Kramer VP-440 User manual

P/N: 2900-300476 Rev 11 www.kramerAV.com
USER MANUAL
MODEL:
VP-440
Presentation Switcher/Scaler

Kramer Electronics Ltd.
VP-440 –Contents
i
Contents
Introduction 1
Getting Started 1
Overview 2
Defining the VP-440 Presentation Switcher/Scaler 4
Mounting VP-440 6
Connecting the VP-440 7
Microphone Pinout 8
Wiring the TP LINE OUT RJ-45 Connector 9
Connecting the VP-440 via the INPUT SELECT Terminal Block Connector 10
Connecting to the VP-440 via RS-232 11
Operating the VP-440 12
Using the Front Panel buttons 12
Using the OSD Menu 14
Operating via Ethernet 17
Using the Embedded Web Pages 20
Loading and Saving Configurations 22
Entering Standby Mode 22
Configuring Video Input Settings 23
Selecting the Input to be Switched to the Outputs 24
Freezing or Clearing the Video Output 24
Adjusting Microphone and Output Volume 24
Configuring Network Settings 25
Upgrading the Firmware 26
Configuring Video Output Settings 27
Configuring HDCP per Input/Output 28
Managing EDID 29
Adjusting Audio Input Settings 30
Adjusting Microphone Settings 31
Configuring Automatic Switching Settings 32
Defining Panel Lock Button 33
Defining Freeze Button Behavior 33
Controlling VP-440 via the RS-232 Terminal Block Connectors 34
Controlling an External Device via the RS-232 Terminal Block Connectors 35
Securing the Web Pages with a Password 36
Viewing the About Page 38
Technical Specifications 39
Default Communication Parameters 40
Input Resolutions 41
Output Resolutions 41
Protocol 3000 42
Understanding Protocol 3000 43
Kramer Protocol 3000 Syntax 44
Protocol 3000 Commands 44

Kramer Electronics Ltd.
VP-440 –Introduction
1
Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world
of unique, creative, and affordable solutions to the vast range of problems that confront the
video, audio, presentation, and broadcasting professional on a daily basis. In recent years, we
have redesigned and upgraded most of our line, making the best even better!
Getting Started
We recommend that you:
•Unpack the equipment carefully and save the original box and packaging materials for
possible future shipment.
•Review the contents of this user manual.
Go to www.kramerav.com/downloads/VP-440 to check for up-to-date user manuals,
application programs, and to check if firmware upgrades are available (where appropriate).
Achieving the Best Performance
•Use only good quality connection cables (we recommend Kramer high-performance,
high-resolution cables) to avoid interference, deterioration in signal quality due to poor
matching, and elevated noise levels (often associated with low quality cables).
•Do not secure the cables in tight bundles or roll the slack into tight coils.
•Avoid interference from neighboring electrical appliances that may adversely influence
signal quality.
•Position your Kramer VP-440 away from moisture, excessive sunlight and dust.
This equipment is to be used only inside a building. It may only be connected to other
equipment that is installed inside a building.
Safety Instructions
Caution: There are no operator serviceable parts inside the unit.
Warning: Use only the power cord that is supplied with the unit.
Warning: Disconnect the power and unplug the unit from the wall before installing.
Recycling Kramer Products
The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to reduce
the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected
and recycled. To comply with the WEEE Directive, Kramer Electronics has made
arrangements with the European Advanced Recycling Network (EARN) and will cover any
costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on

