required by the application case.
Relevant for North America:
The power cords are suitable for ambient air temperatures of at
least 167 °F (75 °C). The power cord wires are made of copper.
Start connecting the electrical wires only if all the above safety require-
ments are fulfilled.
Internal fuses are triggered solely in the case of a detected error in the
device. In case of damage or malfunction of the device, turn off the
working voltage and return the device to the plant for inspection.
For operating voltage connections with a protective conductor connec-
tion: connect the protective conductor before connecting the conduc-
tors for the operating voltage.
Only switch on the operating voltage for the device when the following
requirements are fulfilled:
The housing is closed
The terminal blocks are wired correctly
The terminal blocks for the operating supply are connected
Signal contact
For the signal contact to be connected, make sure the following require-
ments are met:
The device is grounded.
The signal contact connection wires are voltage-free.
The connected voltage is limited by a current limitation device or a
fuse.
Observe the electrical threshold values for the signal contact.
See “General technical data” on page 40.
Start connecting the signal contact solely if all the above requirements are
fulfilled.
Installation site requirements
Install the device in a fire protected enclosure according to
EN 60950-1.
Only for device variants featuring working voltage with the character-
istic value K9 or KK:
See “Device name and product code” on page 13.
Install this device solely in a switch cabinet or in an operating site with
restricted access, to which maintenance staff have exclusive access.

Installation RSP 20/25/30/35
Release 08 08/2014 9
Housing
Only technicians authorized by the manufacturer are permitted to open
the housing.
Never insert pointed objects (narrow screwdrivers, wires, etc.) into the
device or into the connection terminals for electric conductors. Do not
touch the connection terminals.
Keep the ventilation slits free to ensure good air circulation.
Install the device in the vertical position.
At ambient temperatures > 140 °F (60 °C):
The surfaces of the device housing may become hot. Avoid touching
the device while it is operating.
CE marking
The labeled devices comply with the regulations contained in the following
European directive(s):
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
The product can be used in the industrial sector.
Interference immunity: EN 61000-6-2
Emitted interference: EN 55022
Reliability: EN 60950-1
You find more information on technical and industry standards here:
“Technical data” on page 40
Device variant Directive
All variants 2004/108/EC (EMC)
Directive of the European Parliament and the council for stan-
dardizing the regulations of member states with regard to elec-
tromagnetic compatibility.
2011/65/EU (RoHS)
Directive of the European Parliament and of the Council on the
restriction of the use of certain hazardous substances in elec-
trical and electronic equipment.
Only for device variants
featuring working voltage with
the characteristic value K9 or
KK:
2006/95/EC
Directive of the European Parliament and the council for stan-
dardizing the regulations of member states with regard to elec-
trical equipment to be used within specific voltage ranges.

10 Installation RSP 20/25/30/35
Release 08 08/2014
Warning! This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to take appro-
priate measures.
Note: The assembly guidelines provided in these instructions must be
strictly adhered to in order to observe the EMC threshold values.
LED or laser components
LED or LASER components according to IEC 60825-1 (2007):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT
FCC note:
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference; (2) this device must accept any interference received,
including interference that may cause undesired operation.
Appropriate testing has established that this device fulfills the require-
ments of a class A digital device in line with part 15 of the FCC regula-
tions.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can also radiate these
frequencies. If it is not installed and used in accordance with this oper-
ating manual, it can cause radio transmission interference. The use of this
device in a residential area can also cause interference, and in this case
the user is obliged to cover the costs of removing the interference.
Recycling note
After usage, this device must be disposed of properly as electronic waste,
in accordance with the current disposal regulations of your county, state,
and country.

