Hirschmann MSM20 User manual

Installation MSM20/22/24/40/42/46/50
Release 09 11/2016
Technical support
https://hirschmann-support.belden.eu.com
User Manual
Installation
MICE Switch Media Modules
MSM20/22/24/40/42/46/50

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2016 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
MSM20/22/24/40/42/46/50

Installation MSM20/22/24/40/42/46/50
Release 09 11/2016 3
Contents
Safety instructions 5
About this manual 15
Key 15
1 Description 16
1.1 General description 16
1.2 Device name and product code 16
1.3 Slots of the basic device 20
1.4 Media modules 22
1.4.1 Media modules MSM20 22
1.4.2 Media modules MSM40 24
1.4.3 PoE-capable media modules MSM22, MSM42 and
MSM46 25
1.5 Media module MSM50 27
1.6 MSM24 I/O module 27
1.7 SFP Transceiver 30
1.8 Ethernet ports 30
1.9 Display elements 33
1.9.1 MSM20 media modules 33
1.9.2 MSM22, MSM42 and MSM46 media modules 34
1.9.3 MSM24 I/O module 35
1.9.4 MSM40 media modules 36
1.9.5 MSM50 media modules 37
2 Installation 38
2.1 Checking the package contents 38
2.2 Installing media modules 38
2.2.1 Device variants featuring customer-specific version
with the characteristic value HH 39
2.2.2 Device variants featuring customer-specific version
with the characteristic value HX, MX 40
2.3 Connecting an I/O module 41
2.3.1 Connecting actuators and sensors 41
2.4 Installing an SFP transceiver (optional) 42
2.5 Connecting data cables 43

4Installation MSM20/22/24/40/42/46/50
Release 09 11/2016
2.5.1 10/100/1000 Mbit/s twisted pair port 43
2.5.2 10/100 Mbit/s twisted pair port 43
2.5.3 1/2.5 Gbit/s F/O port 43
2.5.4 100/1000 Mbit/s F/O port 43
2.5.5 100 Mbit/s F/O port 43
3 Maintenance and service 44
4Disassembly 45
4.1 Removing an SFP transceiver (optional) 45
4.2 Removing a media module 45
4.2.1 Device variants featuring customer-specific version
with the characteristic value HH 45
4.2.2 Device variants featuring customer-specific version
with the characteristic value HX, MX 46
5 Technical data 47
A Further Support 59

Installation MSM20/22/24/40/42/46/50
Release 09 11/2016 5
Safety instructions
General safety instructions
You operate this device with electricity. Improper usage of the device
entails the risk of physical injury or significant property damage. The
proper and safe operation of this device depends on proper handling
during transportation, proper storage and installation, and careful
operation and maintenance procedures.
Before connecting any cable, read this document, and the safety
instructions and warnings.
Operate the device with undamaged components exclusively.
The device is free of any service components. In case of a damaged
or malfunctioning the device, turn off the supply voltage and return the
device to Hirschmann for inspection.
National and international safety regulations
Verify that the electrical installation meets local or nationally applicable
safety regulations.
Certified usage
Use the product only for the application cases described in the
Hirschmann product information, including this manual.
Operate the product only according to the technical specifications.
See “Technical data” on page 47.
Connect to the product only components suitable for the requirements
of the specific application case.
WARNING
UNCONTROLLED MACHINE ACTIONS
To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