Kramer Electronics Ltd.
VP-440 –Introduction
2
arrival at the EARN facility. For details of Kramer’s recycling arrangements in your particular
country go to our recycling pages at www.kramerav.com/support/recycling.
Overview
The VP-440 is a high-performance presentation scaler/switcher for HDMI™and computer
graphics signals. The unit scales the video, embeds the audio, and outputs the signal to both
an HDMI and an HDBaseT output, as well as outputting to unbalanced stereo audio.
The VP-440 features:
•PixPerfect™scaling technology –Kramer’s precision pixel mapping and high-quality
scaling technology, with full up and down scaling of all video input signals.
•HDTV compatibility.
•HDCP compliance.
•Automatic input switching selectable to last connected or auto-scan.
•6 video inputs –4 HDMI on HDMI connectors, 2 computer graphics video on 15-pin HD
connectors.
•Scaled output on HDMI and HDBT connectors simultaneously.
•System Range for the HDBT inputs and outputs –Up to 70m (230ft).
For optimum range and performance using HDBaseT™, use recommended Kramer cables,
available at www.kramerav.com/product/VP-440.
•Up to UXGA/1080p output resolutions.
•Microphone input with audio DSP options including mixing and talk-over.
•Companion AFV (Audio-Follow-Video) –stereo audio for every video input.
•6 unbalanced stereo inputs on 3.5mm connectors as well as embedded audio for the
HDMI inputs, each with individual level controls.
•Audio outputs –one unbalanced stereo on a 3.5mm connector as well as embedded
audio on the HDMI and HDBT outputs.
•Multiple aspect ratio selections –full, best fit, over scan, under scan, letter box and pan
scan.
•Powerful audio features via DSP technology including audio equalization, mixing, delay
and so on.
•Built-in ProcAmp –color, hue, sharpness, noise, contrast and brightness.
•Supports 4:4:4 (RGB and YUV) as well as 4:2:2 (YUV) color sampling in Native mode.
•Maintains constant output sync –there is no disruption on the output while switching
between inputs and when no video is detected.
•Dedicated RS-232 port for bidirectional data tunneling via HDBT.
•Front panel lockout.
•Non-volatile memory –saves final settings.

Kramer Electronics Ltd.
VP-440 –Introduction
3
Control your VP-440:
•Directly, via the front panel push buttons.
•By RS-232 serial commands transmitted by a touch screen system, PC, or other serial
controller.
•Via the OSD (on-screen display).
•Via remote contact-closure switches.
•Via the Ethernet with built-in Web pages.
Using Twisted Pair Cables for HDBT
Kramer engineers have developed special twisted pair cables to best match our digital twisted
pair products.
For optimum range and performance use the recommended Kramer shielded twisted pair cables
available at www.kramerav.com/product/VP-440.
Typical Applications
VP-440 is ideal for the following typical applications:
•Education –classrooms, lecture theaters.
•Projection systems in conference rooms, boardrooms, hotels and churches.
•Home theater up-scaling.

Kramer Electronics Ltd.
VP-440 –Defining the VP-440 Presentation Switcher/Scaler
4
Defining the VP-440 Presentation
Switcher/Scaler
This section defines the VP-440.
Figure 1: VP-440 Presentation Switcher/Scaler Front Panel
#
Feature
Function
48 V () Slide Switch
Slide up (48V) to select a condenser type microphone; slide down
to select a dynamic type microphone (we recommend that you slide
down if a microphone is not connected to the VP-440).
MIC 6.3mm Jack
Connect to the microphone source.
Input
Selector
Buttons
HDMI IN
Press to select the HDMI input (from 1 to 4).
PC IN
Press to select the computer graphics input (from 1 to 2).
MENU Button
Displays the OSD menu (see Using the OSD Menu on page 14).
Navigation
Buttons

Press to decrease numerical values or select from several
definitions.
When not within the OSD menu mode, press to reduce the output
volume.

Press to move up the menu list values (see Using the OSD Menu
on page 14).

Press to increase numerical values or select from several
definitions.
When not within the OSD menu mode, press to increase the output
volume.

Press to move down the menu list (see Using the OSD Menu
on page 14).
ENTER
Press to accept changes and change the SETUP parameters
(see Using the OSD Menu on page 14).
RESET TO XGA/720p Button
Press to reset the video resolution to XGA or 720p.
Press and hold for about 5 seconds to toggle between switching to
XGA or 720p.
PANEL LOCK Button
Press and hold for about 10 seconds to lock/unlock the front panel
buttons (see Locking the Front Panel Buttons on page 13).
1
2
3
4
5
6
7
8

