Hirschmann MSM20 User manual

Installation MSM20/22/24/40/42
Release 05 11/2014
Technical Support
https://hirschmann-support.belden.eu.com
User Manual
Installation
MICE Switch Media Modules
MSM20/22/24/40/42

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2014 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. For devices with embedded software, the end-user license agreement on the
enclosed CD/DVD applies.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Printed in Germany
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
MSM20/22/24/40/42 040 010-001-05-1114 - 24.10.2014

Installation MSM20/22/24/40/42
Release 05 11/2014 3
Contents
Safety instructions 5
About this manual 13
Key 13
1 Description 14
1.1 General description 14
1.2 Device name and product code 15
1.3 Combination options 19
1.4 Slots in the basic module 21
1.5 Media modules 23
1.5.1 Media modules MSM20 23
1.5.2 Media modules MSM40 25
1.5.3 PoE-capable media modules MSM22 and MSM42 26
1.6 MSM24 I/O module 27
1.7 SFP Transceiver 29
1.8 Ethernet ports 29
1.9 Display elements 32
1.9.1 MSM20 media modules 32
1.9.2 MSM40 media modules 33
1.9.3 MSM22 and MSM42 media modules 34
1.9.4 MSM24 I/O module 35
2 Installation 36
2.1 Checking the package contents 36
2.2 Installing media modules 36
2.2.1 Device variants featuring customer-specific version
with the characteristic value HH 37
2.2.2 Device variants featuring customer-specific version
with the characteristic value HX 38
2.3 Connecting an I/O module 38
2.3.1 Connecting actuators and sensors 38
2.4 Installing an SFP transceiver (optional) 40
2.5 Connecting data cables 40
2.5.1 10/100 Mbit/s twisted pair port 41
2.5.2 10/100/1000 Mbit/s twisted pair port 41

4Installation MSM20/22/24/40/42
Release 05 11/2014
2.5.3 100/1000 Mbit/s F/O port 41
2.5.4 100 Mbit/s F/O port 41
3 Maintenance and service 42
4Disassembly 43
4.1 Removing an SFP transceiver (optional) 43
4.2 Removing a media module 43
4.2.1 Device variants featuring customer-specific version
with the characteristic value HH 43
4.2.2 Device variants featuring customer-specific version
with the characteristic value HX 44
5 Technical data 45
A Further Support 55

Installation MSM20/22/24/40/42
Release 05 11/2014 5
Safety instructions
General safety instructions
You operate this device with electricity. The proper and safe operation of
this device depends on proper handling during transportation, proper
storage and assembly, and conscientious operation and maintenance
procedures. Improper use of this device is associated with the risk of
personal injury or property damage.
Read this documentation as well as the safety instructions and warn-
ings before connecting any cables.
Never start operation with damaged components.
The device does not contain any service components. If the device is
not functioning correctly, or if it is damaged, turn off the power supply
and return the device to Hirschmann for inspection.
Qualification requirements for personnel
Only allow qualified personnel to work on the device.
Qualified personnel have the following characteristics:
Qualified personnel are properly trained. Training as well as practical
knowledge and experience make up their qualifications. This is the
prerequisite for grounding and labeling circuits, devices, and systems
in accordance with current standards in safety technology.
Qualified personnel are aware of the dangers that exist in their work.
Qualified personnel are familiar with appropriate measures against
these hazards in order to reduce the risk for themselves and others.
Qualified personnel receive training on a regular basis.
WARNING
UNCONTROLLED MACHINE ACTIONS
To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

6Installation MSM20/22/24/40/42
Release 05 11/2014
Intended usage
Use the product only for the application cases described in the
Hirschmann product information, including this manual.
Operate the product only according to the technical specifications.
See “Technical data” on page 45.
Connect to the product only components suitable for the requirements
of the specific application case.
National and international safety regulations
Verify that the electrical installation meets local or nationally applicable
safety regulations.
Grounding the device
Grounding the device is by means of a separate ground connection on the
device.
Ground the device before connecting any other cables.
Disconnect the grounding only after disconnecting all other cables.
The overall shield of a connected shielded twisted pair cable is connected
to the ground connector on the front panel as a conductor.
Housing
Only technicians authorized by the manufacturer are permitted to open
the housing.
Never insert pointed objects (narrow screwdrivers, wires, etc.) into the
device or into the connection terminals for electric conductors. Do not
touch the connection terminals.
Keep the ventilation slits free to ensure good air circulation.
Make sure there is at least 3.94 inches (10 cm) of space in front of the
ventilation slits of the housing.
If you are operating the device in a living area or office environment,
only operate it in switch cabinets with fire protection characteristics in
accordance with EN 60950-1.
ESD Guidelines
The modules are equipped with electrostatically sensitive components.
These can be destroyed, or their life cycles reduced, by the effects of an
electrical field or by a charge equalization if the connections are touched.
You will find information about electrostatically endangered assemblies in
DIN EN 61340-5-1 (2007-08) and DIN EN 61340-5-2 (2007-08).