6Installation MSM20/22/24/40/42/46/50
Release 09 11/2016
Qualification requirements for personnel
Only allow qualified personnel to work on the device.
Qualified personnel have the following characteristics:
Qualified personnel are properly trained. Training as well as practical
knowledge and experience make up their qualifications. This is the
prerequisite for grounding and labeling circuits, devices, and systems
in accordance with current standards in safety technology.
Qualified personnel are aware of the dangers that exist in their work.
Qualified personnel are familiar with appropriate measures against
these hazards in order to reduce the risk for themselves and others.
Qualified personnel receive training on a regular basis.
Device casing
Only technicians authorized by the manufacturer are permitted to open
the casing.
Never insert pointed objects (narrow screwdrivers, wires, etc.) into the
device or into the connection terminals for electric conductors. Do not
touch the connection terminals.
Make sure there is at least 3.94 inches (10 cm) of space in front of the
ventilation slits of the housing.
Keep the ventilation slits free to ensure good air circulation.
If you are operating the device in a living area or office environment,
only operate it in switch cabinets with fire protection characteristics in
accordance with EN 60950-1.
The surfaces of the device housing may become hot. Avoid touching
the device while it is operating.
Grounding the device
Grounding the device is by means of a separate ground connection on the
device.
Ground the device before connecting any other cables.
Disconnect the grounding only after disconnecting all other cables.
The overall shield of a connected shielded twisted pair cable is connected
to the ground connector on the front panel as a conductor.
Requirements for connecting electrical wires
Before connecting the electrical wires, always verify that the
requirements listed are complied with.
General requirements for connecting electrical wires
The following requirements apply without restrictions:
The electrical wires are voltage-free.
The cables used are permitted for the temperature range of the application case.
Relevant for North America:
Use 60/75 or 75 °C copper (Cu) wire only.

Installation MSM20/22/24/40/42/46/50
Release 09 11/2016 7
Supply voltage
Enable the supply voltage for the device only when the following
requirements are fulfilled:
the housing is closed
the terminal blocks are wired correctly
the terminal blocks for the supply voltage are connected
Internal fuses are triggered only in the case of a detected error in the
device. In case of damage or malfunction of the device, turn off the
supply voltage and return the device to the plant for inspection.
ESD Guidelines
The modules are equipped with electrostatically sensitive components.
These can be destroyed, or their life cycles reduced, by the effects of an
electrical field or by a charge equalization if the connections are touched.
You will find information about electrostatically endangered assemblies in
DIN EN 61340-5-1 (2007-08) and DIN EN 61340-5-2 (2007-08).
Requirements for connecting the signal contact
The following requirements apply without restrictions:
The voltage connected complies with the requirements for a safety extra-low voltage
(SELV) as per IEC/EN 60950-1.
The connected voltage is limited by a current limitation device or a fuse.
Observe the electrical threshold values for the signal contact.
See “General technical data” on page 47.
Requirements for connecting the supply voltage
The following requirements apply without restrictions:
All of the following requirements are complied with:
The supply voltage corresponds to the voltage specified on the type plate of the device.
The power supply conforms to overvoltage category I or II.
The power supply has an easily accessible disconnecting device (e.g., a switch or a plug).
This disconnecting device is clearly identified. So in the case of an emergency, it is clear
which disconnecting device belongs to which power supply cable.
The wire diameter of the power supply cable is at least 1 mm² (North America: AWG16) on
the supply voltage input.
The following requirements apply alternatively:
Alternative 1 The power supply complies with the requirements for a limited power source
(LPS) as per EN 60950-1.
Alternative 2 Relevant for North America:
The power supply complies with the requirements as per Class 2
Alternative 3 All of the following requirements are complied with:
The power supply complies with the requirements for a safety extra-low
voltage (SELV) as per IEC/EN 60950-1.
A fuse suitable for DC voltage is located in the plus conductor of the power
supply.
The minus conductor is on ground potential. Otherwise, a fuse is also
located in the minus conductor.
Regarding the properties of this fuse:
See “Technical data” on page 47.

8Installation MSM20/22/24/40/42/46/50
Release 09 11/2016
CE marking
The labeled devices comply with the regulations contained in the following
European directive(s):
2011/65/EU (RoHS)
Directive of the European Parliament and of the Council on the restriction
of the use of certain hazardous substances in electrical and electronic
equipment.
2014/30/EU (EMC)
Directive of the European Parliament and the council for standardizing the
regulations of member states with regard to electromagnetic
compatibility.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
www.hirschmann.com
The device can be used in the industrial sector.
Interference immunity: EN 61000-6-2
Emitted interference: EN 55022
You find more information on technical standards here:
“Technical data” on page 47
Warning! This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to take
appropriate measures.