Kramer Electronics Ltd.
VP-440 –Defining the VP-440 Presentation Switcher/Scaler
5
Figure 2: VP-440 Presentation Switcher/Scaler Rear Panel
#
Feature
Function
VIDEO INPUT
Connectors
HDMI
Connect to the HDMI source (from 1 to 4).
PC 15-pin HD
Connect to the computer graphics source (from 1 to 2).
AUDIO INPUT
Unbalanced Stereo
3.5 Mini Jack
Connector
HDMI
Connect to the analog audio HDMI source (from 1 to 4).
PC
Connect to the analog audio computer graphics source
(from 1 to 2).
AUDIO OUT 3.5 Mini Jack Connector
Connect to an unbalanced stereo audio acceptor.
ETHERNET Connector
Connects to the PC or other controller through computer
networking.
HDMI OUT Connector
Connect to the HDMI acceptor.
HDBT RJ-45 Port
Connect to an HDBT receiver.
INPUT SELECT Terminal Block
Connectors
For remotely switching the inputs via contact closure
switches.
DATA (Tx, Rx, GND) Terminal Block
Connectors
Connect to the PC or control device to tunnel data between
this RS-232 port and the HDBT OUT port.
CTRL (Tx, Rx, GND) Terminal Block
Connectors
Connect to the PC or the serial controller to control the
device or to control an external device (e.g., a monitor).
5V DC/4A
+5V DC connector for powering the unit.
9
10
11
12
13
14
15
16
17
18
19
20

Kramer Electronics Ltd.
VP-440 –Mounting VP-440
6
Mounting VP-440
This section provides instructions for mounting VP-440. Before installing, verify that the
environment is within the recommended range:
•Operation temperature –0to 40C (32 to 104F).
•Storage temperature –-40to +70C (-40 to +158F).
•Humidity –10% to 90%, RHL non-condensing.
Caution:
•Mount VP-440 before connecting any cables or power.
Warning:
•Ensure that the environment (e.g., maximum ambient temperature & air flow) is
compatible for the device.
•Avoid uneven mechanical loading.
•Appropriate consideration of equipment nameplate ratings should be used for avoiding
overloading of the circuits.
•Reliable earthing of rack-mounted equipment should be maintained.
•Maximum mounting height for the device is 2 meters.
Mounting the VP-440 in a Rack
Mount the unit in a rack using the recommended rack adapter
(see www.kramerav.com/product/VP-440).
Mounting the VP-440 on a Table or Shelf
Attach the rubber feet and place the unit on a flat surface.
For more information go to www.kramerav.com/downloads/VP-440.

Kramer Electronics Ltd.
VP-440 –Connecting the VP-440
7
Connecting the VP-440
Always switch off the power to each device before connecting it to your VP-440. After
connecting your VP-440, connect its power and then switch on the power to each device.
You do not have to connect all the inputs and outputs, connect only those that are required.
Figure 3: Connecting the VP-440 Presentation Switcher / Scaler
To connect the VP-440, as illustrated in the example in Figure 3, do the following:
1. Connect an HDMI source (for example, a Blu-ray disk player) to the HDMI 1 (H1) VIDEO
INPUT connector (from 1 to 4).
Alternatively, you can connect the DVI connector on the DVD player to the HDMI
connector on the VP-440 via a DVI-HDMI adapter. When using this adapter, you
can connect the audio signal via the 3.5mm mini jack connector .
2. Connect a computer graphics source to the PC 1 15-pin HD VIDEO INPUT
connector (from 1 to 2).
11
9
10

Kramer Electronics Ltd.
VP-440 –Connecting the VP-440
8
3. Connect the audio input signals to the AUDIO INPUT 3.5mm mini jack connectors &
, as required (not shown in Figure 3).
4. Connect the HDMI OUT connector to an HDMI acceptor (for example, an LCD
display).
5. Connect the HDBT OUT connector to an HDBT receiver.
6. Connect the AUDIO OUT 3.5mm mini jack connector to an unbalanced stereo audio
acceptor (not shown in Figure 3).
7. On the front panel, connect a microphone to the MIC 6.3mm phone jack and set it to
condenser or dynamic type.
8. Connect the power cord (not shown in Figure 3).
Connect the:
▪RS-232 DATA 3-pin terminal block connector (Tx, Rx, G) to a PC for sending RS-
232 commands via HDBT.
▪RS-232 CONTROL 3-pin terminal block connector (Tx, Rx, G) to a PC to control
the device.
9. Connect the INPUT SELECT 7-pin terminal block (contact-closure remote-control pins)
to select an input by momentarily pressing the switch.
10.Connect the ETHERNET port (see Operating via Ethernet on page 17).
Microphone Pinout
The microphone 6.3mm jack pinout for a
condenser microphone.
Figure 4: Condenser Microphone Pinout
The microphone 6.3mm jack pinout for a
Dynamic microphone.
Figure 5: Dynamic Microphone Pinout
11
12
15
16
13
2
20
18
19
17
14