Installation MSM20/22/24/40/42
Release 05 11/2014 7
CE marking
The labeled devices comply with the regulations contained in the following
European directive(s):
2011/65/EU (RoHS)
Directive of the European Parliament and of the Council on the restriction
of the use of certain hazardous substances in electrical and electronic
equipment.
2004/108/EC (EMC)
Directive of the European Parliament and the council for standardizing the
regulations of member states with regard to electromagnetic compati-
bility.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
The device can be used in the industrial sector.
Interference immunity: EN 61000-6-2
Emitted interference: EN 55022
Reliability: EN 60950-1
You find more information on technical and industry standards here:
See “Technical data” on page 45.
Warning! This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to take appro-
priate measures.
LED or laser components
LED or LASER components in compliance with IEC 60825-1 (2007):
LASER CLASS 1 - CLASS 1 LASER PRODUCT, relevant for the
following F/O modules (indicated by the module code): S2, S4, G2, L2,
C1.
LED CLASS 1 - CLASS 1 LED PRODUCT, relevant for the following F/O
modules (indicated by the module code): M2, M4.
For a description of the nomenclature for module codes.
See “Device name and product code” on page 15.

8Installation MSM20/22/24/40/42
Release 05 11/2014
Relevant for Use as Industrial Control Equipment
(according to the Standards UL508 / CSA C22.2 No. 142-
1987)
When using the MSM20/22/24/40/42 devices as industrial control equip-
ment the following restrictions apply:
Max. surrounding air temperature: +60 °C
(... to apply for operating temperature characteristic values S, T or E)
Use Copper Conductors only.
Temperature rating of field installed conductors:
Use 75 °C conductors only.
For use in Polution Degree 2 Environment only.
Digital Output (O1, ..., O4): max. 30 V DC, 1 A, resistive load.
Relevant for Use in Hazardous Locations Class I Div. 2
Groups A, B ,C and D (according to the Standards
ANSI/ISA12.12.01-2013 / CSA C22.2 No.213-M1987)
This equipment is suitable for use in Class I, Division 2, Groups A, B ,C,
D– OR non-hazardous locations, if labeled "FOR USE IN HAZARDOUS
LOCATIONS".
Additional to the restrictions refering UL508 the following restriction-
sapply:
Ta: -40°F ... +140°F (-40°C ... +60°C), Temperature Code: T4
for temperature range characteristic value T and E
Ta: +32°F ... +140°F (0°C ... +60°C), Temperature Code: T4
for temperature range characteristic value S.
WARNING – EXPLOSION HAZARD – Do not disconnect equipment
unless power has been removed or the area is known to be non-
hazardous.
WARNING – EXPLOSION HAZARD – Substitution of any compo-
nentsmay impair suitability for Class I, Division 2.
– For installation and use of the MSM24 IO- modules the Control
Drawing No.000172850DNR is to apply - see the next two pages.

Installation MSM20/22/24/40/42
Release 05 11/2014 9
CONTROL DRAWING for MSM24-IOIOIOIO devices
for Use in Hazardous Locations Class I Division 2 , Groups A, B, C, D Rev. 0 Document No.:000172850DNR Page 1/2
Nonincendive field wiring parameters:
THE RELAY TERMINALS ARE DEPENDENT UPON THE FOLLOWING ENTY PARAMETERS: *)
U
i
I
i
C
i
L
i
30 V 90 mA 5 nF 1 µH
The Entity Parameters are to apply to the following pin combinations: pin 2 and pin 1; pin 2 and pin 3, pin 5 and pin 4; pin 5 and pin 6, pin 8 and pin 7; pin 8 and pin 9, pin 11 and pin10; pin 11 and pin 12.
Detail of MSM24-IOIOIOIO
Class I Division 2, Groups A, B, C, D
Hazardous Location
Ordinary Location, Non-Hazardous Area,
Nonexplosive Atmosphere
Pin