Installation MSM20/22/24/40/42/46/50
Release 09 11/2016 9
LED or laser components
LED or LASER components in compliance with IEC 60825-1 (2007):
LASER CLASS 1 - CLASS 1 LASER PRODUCT, relevant for the
following F/O modules (indicated by the module code): S2, S4, G2, L2,
C1.
LED CLASS 1 - CLASS 1 LED PRODUCT, relevant for the following F/O
modules (indicated by the module code): M2, M4.
For a description of the nomenclature for module codes, see table 1 on
page 16.
FCC note:
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference; (2) this device must accept any interference received,
including interference that may cause undesired operation.
Appropriate testing has established that this device fulfills the
requirements of a class A digital device in line with part 15 of the FCC
regulations.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can also radiate these
frequencies. If it is not installed and used in accordance with this
operating manual, it can cause radio transmission interference. The use
of this device in a residential area can also cause interference, and in this
case the user is obliged to cover the costs of removing the interference.
Recycling note
After usage, this device must be disposed of properly as electronic waste,
in accordance with the current disposal regulations of your county, state,
and country.

10 Installation MSM20/22/24/40/42/46/50
Release 09 11/2016
The following approvals are only in place for the media
modules MSM20/24/40/42 in connection with a MSP30/32
basic device:
Relevant for Use as Industrial Control Equipment
(according to the Standards UL508 / CSA C22.2 No. 142-
1987)
When using the MSP30/32 devices as industrial control equipment the
following restrictions apply:
Max. surrounding air temperature: +140 °F (+60 °C)
(... to apply for operating temperature characteristic values S, T or E)
Use copper conductors only.
Temperature rating of field installed conductors:
Use 167 °F (75 °C) conductors only.
For use in Pollution Degree 2 Environment only.
Digital output (O1, ..., O4): max. 30 V DC, 1 A, resistive load.
Relevant for Use in Hazardous Locations Class I Div. 2
Groups A, B, C and D (according to the Standards
ANSI/ISA12.12.01-2013 / CSA C22.2 No.213-M1987)
When using the MSP30/32 devices as industrial control equipment the
following restrictions apply:
This equipment is suitable for use in Class I, Division 2, Groups A, B ,C,
D – OR non-hazardous locations, if labeled “FOR USE IN HAZARDOUS
LOCATIONS”.
Additional to the restrictions referring to UL508, the following restrictions
apply:
Ta: -40°F ... +140°F (-40°C ... +60°C), Temperature Code: T4
for temperature range characteristic value T and E
Ta: +32°F ... +140°F (0°C ... +60°C), Temperature Code: T4
for temperature range characteristic value S.
WARNING – EXPLOSION HAZARD – Do not disconnect equipment
unless power has been removed or the area is known to be non-
hazardous.
WARNING – EXPLOSION HAZARD – Substitution of any components
may impair suitability for Class I, Division 2.

Installation MSM20/22/24/40/42/46/50
Release 09 11/2016 11
– For installation and use of the MSM24 IO-modules the Control
Drawing No.000172850DNR is to apply - see the next two pages.
Avertissement - Risque d'explosion - Ne pas débrancher tant que le
circuit est sous tension à moins que l'emplacement soit connu pour ne
contenir aucune concentration de gaz inflammable.
Avertissement - Risque d'explosion - La substitution de tout composant
peut rendre ce matériel incompatible pour une utilisation en classe I,
division 2.