Installation RSP 20/25/30/35
Release 08 08/2014 11
About this manual
The “Installation” user manual contains a device description, safety instruc-
tions, a description of the display, and the other information that you need to
install the device.
The following manuals are available as PDF files on the CD/DVD supplied:
Installation user manual
Basic Configuration user manual
Redundancy Configuration user manual
Reference manual for the graphical user interface
Command Line Interface user manual
The Industrial HiVision network management software provides you with
additional options for smooth configuration and monitoring:
ActiveX control for SCADA integration
Auto-topology discovery
Browser interface
Client/server structure
Event handling
Event log
Simultaneous configuration of multiple devices
Graphical user interface with network layout
SNMP/OPC gateway
Key
The symbols used in this manual have the following meanings:
Listing
Work step
Subheading

12 Installation RSP 20/25/30/35
Release 08 08/2014
1 Description
1.1 General description
You can choose from between a wide range of variants. You have the option
to set up your device individually based on different criteria:
Number of ports
Transmission speed
Types of connectors
Temperature range
Working voltage range
Certifications
Redundancy functions
The RSP 20/25/30/35 devices are designed for the special requirements of
industrial automation. They meet the relevant industry standards, provide
very high operational reliability, even under extreme conditions, and also
long-term reliability and flexibility.
The devices work without a fan.
The device is mounted by latching in place on a hat rail.
You have the option of choosing various media to connect to the terminal
devices and other network components:
Multimode optical fiber
Singlemode optical fiber
Twisted pair cable
The redundancy concept allows the network to be reconfigured quickly.
There are convenient options for managing the device. Administer your
devices via:
a Web browser
SSH
Telnet
HiDiscovery (Software for putting the device into operation)
Network management software (e.g. Industrial HiVision)
a V.24 interface (locally on the device)
The devices provide you with a large range of functions, which the manuals
for the operating software inform you about. You will find these manuals as
PDF files on the enclosed CD/DVD, or you can download them from the
Internet on the Hirschmann product pages (www.hirschmann.com).
The Hirschmann network components help you ensure continuous commu-
nication across all levels of the company.

Installation RSP 20/25/30/35
Release 08 08/2014 13
1.2 Device name and product code
The device name corresponds to the product code. The product code is
made up of characteristics with defined positions. The characteristic values
stand for specific product properties.
Item Characteristic Charac-
teristic
value
Description
1 ... 5 Product RSP20 Fast Ethernet switch
RSP25 Fast Ethernet switch with extended redundancy
function
RSP30 Gigabit Ethernet switch
RSP35 Gigabit Ethernet switch with extended redundancy
function
6 (hyphen) –
7 ... 8 Number
Fast Ethernet ports
08 8 ×
11 11 ×
9 ... 10 Number
Gigabit Ethernet ports
00 0 ×
03 3 ×
11 ... 13 Configuration of the
uplink ports
3Z6 3 × SFP slot for 100 Mbit/s connections
twisted pair and F/O
3O6 3 × SFP slot for 100/1000 Mbit/s connections
twisted pair and F/O
14 ... 15 Configuration of the
other ports
TT 8 × RJ45 socket for 10/100 Mbit/s twisted pair
connections
ZT 4 × RJ45 socket for 10/100 Mbit/s twisted pair
connections
4 × SFP slot for 100 Mbit/s connections
twisted pair and F/O
16 (hyphen) –
17 Temperature range S Standard 0 °C ... +60 °C (+32 °F ...
+140 °F)
T Extended −40 °F ... +158 °F (−40 °C ...
+70 °C)
E Extended with
conformal coating
−40 °F ... +158 °F (−40 °C ...
+70 °C)
18 ... 19 Working voltage CC 2 voltage inputs for redundant power supply
Rated voltage range DC
24 V ... 48 V
K9 1 voltage input
Rated voltage range AC
110 V ... 230 V, 50 Hz ... 60 Hz
Rated voltage range DC
60 V ... 250 V
KK 2 voltage inputs for redundant power supply
Rated voltage range AC
110 V ... 230 V, 50 Hz ... 60 Hz
Rated voltage range DC
60 V ... 250 V
Table 1: Device name and product code