10 Installation MSM20/22/24/40/42
Release 05 11/2014
For Use in Hazardous Locations Class I Division 2 Groups A, B ,C ,D: Only allowed for MSP30 or MS32 model No´s. which are individually labelled ´)2586(,1+$=$5'286/2&$7,216µ
Nonincendive field wiring circuits must be wired in accordance with the National Electrical Code (NEC), NFPA 70 , article 501.
WARNING - EXPLOSION HAZARD – SUBSTITUTION OF ANY COMPONENTS MAY IMPAIR SUITABILITY FOR HAZARDOUS LOCATIONS OR EXPLOSIVE ATMOSPHERES. WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS. *) Notes: The nonincendive field wiring circuit concept allows interconnection of nonincendive field wiring apparatus and
associated nonincendive field wiring apparatus using any of the wiring methods permitted for unclassified locations when certain parametric conditions are met. Capacity: C
a
C
i
+ C
Cable
; Inductivity: L
a
L
i
+ L
Cable

   The maximum cable length has to be determined as follows: (a) max. Cable Length < max. Cable Length < (L
a
-L
i
) / Cable
L
(”Cable
L
“ denotes the inductance per unit length of used cable) and
(b) max. Cable Length < max. Cable Length < (C
a
-C
i
) / Cable
C
(“Cable
C
“ denotes the capacitance per unit length of used cable).
The lower value of (a) and (b) is to apply. Manufactured in 72654 Neckartenzlingen / Germany by Hirschmann Automation and Control GmbH. DOM: ww/yyyy (Date of manufactur w - week, Y - year. Refer to the device label).
CONTROL DRAWING for MSM24-IOIOIOIO devices
for Use in Hazardous Locations Class I Division 2 , Groups A, B, C, D Rev. 0 Document No.: 000172850DNR Page 2/2

Installation MSM20/22/24/40/42
Release 05 11/2014 11
Relevant for use in Ex Zone 2 according to ATEX 95
(European directive 94/9/EC)
In Ex zone 2, solely the devices with a corresponding label may be oper-
ated.
When operating the MSM20/24/40/42 devices in Ex zone 2, the following
applies:
II 3G
Ex nA IIC T4 Gc
Ta: −40 °F ... +158 °F (−40 °C ... +70 °C) for temperature range
characteristic value T and E
Ta: +32 °F ... +140 °F (0 °C ... +60 °C) for temperature range
characteristic value S
DEKRA 13ATEX0090 X
DO NOT OPEN THE DEVICE WHEN IT IS ELECTRICALLY
CHARGED.
Special conditions for safe use
The modules shall be installed in a suitable enclosure providing a
degree of protection of at least IP54 according to EN 60529, taking
into account the environmental conditions under which the equipment
will be used.
When the temperature under rated conditions exceeds 70 °C on the
cable or at conduit entry point, or 80 °C at the branching point of the
conductors, the temperature specification of the selected cable shall
be in compliance with the actual measured temperature values.
Make provisions to prevent the voltage of the rated voltage connec-
tions from excess due to transient disturbances of the 119 V threshold.
FCC note:
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference; (2) this device must accept any interference received,
including interference that may cause undesired operation.
Temperature code T4
List of standards: EN 60079-0: 2012
EN 60079-15: 2010

12 Installation MSM20/22/24/40/42
Release 05 11/2014
Appropriate testing has established that this device fulfills the require-
ments of a class A digital device in line with part 15 of the FCC regula-
tions.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can also radiate these
frequencies. If it is not installed and used in accordance with this oper-
ating manual, it can cause radio transmission interference. The use of this
device in a residential area can also cause interference, and in this case
the user is obliged to cover the costs of removing the interference.
Recycling note
After usage, this device must be disposed of properly as electronic waste,
in accordance with the current disposal regulations of your county, state,
and country.