12 Installation MSM20/22/24/40/42/46/50
Release 09 11/2016
CONTROL DRAWING for MSM24-IOIOIOIO devices
for Use in Hazardous Locations Class I Division 2 , Groups A, B, C, D Rev. 0 Document No.:000172850DNR Page 1/2
Nonincendive field wiring parameters:
THE RELAY TERMINALS ARE DEPENDENT UPON THE FOLLOWING ENTY PARAMETERS: *)
U
i
I
i
C
i
L
i
30 V 90 mA 5 nF 1 µH
The Entity Parameters are to apply to the following pin combinations: pin 2 and pin 1; pin 2 and pin 3, pin 5 and pin 4; pin 5 and pin 6, pin 8 and pin 7; pin 8 and pin 9, pin 11 and pin10; pin 11 and pin 12.
Detail of MSM24-IOIOIOIO
Class I Division 2, Groups A, B, C, D
Hazardous Location
Ordinary Location, Non-Hazardous Area,
Nonexplosive Atmosphere
Pin

Installation MSM20/22/24/40/42/46/50
Release 09 11/2016 13
For Use in Hazardous Locations Class I Division 2 Groups A, B ,C ,D: Only allowed for MSP30 or MS32 model No´s. which are individually labelled ´)2586(,1+$=$5'286/2&$7,216µ
Nonincendive field wiring circuits must be wired in accordance with the National Electrical Code (NEC), NFPA 70 , article 501.
WARNING - EXPLOSION HAZARD – SUBSTITUTION OF ANY COMPONENTS MAY IMPAIR SUITABILITY FOR HAZARDOUS LOCATIONS OR EXPLOSIVE ATMOSPHERES. WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS. *) Notes: The nonincendive field wiring circuit concept allows interconnection of nonincendive field wiring apparatus and
associated nonincendive field wiring apparatus using any of the wiring methods permitted for unclassified locations when certain parametric conditions are met. Capacity: C
a
C
i
+ C
Cable
; Inductivity: L
a
L
i
+ L
Cable

   The maximum cable length has to be determined as follows: (a) max. Cable Length < max. Cable Length < (L
a
-L
i
) / Cable
L
(”Cable
L
“ denotes the inductance per unit length of used cable) and
(b) max. Cable Length < max. Cable Length < (C
a
-C
i
) / Cable
C
(“Cable
C
“ denotes the capacitance per unit length of used cable).
The lower value of (a) and (b) is to apply. Manufactured in 72654 Neckartenzlingen / Germany by Hirschmann Automation and Control GmbH. DOM: ww/yyyy (Date of manufactur w - week, Y - year. Refer to the device label).
CONTROL DRAWING for MSM24-IOIOIOIO devices
for Use in Hazardous Locations Class I Division 2 , Groups A, B, C, D Rev. 0 Document No.: 000172850DNR Page 2/2

14 Installation MSM20/22/24/40/42/46/50
Release 09 11/2016
Relevant for use in explosive atmospheres (European ATEX
Directive 2014/34/EU)
In Ex zone 2, only devices with a corresponding label may be operated.
When operating the MSM20/24/40/42 devices in Ex zone 2, the following
applies:
II 3G
Ex nA IIC T4 Gc
Ta: −40 °F ... +158 °F (−40 °C ... +70 °C) for temperature range
characteristic value T and E
Ta: +32 °F ... +140 °F (0 °C ... +60 °C) for temperature range
characteristic value S
DEKRA 13ATEX0090 X
DO NOT OPEN THE DEVICE WHEN IT IS ELECTRICALLY CHARGED.
Special conditions for safe use
The modules shall be installed in a suitable enclosure providing a
degree of protection of at least IP54 according to EN 60079-15, taking
into account the ambient conditions under which the equipment will be
used.
When the temperature under rated conditions exceeds 158 °F (70 °C)
on the cable or at conduit entry point, or 176 °F (80 °C) at the
branching point of the conductors, take measures so that the
temperature specification of the selected cable is in compliance with
the actual measured temperature values.
Provisions shall be made to prevent the rated voltage from being
exceeded by transient disturbances of more than 119 V.
Temperature code T4
List of
standards:
EN 60079-0:2012
EN 60079-15: 2010