14 Installation RSP 20/25/30/35
Release 08 08/2014
20 ... 21 Certificates and decla-
rations
You will find detailed information on the certificates and decla-
rations applying to your device in a separate overview.
See table 2 on page 14.
22 ... 23 Customer-specific
version
HS Hirschmann Standard
HM Hirschmann Fast MRP
HP Hirschmann PRP
HH Hirschmann HSR
Note: The following redundancy functions are interchange-
able with each other:
HM
HP
HH
24 Software configura-
tion
E Entry (without configuration)
25 ... 26 Software level 2S HiOS Layer 2 Standard
2A HiOS Layer 2 Advanced
3S HiOS Layer 3 Standard
27 ... 31 Software version 02.0. Software version 02.0
XX.X. Current software version
Application case Certificates and
declarations
Characteristic valuea
a. X = Certificate or declaration present
(X) = Certificate or declaration in preparation
(x) = Certificate or declaration available upon request
V9 VY Y9 Z9
Standard applications CE XXXX
FCC XXXX
EN60950-1 XXXX
EN61131-2 XXXX
UL 508 X X
Substation applications IEC 61850-3 X X
IEEE 1613 X X
Table 2: Assignment: application cases, certificates and declarations, character-
istic values
Item Characteristic Charac-
teristic
value
Description
Table 1: Device name and product code

Installation RSP 20/25/30/35 Release
08
08/2014 15
Table 3: Sample product code RSP20-11003Z6TT-SCCZ9HSE2SXX.X.
3RVLWLRQ
563
  =
77
6
=
&&










3URGXNW5DLO6ZLWFK3RZHU
'HVFULSWLRQ
1XPEHURI0ELWVSRUWV
1XPEHURI0ELWVSRUWV
&RQILJXUDWLRQRIWKHXSOLQNSRUWVî6)3VORWIRU0ELWV)273
&RQILJXUDWLRQRIWKHRWKHUSRUWVî5-VRFNHWIRU0ELWV73
&XVWRPHUVSHFLILFYHUVLRQ+LUVFKPDQQVWDQGDUG
7HPSHUDWXUHUDQJH6WDQGDUG))&&
:RUNLQJYROWDJHYROWDJHLQSXWV9'&9'&
&HUWLILFDWHVDQGGHFODUDWLRQV&()&&(1(1
+6

²
²

 )DVW(WKHUQHW
 6RIWZDUHFRQILJXUDWLRQ(QWU\ZLWKRXWFRQILJXUDWLRQ

6
(;;;
 6RIWZDUHOHYHO+L26/D\HU6WDQGDUG
 6RIWZDUHYHUVLRQ&XUUHQWVRIWZDUHYHUVLRQ

16 Installation RSP 20/25/30/35
Release
08
08/2014
1.3 Combination options
Item 1 ... 3 4 ... 5 67 ... 8 9 ... 10 11 ... 13 14 ... 15 16 17 18 ... 19 20 ... 21 22 ... 23 24 25 ... 26
Charac-
teristic
Product Data rate
and hard-
ware type
Number
Fast
Ethernet
ports
Number
Gigabit
Ethernet
ports
Configu-
ration of
the
uplink
ports
Configu-
ration of
the other
ports
Temper
ature
range
Working
voltage
Certificates
and declara-
tions
Customer-
specific
version
Soft-
ware
configu-
ration
Software
level
Charac-
teristic
value
RSP 20 – 11 00 3Z6 TT; ZT – S; T; E CC; K9; KK Z9; Y9; V9; VY HS E 2A; 2S; 3S
25 – 11 00 3Z6 TT; ZT – S; T; E CC; K9; KK Z9; Y9; V9; VY HM; HP; HH E 2A; 2S; 3S
30 – 08 03 3O6 TT; ZT – S; T; E CC; K9; KK Z9; Y9; V9; VY HS E 2A; 2S; 3S
35 – 08 03 3O6 TT; ZT – S; T; E CC; K9; KK Z9; Y9; V9; VY HM; HP; HH E 2A; 2S; 3S
Table 4: Combination options of the RSP 20/25/30/35 device variants