Installation MSM20/22/24/40/42
Release 05 11/2014 13
About this manual
The “Installation” user manual contains a device description, safety instruc-
tions, a description of the display, and the other information that you need to
install the device.
The following manuals are available as PDF files on the CD/DVD supplied:
Basic Configuration user manual
User Manual Installation MSM20/22/24/40/42
User Manual Installation MSP30/32
Redundancy Configuration user manual
Command Line Interface user manual
Reference manual for the graphical user interface
Key
The symbols used in this manual have the following meanings:
Listing
Work step
Subheading

14 Installation MSM20/22/24/40/42
Release 05 11/2014
1 Description
1.1 General description
You can choose from between a wide range of variants. You have the option
to set up your device individually based on different criteria:
Number of ports
Types of connectors
Temperature range
Transmission speed
Certifications
The MSM20/22/24/40/42 media modules are designed for the special
requirements of industrial automation. They meet the relevant technical stan-
dards, provide very high operational reliability, even under extreme condi-
tions, and also long-term reliability and flexibility.
You have the option of choosing various media to connect to the terminal
devices and other network components:
multimode F/O
singlemode F/O
twisted pair cable

Installation MSM20/22/24/40/42
Release 05 11/2014 15
1.2 Device name and product code
The device name corresponds to the product code. The product code is
made up of characteristics with defined positions. The characteristic values
stand for specific product properties.
Item Characteristic Charac-
teristic
value
Description
1 ... 3 Product MSM MICE Switch media modules
4 Data rate 2 10 a/100 Mbit/s ports
410
a/100/1000 Mbit/s ports
5 Hardware type 0 Standard
2 Suitable for PoE or PoE+
4 Suitable for I/O operation
6 (hyphen) -
7 ... 8 Port 1 T1 Twisted Pair (TX) RJ45 socket
T5 Twisted Pair (TX) M12 socket
M2 Multimode FX DSC (100 Mbit/s only)
M4 Multimode FX ST (100 Mbit/s only)
S2 Singlemode FX DSC (100 Mbit/s only)
S4 Singlemode FX ST (100 Mbit/s only)
L2 Singlemode Long
Haul FX DSC
(100 Mbit/s only)
G2 Singlemode Long
Haul FX DSC 200 km
(100 Mbit/s only)
C1 Combo port:
Twisted Pair (TX)
F/O
RJ45 socket
SFP slot
IO Digital Input/Output
99 Not present
9 ... 10 Port 2 See items 7 ... 8
11 ... 12 Port 3 See items 7 ... 8
13 ... 14 Port 4 See items 7 ... 8
15 Temperature range S Standard +32 °F ... +140 °F (0 °C
... +60 °C)
T Extended −40 °F ... +158 °F
(−40 °C ... +70 °C)
under UL conditions:
max. +140 °F (+60 °C)
E Extended with conformal
coating
−40 °F ... +158 °F
(−40 °C ... +70 °C)
under UL conditions:
max. +140 °F (+60 °C)
16 ... 17 Certificates and
declarations bYou will find detailed information on the certificates and declara-
tions applying to your device in a separate overview.
See table 2 on page 17.
Table 1: Device name and product code

16 Installation MSM20/22/24/40/42
Release 05 11/2014
18 ... 19 Customer-specific
version
HH Hirschmann standard
HX Hirschmann Extreme Conditions
20 Hardware configu-
ration
9None
21 Software configura-
tion
E Entry (Hirschmann Standard)
22 ... 26 Software version 99.9 Without software
a. Only for twisted pair connections
b. Certificates and declarations in brackets are being prepared.
Item Characteristic Charac-
teristic
value
Description
Table 1: Device name and product code

Installation MSM20/22/24/40/42 Release
05
11/2014 17
Application case Certificates and
declarations
Characteristic value
T9 TY U9 UW UX UY V9 VT VU VY W9 WY X9 Y9 Z9
Standard applications ATEX Zone 2 X X X
CE XXXXXXXXXXX X XXX
EN 60950-1 X X X XXXXXXXX X XXX
EN 61131-2 X X X XXXXXXXX X XXX
FCC XXXXXXXXXXX X XXX
ISA 12.12.01 –
Class I, Div. 2
XX
UL508 X XXX XXX X XX
Substation applications IEC 61850-3 X X X X
IEEE 1613 X X X X
Navy applications GL X X X X X
Railway applications EN 50121-4 X X X
Table 2: Assignment: application cases, certificates and declarations, characteristic values

18 Installation MSM20/22/24/40/42
Release
05
11/2014
Figure 1: Example of a device name:
MSM40-C1C1C1C1SZ9HH9E99.9
3RVLWLRQ
060