Installation MSM20/22/24/40/42/46/50
Release 09 11/2016 15
About this manual
The “Installation” user manual contains a device description, safety
instructions, a description of the display, and the other information that you
need to install the device.
The following manuals are available as PDF files on the Internet on the
Hirschmann product pages (www.hirschmann.com):
Basic Configuration user manual
User Manual Installation MSM20/22/24/40/42/46/50
User Manual Installation MSP30/32/40/42
Redundancy Configuration user manual
Command Line Interface reference manual
Reference manual for the graphical user interface
Key
The symbols used in this manual have the following meanings:
Listing
Work step
Subheading

16 Installation MSM20/22/24/40/42/46/50
Release 09 11/2016
1 Description
1.1 General description
The MSM20/22/24/40/42/46/50 media modules are designed for the special
requirements of industrial automation. They meet the relevant technical
standards, provide very high operational reliability, even under extreme
conditions, and also long-term reliability and flexibility.
You have the option of choosing various media to connect to the terminal
devices and other network components:
multimode F/O
singlemode F/O
twisted pair cable
1.2 Device name and product code
The device name corresponds to the product code. The product code is
made up of characteristics with defined positions. The characteristic values
stand for specific product properties.
You have numerous options of combining the device characteristics. You can
determine the possible combinations using the configurator which is
available in the Belden E-Catalog (www.e-catalog.beldensolutions.com) on
the web page of the device.
Item Characteristic Characteristic
value
Description
1 ... 3 Product MSM MICE Switch Media Module
4 Data rate 2 10 a/100 Mbit/s ports
410
a/100/1000 Mbit/s ports
5 1000/2500 Mbit/s ports
5 Hardware type 0 Standard
2 Suitable for PoE or PoE+
4 Suitable for I/O operation
6 suitable for PoE or PoE+ with external power
supply
Table 1: Device name and product code

Installation MSM20/22/24/40/42/46/50
Release 09 11/2016 17
6 (hyphen) -
7 ... 8 Port 1 T1 Twisted Pair (TX) RJ45 socket
T5 Twisted Pair (TX) M12 socket
M2 Multimode FX DSC (100 Mbit/s only)
M4 Multimode FX ST (100 Mbit/s only)
S2 Singlemode FX DSC (100 Mbit/s only)
S4 Singlemode FX ST (100 Mbit/s only)
L2 Singlemode Long
Haul FX DSC
(100 Mbit/s only)
G2 Singlemode Long
Haul FX DSC 200 km
(100 Mbit/s only)
C1 Combo port:
Twisted Pair (TX)
F/O
RJ45 socket
SFP slot
IO Digital Input/Output
Q6 SFP slot 1000/2500 Mbit/s
99 Not present
9 ... 10 Port 2 See items 7 ... 8
11 ... 12 Port 3 See items 7 ... 8
13 ... 14 Port 4 See items 7 ... 8
15 Temperature
range
S Standard +32 °F ... +140 °F
(0 °C ... +60 °C)
T Extended −40 °F ... +158 °F
(−40 °C ... +70 °C)
under UL conditions:
max. +140 °F (+60 °C)
E Extended with conformal
coating
−40 °F ... +158 °F
(−40 °C ... +70 °C)
under UL conditions:
max. +140 °F (+60 °C)
16 ... 17 Certificates and
declarations
You will find detailed information on the certificates and
declarations applying to your device in a separate overview.
See table 3 on page 19.
18 ... 19 Customer-specific
version
HH Hirschmann standard
HX Hirschmann Extreme Conditions
MX MAN Extreme Conditions
20 Hardware
configuration
9None
21 Software
configuration
E Entry (Hirschmann Standard)
22 ... 26 Software version 99.9 Without software
a. Only for twisted pair connections
Item Characteristic Characteristic
value
Description
Table 1: Device name and product code