Installation RSP 20/25/30/35
Release 08 08/2014 17
1.4 Device views
1.4.1 Front view
1 LED display elements for device status
2 V.24 interface
3 3 × SFP slot for 100 Mbit/s connections
4 8 × 10/100 Mbit/s twisted pair ports
5 Grounding screw
6 Working voltage connection
alternatively,
depending on
device variant
Operating voltage
characteristic value:
CC
2 voltage inputs for redundant power supply
2-pin terminal block
Operating voltage
characteristic value:
K9
1 voltage input
3-pin terminal block
Operating voltage
characteristic value:
KK
2 voltage inputs for redundant power supply
3-pin terminal block
7 Connection for the signal contact
Table 5: Front view (using the example RSP20-11003Z6TT-SCC...)
6
7
4
5
1
2
3

18 Installation RSP 20/25/30/35
Release 08 08/2014
1.4.2 Rear view
1.5 Power supply
You will find information on the characteristic values here:
“Device name and product code” on page 13
1.5.1 Working voltage characteristic value K9
For the power supply of the device, a 3-pin terminal block is available.
For further information see “Working voltage characteristic value K9” on
page 29.
1.5.2 Working voltage with the characteristic value KK
For the redundant power supply of the device, two 3-pin terminal blocks are
available.
For further information see “Working voltage with the characteristic value KK”
on page 30.
1 Slot for the SD card
2 Knurled screw
1
2

Installation RSP 20/25/30/35
Release 08 08/2014 19
1.5.3 Working voltage characteristic value CC
For the redundant power supply of the device, two 2-pin terminal blocks are
available.
For further information see “Working voltage characteristic value CC” on
page 31.
1.6 Ethernet ports
You can connect end devices and other segments to the device ports using
twisted pair cables or optical fibers (F/O).
1.6.1 10/100 Mbit/s twisted pair port
This port is an RJ45 socket.
See table 5 on page 17.
The 10/100 Mbit/s twisted pair port offers you the ability to connect network
components according to the IEEE 802.3 10BASE-T/100BASE-TX standard.
This port supports:
Autonegotiation
Autopolarity
Autocrossing (if autonegotiation is activated)
100 Mbit/s half-duplex mode, 100 Mbit/s full duplex mode
10 Mbit/s half-duplex mode, 10 Mbit/s full duplex mode
Delivery state: autonegotiation active
The socket housing is electrically connected with the front panel.
Pin Function
1 RD+ Receive path
2RD−Receive path
3 TD+ Transmission path
6TD−Transmission path
4,5,7,8 —
Table 6: Pin assignment of the 10/100 Mbit/ twisted pair port, RJ-45 socket, MDI-X
mode
1
2
3
4
5
6
7
8

20 Installation RSP 20/25/30/35
Release 08 08/2014
1.6.2 100/1000 Mbit/s twisted pair port (optional)
This port is an SFP slot.
The 100/1000-Mbit/s twisted pair port offers you the possibility to connect
network components according to the IEEE 802.3 100BASE-FX/1000BASE-
SX/1000BASE-LX standard.
This port supports:
Autonegotiation
Full duplex mode
1.6.3 100 Mbit/s F/O port
This port is an SFP slot.
The 100 Mbit/s F/O port offers you the ability to connect network components
according to the IEEE 802.3 100BASE-FX standard.
This port supports:
100 Mbit/s half-duplex mode, 100 Mbit/s full duplex mode
Default setting: Full duplex
1.6.4 100/1000 Mbit/s F/O port (optional)
This port is an SFP slot.
The 100/1000 Mbit/s F/O port offers you the ability to connect network
components according to the IEEE 802.3 100BASE-FX/1000BASE-
SX/1000BASE-LX standard.
This port supports:
1000 Mbit/s full duplex
100 Mbit/s half-duplex mode, 100 Mbit/s full duplex mode
State on delivery:
100 Mbit/s full duplex when using a Fast Ethernet SFP transceiver
1000 Mbit/s full duplex when using a Gigabit Ethernet SFP transceiver
Pin Function
1BI_DB+
2BI_DB−
3BI_DA+
4 BI_DD+
5BI_DD−
6BI_DA−
7 BI_DC+
8BI_DC−
Table 7: Pin assignment of the 10/100/1000 Mbit/s twisted pair port, RJ45 socket,
1000 Mbit/s mode, MDI-X mode
1
2
3
4
5
6
7
8