&
6












3URGXNWQDPH
0,&(6ZLWFK0HGLHQPRGXO
0HUNPDOXQG%HVFKUHLEXQJ
'DWHQUDWHGHU(WKHUQHW3RUWV
0ELWV
²
+DUGZDUH7\S
6WDQGDUG
3RUW
&RPER3RUW7ZLVWHG3DLU7;5-XQG/:/6)36FKDFKW
3RUW
&RPER3RUW7ZLVWHG3DLU7;5-XQG/:/6)36FKDFKW
3RUW
&RPER3RUW7ZLVWHG3DLU7;5-XQG/:/6)36FKDFKW
3RUW
&RPER3RUW7ZLVWHG3DLU7;5-XQG/:/6)36FKDFKW
=XODVVXQJHQXQG(LJHQHUNOlUXQJHQ
&()&&(1(1
7HPSHUDWXUEHUHLFK
6WDQGDUG&&
.XQGHQVSH]LILVFKH9HUVLRQ
+LUVFKPDQQ6WDQGDUG
+DUGZDUH.RQILJXUDWLRQ
NHLQH


6RIWZDUH.RQILJXUDWLRQ
(QWU\+LUVFKPDQQ6WDQGDUG
6RIWZDUH9HUVLRQ
RKQH6RIWZDUH

±
& & & = ++
 (

Installation MSM20/22/24/40/42 Release
05
11/2014 19
1.3 Combination options
1 ... 3
Produc
t name
4 ... 5
Data rate
and hard-
ware type
6
—
(hyphen)
7 ... 8
Port
1
9 ... 10
Port 2
11 ... 12
Port 3
13 ... 14
Port 4
15
Tempera
ture
range
16 ... 17
Certifications
18 ... 19
Customer-
specific
version
20
Hardware
configura-
tion
21
Software
configura-
tion
22 ... 26
Software
version
MSM 20 — xxaT1 T1 T1 S; T; E Z9; Y9; X9; W9; WY;
V9; VY; VT; VU; T9; TY;
U9; UY; UW; UX
HH 9 E 99.9
MSM 20 — xxaxxaT1 T1 S; T; E Z9; Y9; X9; W9; WY;
V9; VY; VT; VU; T9; TY;
U9; UY; UW; UX
HH 9 E 99.9
MSM 20 — xxaxxaxxaxxaS; T; E Z9; Y9; X9; W9; WY;
V9; VY; VT; VU; T9; TY;
U9; UY; UW; UX
HH 9 E 99.9
MSM 20 — T5 T5 T5 T5 S; T; E Z9; Y9; V9; VY, VU, VT,
T9; TY, U9; UY
HX 9 E 99.9
MSM 20 — T5 T5 T5 T5 S; T; E Z9; Y9; V9; VY; VU; VT;
T9; TY;U9;UY
HH 9 E 99.9
MSM 22 — T5 T5 T5 T5 S; T; E Z9; Y9; V9; VY; VU; VT;
T9; TY;U9;UY
HH 9 E 99.9
MSM 24 — IO IO IO IO S; T; E Z9; Y9; X9; W9; WY;
V9; VY; VT; VU; T9; TY;
U9; UY; UW; UX
HH 9 E 99.9
MSM 40 — T1 T1 T1 T1 S; T; E Z9; Y9; X9; W9; WY;
V9; VY; VT; VU; T9; TY;
U9; UY; UW; UX
HH 9 E 99.9
Table 3: Combination options of the MSM device variants

20 Installation MSM20/22/24/40/42
Release
05
11/2014
MSM 40 — C1 C1 C1 C1 S; T; E Z9; Y9; X9; W9; WY;
V9; VY; VT; VU; T9; TY;
U9; UY; UW; UX
HH 9 E 99.9
MSM 42 — T1 T1 T1 T1 S; T; E Z9; Y9; X9; W9; WY;
V9; VY; VT; VU; T9; TY;
U9; UY; UW; UX
HH 9 E 99.9
a. xx = M2, M4, S2, S4, L2, G2
1 ... 3
Produc
t name
4 ... 5
Data rate
and hard-
ware type
6
—
(hyphen)
7 ... 8
Port
1
9 ... 10
Port 2
11 ... 12
Port 3
13 ... 14
Port 4
15
Tempera
ture
range
16 ... 17
Certifications
18 ... 19
Customer-
specific
version
20
Hardware
configura-
tion
21
Software
configura-
tion
22 ... 26
Software
version
Table 3: Combination options of the MSM device variants