18 Installation MSM20/22/24/40/42/46/50
Release
09
11/2016
Application case Certificates and
declarations
Characteristic valuea
a. X= Approval or self-declaration present
(X)= Approval or self-declaration present for MSP30/32 and in preparation for MSP40/42
# = Approval or self-declaration only present for MSP30/32
(#) = Approval or self-declaration in preparation for MSP40/42
T9 TY U9 UW UX UY V9 VT VU VY W9 WY X9 Y9 Z9
Standard applications ATEX Zone 2 (X) (X) (X)
CE XXXXXXXXXXX X XXX
EN 60950-1 X X X XXXXXXXX X XXX
EN 61131-2 X X X XXXXXXXX X XXX
FCC XXXXXXXXXXX X XXX
ISA 12.12.01 –
Class I, Div. 2
(X) (X)
UL 508 (X) (X) (X) (X) (X) (X) (X) (X) (X) (X)
Substation applications IEC 61850-3 X X X X
IEEE 1613 X X X X
Navy applications GL # # # # #
DNVGL (#) (#) (#) (#) (#)
Railway applications EN 50121-4 X X X
Table 2: Assignment: application cases, certificates and declarations, characteristic values

Installation MSM20/22/24/40/42/46/50 Release
09
11/2016 19
Application case Certificates and
declarations
Characteristic valuea
a. X = Approval or self-declaration present
(X) = Approval or self-declaration present for MSM20/24/40/42 and in preparation for MSM22/46/50
# = Approval or self-declaration only present for MSM20/24/40/42
(#) = Approval or self-declaration in preparation for MSM22/46/50
T9 TY U9 UW UX UY V9 VT VU VY W9 WY X9 Y9 Z9
Standard applications ATEX Zone 2 # # #
CE XXXXXXXXXXX X XXX
EN 60950-1 X X X XXXXXXXX X XXX
EN 61131-2 X X X XXXXXXXX X XXX
FCC XXXXXXXXXXX X XXX
ISA 12.12.01 –
Class I, Div. 2
##
UL 508 (X) (X) (X) (X) (X) (X) (X) (X) (X) (X)
Substation applications IEC 61850-3 X X X X
IEEE 1613 X X X X
Navy applications GL # # # # #
DNVGL (#) (#) (#) (#) (#)
Railway applications EN 50121-4 X X X
Table 3: Assignment: application cases, certificates and declarations, characteristic values

20 Installation MSM20/22/24/40/42/46/50
Release 09 11/2016
1.3 Slots of the basic device
Depending on their varian, the basic devices offer you the following number
of slots for media modules and the following maximum amount of
connectable network segments:
The maximum data rate of the media modules depends on their slot on the
basic device. Some media modules only support data rates up to
10/100 Mbit/s.
See “Device name and product code” on page 16.
Basic device Total
number
of slots
Number of
slots for
10/100 Mbit/s
(FE)
Number of
slots for
1000 Mbit/s
(GE)
Max. number of
connectable
10/100 Mbit/s
network
segments
Max. number of
connectable
1000 Mbit/s
network
segments
MSP30-0804...
MSP32-0804...
32 1 12 4
MSP30-1604...
MSP32-1604...
54 1 20 4
MSP30-2404...
MSP32-2404...
76 1 28 4
Table 4: Number of slots and maximum connectable network segments
Basic device Total
number of
slots
Number of
slots for
10/100/1000
Mbit/s (GE)
Number of
slots for
10/100/1000
Mbit/s (GE)
Max. number of
connectable
10/100/1000 Mbit
/s network
segments
Max. number of
connectable
1000/2500 Mbit/s
network
segments
MSP40-0012...
MSP42-0012...
32 1 8 4
MSP40-0020...
MSP42-0020...
54 1 16 4
MSP40-0028...
MSP42-0028...
76 1 24 4
Table 5: Number of slots and maximum connectable network segments